Table of Contents
Advertisement
Quick Links
Tiertime Filament Dryer
PRO
Instruction Manual
MODELS:
FD2003-120
(110-120VAC, 60Hz, 300W)
FD2003-220
(220-240VAC, 50Hz, 300W)
THANK YOU FOR PUCHASING THE PRINTDRY FILAMENT DRYER.
BEFORE
OPERATING, PLEASE MAKE SURE YOUR ELECTRICAL VOLTAGE MATCHES THE
DRYER MODEL.
PLEASE ALSO READ, UNDERSTAND AND FOLLOW THESE
INSTRUCTIONS. BE SURE TO SAVE THIS BOOKLET FOR FUTURE REFERENCE.
Version: 2020-08
- 1 -
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TierTime Filament Dryer PRO
Summary of Contents for TierTime Filament Dryer PRO
- Page 1 Tiertime Filament Dryer Instruction Manual MODELS: FD2003-120 (110-120VAC, 60Hz, 300W) FD2003-220 (220-240VAC, 50Hz, 300W) THANK YOU FOR PUCHASING THE PRINTDRY FILAMENT DRYER. BEFORE OPERATING, PLEASE MAKE SURE YOUR ELECTRICAL VOLTAGE MATCHES THE DRYER MODEL. PLEASE ALSO READ, UNDERSTAND AND FOLLOW THESE INSTRUCTIONS.
-
Page 2: Important Safeguards
1. IMPORTANT SAFEGUARDS When using an electrical device, basic safety precautions should always be followed, including the following: Read all instructions before using the Tiertime filament dryer (hereinafter referred as the "dryer"). Always use a heat resistant surface. ... - Page 3 Failure to use and maintain the dryer in accordance with the instructions outlined in this manual will void the warranty and liability of dryer manufacturer. WARNING: MISUSE OF TIERTIME PRODUCTS INVOLVES SERIOUS RISKS INCLUDING INJURY AND PROPERTY DAMAGE. 2. INTRODUCTION The model FD2003 offers an easy and quick way to remove moisture from filaments for better quality of 3D printing.
- Page 4 Fig.1 Dryer Standard Package for 2 Spools (max OD 200mm or 8" each) Fig.2 Dryer Used for 1 Large Spool (max OD 300mm or 12") - 4 -...
-
Page 5: Description Of Parts
DESCRIPTION OF PARTS 1 Top lid 2 Filament Spools 3 Central Support 4 Rectangular Tray (2x) 5 Dryer Base Unit Fig.3 Tiertime Filament Dryer - 5 -... -
Page 6: How To Use
Wipe the base with a slightly damp cloth. NEVER IMMERSE THE BASE IN WATER OR ANY OTHER LIQUID. 3. HOW TO USE Tiertime filament dryer offers two functions – Dry and Feed+Dry: Dry Function Prepare filament spools with the mounting rods and mounting adaptors, as shown in the figure below. - Page 7 Feed + Dry Function Follow steps 1 and 2 in the previous section. Pass the filament through the holes in the plastic trays and feed it into your 3D printer, it is very important to adjust the dryer’s position for a smooth feeding.
-
Page 8: Care And Maintenance
CARE AND MAINTENANCE Turn off the dryer. Unplug from the wall outlet. If needed, wash the base with a soft, slightly damp cloth or sponge. DO NOT allow water or any other liquid to get into the dryer base. ... -
Page 9: Warranty
5. WARRANTY Tiertime filament dryer is warranted to be free from defect in material and workmanship for a period of ONE year under normal use after its original purchase date. This warranty extends only to the original retail purchaser. If the device should become defective within the warranty period, please contact us for repair or replacement. -
Page 10: Customer Support
6. CUSTOMER SUPPORT The Tiertime filament dryers (Model FD2003-120 and Model FD2003-220) have been respectively certified or in the process of being certified by: For product updates and more information about Tiertime filament dryers, please contact us at: www.tiertime.com tiertime@tiertime.net...
Need help?
Do you have a question about the Filament Dryer PRO and is the answer not in the manual?
Questions and answers