Advertisement
Available languages
Available languages
N
ightlight
IMPORTANT WARNING
WARNING: The opening between the side of the door
and the outer-most vertical members of the barrier shall
be less than 60 mm
IMPORTANT: Please read these instructions carefully be-
fore use and keep them for future reference. For your
child's safety barrier, read these instructions carefully.
WARNING: Before use, remove and dispose of all plastic
bags and packaging materials and keep them out of
reach of newborn babies and children.
IMPORTANT – READ AND FOLLOW THESE IN-
STRUCTIONS CAREFULLY AND KEEP FOR FUTURE
REFERENCE.
WARNINGS
•
WARNING: Incorrect installation can be dangerous.
•
WARNING: This safety barrier barrier must not be fit-
ted across windows.
•
Only use this product as a staircase and door guard.
This safety barrier is for domestic use only.
•
This safety barrier has been designed for children up
to 24 months of age.
•
WARNING: Children over 24 months of age could
climb on the guard and pose a risk of danger to their
safety barrier.
•
WARNING: Stop using the safety barrier barrier if the
child is capable of climbing it.
•
WARNING: Periodically check that the guard is fitted
and fixed correctly.
•
Check that the surfaces where you wish to fit the
guard are suitable for this purpose and that they are
structurally solid.
•
WARNING: Do not use the safety barrier if any compo-
nents are damaged or missing.
•
WARNING: Only use spare parts supplied or approved
by Artsana S.p.A..
•
WARNING: The safety gate must be fitted in such a way
so that it opens in the direction opposite to the stairs.
•
WARNING: Never use without wall cups
•
The safety barrier closes and locks in place automati-
cally. Check that the safety barrier is closed properly.
MAINTENANCE
Periodically check the condition of the anchoring sur-
faces, cranks, shafts, wall caps and the correct operation
of the locking device of the safety barrier guard.
The cleaning and maintenance of this product must
be carried out on a regular basis by the user. The
cleaning and maintenance must only be carried out
by an adult.
•
Clean the plastic parts with a soft damp cloth.
•
If the highchair comes into contact with water, dry
the metal parts to prevent the formation of rust.
PACK CONTENT (DIAGRAM A)
1. Safety gate
2. Shaft (x 4)
3. Crank (x 4)
4. Wall cap (x 4)
5. Adhesive strips (x 4)
6. Screw (x 4)
7. Spacer for fitting the guard.
HOW TO ASSEMBLE THE PRODUCT
Screw the cranks to the end of the shafts, taking care to
fit them in the correct positions, as shown in diagram B.
Insert each shaft, with the crank correctly tightened into
position, into each of the appropriate housings located
on the corners of the guard (diagram B).
HOW TO POSITION THE SAFETY BARRIER GUARD
Minimum width: 760 mm
Maximum width: 810 mm
The safety gate can be fitted with extensions to suit larger
openings.
WARNING: Fitting the guard in the incorrect position can
be dangerous for your child's safety barrier.
The guard must be fitted in such a way so that it opens in
the direction opposite to the staircase.
WARNING: If the safety gate is positioned at the top of
the stairs, it must not be fitted below the highest step. If
the safety gate is positioned at the bottom of the stairs,
it must be fitted in correspondence with the lowest step
(diagram C). Check that the surfaces on which the safety
gate is fitted are suitable and solid.
Note: Fitting the safety gate to certain surfaces may require
purchasing appropriate fixing accessories (i.e.: inserts).
HOW TO FIT THE SAFETY BARRIER GUARD
WARNING: To ensure the correct operation of the auto-close
locking mechanism, the safety gate must be fitted in a per-
pendicular position with respect to the floor' s surface, as
shown in diagram D.
HOW TO ASSEMBLE AND USE THE SAFETY GATE
Place the safety gate in a central position with respect to
the opening, as shown in diagram E. The safety gate must
be perfectly perpendicular with respect to the floor sur-
face. Adjust the right and left cranks to the same degree,
ensuring that the safety gate is tightly fixed to the wall
caps. Ensure that the latter are firmly fitted to the anchor-
ing surfaces. Mark the position of the four wall caps on
the anchoring surface, then remove the safety gate. De-
pending on the type of anchoring surface, glue or screw
the wall caps to the marked positions, using the adhesive
strips or the screws supplied, as explained in the paragraph
"How to Position the Safety gate" above. Carry out this op-
eration with the appropriate fixing accessories (i.e.: inserts).
WARNING: If the anchoring surfaces are covered with
wallpaper, have air bubbles or are damaged, the caps
must be fixed with the screws.
Replace the safety gate, ensuring that the external bars
are placed at same distance with respect to the an-
choring surfaces; then fit the shafts into the wall caps.
Screw the cranks of the shafts to the same degree, in
correspondence with the lower part of the safety gate,
checking that that they are in contact with the safety
gate. Screw them tightly and ensure they are correctly
fixed into position.
Screw the cranks of the shafts, in correspondence with
the lower part of the safety gate, to the same degree,
until they are in contact with the safety gate. Tighten the
12
Advertisement
