Table of Contents
Advertisement
Manufacturer Manual of NK105 Integrated CNC System
(Applicable to NK105G3 Handheld Box)
1 System overview................................................................................................................................................. 1
1.1 NK105 (E) Control Box with Four Axes ................................................................................. 1
1.1.1 Schematic Diagram .............................................................................................................. 2
1.1.2 Dimension Drawing (Unit: mm) .................................................................................. 3
1.2 NK105G3 Handheld Box.................................................................................................................. 3
1.2.1 Button Definition................................................................................................................... 4
1.2.2 Dimension Drawing (Unit: mm) ............................................................................... 10
1.3 Main Software Interface ............................................................................................................... 10
1.3.1 General NK105 with Four Axes ................................................................................. 11
1.3.2 General NK105 with Double Z Axes ....................................................................... 12
2 Wiring ..................................................................................................................................................................... 13
2.1 Signal Type ........................................................................................................................................... 13
2.1.1 Binary Input Signal ........................................................................................................... 13
2.1.2 Open Collector Output Signal ..................................................................................... 14
2.1.3 Analog Output Signal ....................................................................................................... 14
2.1.4 Differential Output Signal ............................................................................................. 15
2.2 Terminal Definition ......................................................................................................................... 15
3 Basic Commissioning .................................................................................................................................... 16
3.1 Start the System................................................................................................................................. 16
3.2 Select the Axis Mode ....................................................................................................................... 17
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
Author: Product Supporting Department
Weihong Corporation, All Rights Reserved
上海维宏电子科技股份有限公司
Version: 2020.5 1st Version
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for WEIHONG NK105
Summary of Contents for WEIHONG NK105
-
Page 1: Table Of Contents
Author: Product Supporting Department Weihong Corporation, All Rights Reserved 1 System overview..............................1 1.1 NK105 (E) Control Box with Four Axes ................. 1 1.1.1 Schematic Diagram ......................2 1.1.2 Dimension Drawing (Unit: mm) .................. 3 1.2 NK105G3 Handheld Box........................3 1.2.1 Button Definition........................ - Page 2 4.3 Select a WCS ............................27 4.4 Define the Workpiece Origin ..................... 28 4.4.1 General NK105 with Four Axes ................. 28 4.4.2 General NK105 with Double Z Axes ............... 29 4.5 Set the Tool Number ........................30 4.6 Execute Fixed Calibration......................31 4.7 Start Machining..........................
- Page 3 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 5.4 Set the Stop Position ........................39 5.5 Use Array Machining ........................40 5.6 Save the Workpiece Origin ......................41 5.7 Select an Adjacent Point for Machining ................42 6 Parameter Maintenance ..........................43 6.1 Back up Parameters ........................
- Page 4 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8.2 Check Buttons ............................. 57 8.3 Check Input Ports ..........................58 8.4 Check Output Ports.......................... 59 8.5 Check LED Lights ..........................60 9 System Parameters ............................61 9.1 Operator Parameters........................61 9.1.1 Machining Wizard......................61 9.1.2 Velocity.............................
- Page 5 9.2.28 Deceleration Time at Pause ..................88 10 Drive Parameters and Wiring Diagrams ..................89 10.1 Drive Parameters........................... 89 10.2 Wiring Diagrams between NK105(E) Control Box and Different Drives..90 10.2.1 Stepping Drive with Differential Input .............. 90 10.2.2 WISE Servo Drive ......................91...
- Page 6 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2.3 YASKAWA Σ–Ⅱ Servo Drive ..................91 10.2.4 DELTA ASDA Servo Drive ..................92 10.2.5 PANASONIC MINAS_A4 Servo Drive ..............93 10.2.6 MITSUBISHI MR-E Servo Drive ................93 10.2.7 FUJI FALDIC-β Servo Drive ..................94 10.2.8 STONE GS Servo Drive ....................
