Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ronix 8530
Summary of Contents for Ronix 8530
- Page 1 3.6V LITHIUM CORDLESS SCREWDRIVER 8530...
-
Page 3: Specifications
SPECIFICATIONS Voltage 3.6v Battery Capacity 1.5Ah No Load speed 210RPM Max. Torque 5N.m Charger voltage-frequency 220v-50Hz Net weight 0.42Kg Bits, Sockets: 40pcs Accessories Charger: 1pcs PARTS LIST WARNING: For your personal safety, read and understand before using. USER MANUAL... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE The term “power tool” in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. -
Page 5: Personal Safety
risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. - Page 6 Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Page 7 moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Page 8 SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. INSTRUCTIONS FOR USE SAFETY RULES FOR CORDLESS SCREWDRIVERS Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring.
- Page 9 over the bit is reduced and the loss of control is increased. Do not run the tool while carrying it at your side. A spinning bit could become entangled with clothing and injury may result. Do not use dull or damaged bits and accessories. Dull or damaged bits have a greater tendency to bind in the workpiece.
-
Page 10: Battery Care
Do not recharge battery in damp or wet environment. Do not expose charger to rain or snow. If battery case is cracked or otherwise damaged, do not insert into charger. Battery short or fire may result. Charge battery pack in temperatures above +32 degrees F (0 degrees C) and below +113 degrees F (45 degrees C). -
Page 11: Operation
result. Prior to disposal, protect exposed terminals with heavy insulating tape to prevent shorting. Lithium-ion Batteries If equipped with a lithium-ion battery, the battery must be collected, recycled or disposed of in an environ mentally sound manner. BATTERY REMOVAL INSTRUCTIONS Run motor until battery is completely discharged before attempting to remove battery from your tool. -
Page 12: Initial Charge
INITIAL CHARGE Charge your battery for 5-7 hours then use it until it runs down and only slowly operates, Recharge for 5-7 hours again. Once again run your tool until only a small amount of charge remains. Repeat the above cycle abut 4 or 5 times, this should set the battery “memory”, then charge as earlier stated. -
Page 13: On/Off Switch
REPLACEMENT DRIVER BITS Always ensure you only use single ended 25mm driver bits as shorter driver bits may become stuck or hard to remove from the screwdriver. ON/OFF SWITCH Depress the On/Off trigger switch to start the Driver and keep holding it for continuous operation. -
Page 14: Led Light
OPERATION OF THE DRIVER Only use driver/drill bits which can be securely fastened in the 1/4 “ magnetic bit holder. Before using the screwdriver check whether the screw-bit is inserted correctly. Avoid over tightening screws, otherwise the screw head may become damaged or stripping of the threads may occur. -
Page 15: Environmental Protection
it is free from all dust particles which may build up. Build up of dust particles may cause the tool to overheat and fail. - If the enclosure of the tool requires cleaning do not use solvents but a moist soft cloth only. Never let any liquid get inside the tool;...
Need help?
Do you have a question about the 8530 and is the answer not in the manual?
Questions and answers