Related Manuals for HTP Invertig 200
Summary of Contents for HTP Invertig 200
- Page 1 America Inc. Invertig 200 AC/DC Owner’s Manual HTP America, Inc. 3200 Nordic Road Arlington Heights, IL 60005-4729 • • 1-800-USA-WELD 847-357-0700 FAX: 847-357-0744 www.usaweld.com • • •...
- Page 2 HTP America, Inc. has reserved the right to make change in design or add any improvements to its products at any time without incurring any obligation to install same on equipment. This warranty is void unless warranty card is sent to HTP America, Inc. within 15 days from date of purchase.
- Page 3 Electrical Connection can fatally shock a person whose body becomes a conductor. Your Invertig 200 AC/DC operates on single-phase 230 volt Do not stand, sit, lie, lean on or touch a wet surface when power [(+/- 15%) 195.5 to 264.5 volts]. The machine is not welding.
-
Page 4: Front Panel Controls
This lamp is illuminated when the On-Off switch on the back of The Digital Display Panel allows you to see what your welding your Invertig 200 is turned to the 1 or "On" position, indicating parameters are. For example, the normal display is the welding the unit is correctly connected to 220 volt AC power. - Page 5 This knob determines the welding amperage. The amperage Invertig 200 AC/DC. on your Invertig 200 can be adjusted from 5 to 200 amps. The amperage is displayed in the digital display panel (#4) when the A) Lift Arc Mode – the lift arc mode allows you to initiate the local/remote switch (#10) is in the local position.
- Page 6 The I2 buttons control the Final Current. This is only By depressing the Pulse Mode button, the green light will applicable when your Invertig 200 is set in the 4T welding illuminate indicating your Invertig 200 is in the pulse mode. At mode.
-
Page 7: Front Panel Connections
AC wave and the negative part of the AC wave are heat that builds up in the torch and shortens tungsten life, equal. Your Invertig 200 allows you to adjust the AC balance decreases penetration, but increases the cleaning portion of from 10% to 90%, a substantially greater range than is possible the wave. -
Page 8: Rear Panel Controls
30 cubic feet per hour (cfh). General Welding Parameters Use a gas regulator such as HTP Part #12020 which is Following are some "rule of thumb" welding parameters compatible with Argon cylinders and has a barbed fitting for the tungsten diameters and amperage settings for welding different delivery hose. -
Page 9: Quick Setup
1/16" thick. If you are welding something 1/4" thick, then you would want to use a larger diameter filler wire than you used when welding 1/16" material, say 1/8" to 5/32". HTP has the following filler wire available in 1 lb tubes which are sealed to prevent oxidation. 4043-1/16-1 4043 Alloy Aluminum Wire 1/16"... - Page 10 Voltage/Amp Curve HTP Invertig 200 Amperage 45.1 57.6 44.6 54.8 53.8 42.2 53.2 40.5 52.7 36.8 52.3 32.8 51.6 29.7 50.6 24.9 21.2 49.7 17.7 48.3 14.8 13.1 46.5 45.9...
- Page 11 SR-17 Air-Cooled Tig Torch Parts Breakdown Tungsten Diameter Illus # Description .040" (1.0mm) 1/16" (1.6mm) 3/32" (2.4mm) 1/8" (3.2mm) Standard Configuration Alumina Nozzle 10N49 10N48 10N47 10N46 Collet Body 10N30 10N31 10N32 10N28 Collet 10N22 10N23 10N24 10N25 Cup Gasket 18GC 18GC 18GC...
- Page 12 SR-20 Water-Cooled Tig Torch Parts Breakdown Tungsten Diameter Illus # Description .040" (1.0mm) 1/16" (1.6mm) 3/32" (2.4mm) 1/8" (3.2mm) Standard Configuration Alumina Nozzle 13N09 13N10 13N11 13N12 Collet Body 13N26 13N27 13N28 13N29 Collet 13N21 13N22 13N23 13N24 Small Gas Lens Configuration Alumina Nozzle 53N59 53N60...
- Page 13 HTP Invertig 200 Spare Parts List Illus # Part # Description Illus # Part # Description 66109 HANDLE 64274 SOCKET 66797 INSULATING PLATE 62500 61457 INDUCTANCE 62483 INTERMEDIATE PANEL 62349 SIDE PANEL 61981 PRIMARY POWER ASSEMBLY 61620 3 WAY ANPHENOL CONNECTOR...
- Page 14 HTP Invertig 200 Parts Breakdown...
- Page 15 Water Cooler Parts Breakdown HANDLE 66184 COVER 62015 RADIATOR 63143 TANK 66302 66303 POMP 64150 FRONT LABEL 66935 RED QUICK ADAPTOR 63147 BLUE QUICK ADAPTOR 63144 FUSE 64207 FUSE HOLDER 64180 BASE 62016 ON / OFF SWITCH 64056 BLUE QUICK ADAPTOR 63145 PRESSURE SWITCH 63146...
- Page 16 HTP Invertig 200 - Wiring Diagram...
- Page 17 HTP Invertig 200 AC/DC Troubleshooting Guide Look inside the machine: do you find any Replace PCB that burst, burnt or blown up parts? has damaged Are any of the wires burnt or damaged? components Which of following problems do Switch machine on...
- Page 18 Is the problem on plug or on board? Do you have a voltage Do you have a voltage Do you have a voltage of 220Vac on input of of 220Vac at input of of 220Vac on input of power cable? switch S1 ? PCB 4? Replace...
- Page 19 Is fuse F1 Go to intact? point C Replace fuse F1 Replace transformer T AUX1 Do you have 3 secondary Do you have voltage of voltages on aux. 230/240Vac on input of transformer T AUX1 transformer T AUX1? (0-9V/0-18V/0-24V)? Go to point I Replace front panel group...
Need help?
Do you have a question about the Invertig 200 and is the answer not in the manual?
Questions and answers