-
Page 7: System Overview
Interface. 1.1 NK105 (E) Control Box with Four Axes This section introduces the schematic diagram and dimension drawing o f NK105 (E) control box with four axes. This control box, an integration of the system control card, terminal board and other parts, connects to the handheld box with 15-core connecting cable. -
Page 8: Schematic Diagram
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1.1.1 Schematic Diagram This schematic diagram of NK105 (E) control box with four axes is as follows: USB interface It allows NK105 to communicate with other devices. DB15 interface It is used to connect to a handheld box. -
Page 9: Dimension Drawing (Unit: Mm)
About terminal definition of the control box, see Terminal Definition. Note: It is only applicable to NK105 (E) control box with four axes. 1.1.2 Dimension Drawing (Unit: mm) The thickness of NK105 (E) control box with four axes is 218.3mm. -
Page 10: Button Definition
: Arrow button (right). – : It is used to enable / disable the spindle. – : It is used to enter the menu interface, or enter the interface for updating the system image at the time of starting NK105. 4 / 97... - Page 11 : It is used to clear the workpiece coordinates of X-axis and Y- axis at the same time. – • General NK105 with four axes: It is used to clear the workpiece coordinate of Z-axis or A-axis. • General NK105 with double Z axes: It is used to clear the workpiece coordinate of Z1-axis.
- Page 12 : It is used to move Y-axis in the negative direction or input the figure 2. – • General NK105 with four axes: It is used to move Z-axis in the positive direction or input the figure 9. • General NK105 with double Z axes: It is used to move Z1-axis in the positive direction or input the figure 9.
- Page 13 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. – • General NK105 with four axes: It is used to move A-axis in the positive direction or input the figure 7. • General NK105 with double Z axes: It is used to move Z2-axis in the positive direction or input the figure 7.
- Page 14 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. – : It is used to increase the spindle override. – : It is used to decrease the spindle override. – : It is used to move X-axis or Y-axis to the fixed point.
- Page 15 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. – : It is used to make the fine adjustment. • Button combination (Exclusive to General NK105 with double Z axes) – : It is used to clear the workpiece coordinate of Y- axis.
-
Page 16: Dimension Drawing (Unit: Mm)
The dimension drawing of NK105G3 handheld box is as follows: 1.3 Main Software Interface The main software interface differs in axes. General NK105 with four axes and that with three axes are the same, except the axis number, so their main interfaces are similar. -
Page 17: General Nk105 With Four Axes
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1.3.1 General NK105 with Four Axes When general NK105 with four axes starts, the system automatically enters the machining interface in the manual mode (ie. Jog or Step mode). The main interface is as follows: Activated axes The figures refer to the selected WCS. -
Page 18: General Nk105 With Double Z Axes
Operation status – Idle: Default status. – Running – Pause – Stop – Locked: NK105 is locked when the soft limit is triggered. Spindle status and coordinate system – Spindle status • Enabled • Disabled – Coordinate system When the coordinate system turns to show the MCS, this area shows G53;... -
Page 19: Wiring
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2 Wiring Through this section, you can quick know the supported signal types and terminal definition of NK105 (E) control box with four axes, which can help you finish wiring. 2.1 Signal Type The signal types include the following: •... -
Page 20: Open Collector Output Signal
2.1.2 Open Collector Output Signal The output port of NK105 (E) control box with four axes belongs to open controller output, with the maximum output current 50mA. The wiring diagram of the output port connected to a solid-state relay is as follows: 2.1.3 Analog Output Signal... -
Page 21: Differential Output Signal
The format of pulse commands that control drive motion is pulse + direction, negative logic. 2.2 Terminal Definition The terminal definition of NK105 (E) control box with four axes is as follows： 15 / 97... -
Page 22: Basic Commissioning
Through this section, you can quickly know the basic commissioning processes of NK105. To do basic commissioning, do the following: Start the system. Select the axis mode. (General NK105 with double Z axes) Activate the axis. (General NK105 with double Z axes) Adjust the port polarity. Set pulse equivalent. -
Page 23: Select The Axis Mode
. The selection immediately takes effect. 3.3 Activate the Axis This operation is applicable to general NK105 with double Z axes. Z1-axis and Z2- axis are activated at the same time by default. To activate the axis, do the following:... -
Page 24: Adjust The Port Polarity
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.4 Adjust the Port Polarity The polarities of input / output ports in the software are specified in terms of the switch type: • P: Normally closed switches. • N: Normally open switches. -
Page 25: Set Pulse Equivalent
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.5 Set Pulse Equivalent During commissioning, you need to modify pulse equivalent according to the actual situation first before controlling the machine tool. To set pulse equivalent, do the following: To enter the menu interface, press To enter the interface of manufacturer parameters, select 5. -
