Subscribe to Our Youtube Channel
Related Manuals for DK2 Power OPC566E
Summary of Contents for DK2 Power OPC566E
- Page 1 OPC566E 6IN CHIPPER User Manual SAFETY AND OPERATION INSTRUCTIONS IMPORTANT: Read safety rules and instructions carefully before operating equipment.
-
Page 2: Table Of Contents
Table of Contents Table of Contents PART I: General Safety Rules ......................2 PART II: Familiar with the Wood Chipper ..................8 PART III: Operating the Wood Chipper .................... 9 PART IV: Maintaining the Wood Chipper..................11 PART V: Troubleshooting and Parts List ..................13 Conventions used in this manual WARNING This indicates a hazardous situation, which, if not avoided, could result in death or serious... -
Page 3: Part I: General Safety Rules
Part I: General Safety Rules PART I: General Safety Rules Safety Labels Found on Your Unit... - Page 4 Part I: General Safety Rules Should make sure the emergency stop switch is available before every use. Or may result in serious injury even death. WARNING Read this Safety & Operating Instructions manual before you use the Wood Chipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine.
- Page 5 Part I: General Safety Rules Before using the wood chipper NOTICE A． Operators must be fully trained before using this machine. B． User Manual is read and understood. C． Machine is positioned on level ground; all guards are fitted and in good condition. D．...
- Page 6 Part I: General Safety Rules Safety for Children and Pets WARNING Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the machine and the chipping activity. Never assume that children will remain where you last saw them.
- Page 7 Part I: General Safety Rules required, see your authorized dealer for engine governor adjustments. Keep combustible substances away from the engine when it is hot. Never cover the machine while the muffler is still hot. K. Do not operate the engine with the air cleaner or the carburetor air intake cover removed.
- Page 8 Part I: General Safety Rules N. Use the machine only in daylight. O. Stay alert for hidden hazards or traffic. Keep all nuts and bolts tight and keep the equipment in good operating condition. A Note to All Users List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this WOOD CHIPPER in a safe manner.
-
Page 9: Part Ii: Familiar With The Wood Chipper
Part II: Familiar with the Wood Chipper PART II: Familiar with the Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact DK2POWER at 702-331-5353 8-4 PST. TECHNICAL SPECIFICATIONS Recoil Start Electric Start... -
Page 10: Part Iii: Operating The Wood Chipper
Part IV: Maintaining The Wood Chipper PART III: Operating the Wood Chipper It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter. WARNING A. Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules”... - Page 11 Part IV: Maintaining The Wood Chipper Stopping PRESS THE SAFETY SHUT OFF BAR ON THE FEED CHUTE Move the Throttle Lever to IDLE. Recoil Start: Slide the GAS lever to the LEFT to shut engine off. Electric Start: Turn the Key to the OFF position. Operator Zone Wood Chipping NOTICE...
-
Page 12: Part Iv: Maintaining The Wood Chipper
Part IV: Maintaining The Wood Chipper PART IV: Maintaining the Wood Chipper Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. - Page 13 Part IV: Maintaining The Wood Chipper Lubrication NOTICE All Bearings of your Chipper are sealed units and should have enough lubricant to last the life of your machine with normal use. FOR ENGINE WARRANTY CONTACT YOUR NEAREST KOHLER ENGINE DEALER. VISIT WWW.KOHLERENGINES.COM AND ENTER YOU ZIP CODE IN THE FIND A...
-
Page 14: Part V: Troubleshooting And Parts List
Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact DK2POWER in LAS VEGAS at 702-331-5353 8-4 PST WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. - Page 15 Part VI: Troubleshooting and Parts List Explosion View and parts list Ref.No. Description Ref.No. Description Rubber fixer strip Discharge (middle part) Kill switch cover Discharge (top part) Return lever spring Spacer Ø21*Ø25*95 Rubber plate Fore-wheel fixture Emergency stop bar Wheel 4.10-4 Bar fixture(left) Washer Ø16*Ø26*3 M10 lock nut...
- Page 16 Part VI: Troubleshooting and Parts List...
- Page 17 If within one (1) year from the original date of purchase this product fails due to defect in material or workmanship. DK2 POWER outdoor power equipment is 1-year parts only warranty no labor. Upon expiry of one (1) year, Detail K2 will have no further liability related to the product. Detail K2 does not authorize any party, including its authorized distributors or dealers, to offer any other warranty on behalf of Detail K2 Inc.
Need help?
Do you have a question about the OPC566E and is the answer not in the manual?
Questions and answers
need.➢The blades may be dull, reverse to the sharp edge, can you explain this to me p,ease
The context does not provide the specific steps to reverse the blades on a DK2 Power OPC566E. However, it mentions that if the blades are dull, they can be reversed to the sharp edge or replaced. Detailed steps are not included.
This answer is automatically generated