Page 26: Adjust The Axis Direction
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.6 Adjust the Axis Direction This operation is used to check if the positive direction of each axis is the same with that stipulated by Right Hand Rule, and adjust it if not, so as to avoid damage to the machine tool due to incorrect direction. -
Page 27: Set The Workbench Travel
The workbench travel refers to the valid motion range of a machine tool, namely valid machining ranges of all axes. NK105 sets the upper / lower limit of workbench travel as the soft limit, so the workbench travel needs to be identical with the actual dimension. Otherwise, limit overrun and axis crash may occur. -
Page 28: Set The Machine Origin
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.8 Set the Machine Origin The machine origin, a fixed point, is defined through designing, manufacturing and debugging before the machine tool leaves factory. To set the machine origin, do the following: To enter the menu interface, press To enter the interface of manufacturer parameters, select 5. -
Page 29: Set The Spindle
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.9 Set the Spindle This operation is used to set parameters Spindle NO / OFF Delay, Spindle Speed and Maximum Spindle Speed, so as to control the spindle motor. To set the spindle, do the following: To enter the menu interface, press To enter the interface of manufacturer parameters, select 5. -
Page 30: Quick Start
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4 Quick Start Through this section, you can quick know the machining procedure of NK105, and then start machining. To start machining, do the following: Execute returning to the machine origin. Load a program file. -
Page 31: Load A Program File
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the axis interface, select 1. Back REF Point by pressing , and press Select the target axis by pressing , and press Note: For safety, it is recommended to return Z-axis first, or the prompt Dangerous operation, you’d better home Z first. - Page 32 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the file interface, select 2. USB Files by pressing and press It means the current file is selected. Copy the selected file. Delete the selected file. Load the selected file. The current disk is a USB flash disk.
-
Page 33: Select A Wcs
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. You can also do one of the following for the selected program file in the host or a USB flash disk: • To delete the program file, press • To copy the program file to a USB flash disk or the host, press 4.3 Select a WCS... -
Page 34: Define The Workpiece Origin
The workpiece origin is the origin of all axes in the program file. This operation is used to define the workpiece origin according to the actual position and do clearing before machining. This operation differs in the types of NK105: • General NK105 with four axes •... -
Page 35: General Nk105 With Double Z Axes
To specify the workpiece origin of A-axis, manually move A-axis to the target position and press 4.4.2 General NK105 with Double Z Axes To define the workpiece origin, do the following: To specify the workpiece origins of X-axis and Y-axis, do one of the following: –... -
Page 36: Set The Tool Number
Execute Fixed Calibration. 4.5 Set the Tool Number This operation is applicable to general NK105 with double Z axes. And it is used to set the same tool number for Z1-axis and Z2-axis. To set the tool number, do the following: To enter the menu interface, press To enter the operation interface, select 3. -
Page 37: Execute Fixed Calibration
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4.6 Execute Fixed Calibration This operation is applicable to general NK105 with double Z axes. And it is used to measure the tool on a certain fixed position of the machine tool to reconfirm tool offset. -
Page 38: Start Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4.7 Start Machining This operation is used to start to machine the program file. During machining, to check the current loaded program file, machining time and machining line, press in the main interface: To start machining, press 4.8 Adjust Machining... -
Page 39: Adjust The Spindle Speed
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4.8.2 Adjust the Spindle Speed The spindle speed has 11 gears with the minimum unit 0.1. This operation is used to adjust the spindle speed within 0.5S ~ 1.5S. To adjust the spindle speed, press 4.8.3 Execute the Fine Adjustment... -
Page 40: Handle The Soft Limit
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To return to the main interface, press According to the operation status, do one of the following: – Running status: Keep machining. – Pause status: To continue machining from the pause position, press If machining normally ends or if you start machining after pausing it, the fine adjustment is always valid. -
Page 41: Handle The Hard Limit
Move the machine tool away from the limit position. Character Limit Rls turns to Jog. 5 Common Operations Through this section, you can quick know the common operations of NK105. 5.1 Set the Machining Wizard NK105 supports to machine the rectangular milling face or circle milling face. - Page 42 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the interface of machining wizard, select 2. Prog Wizard by pressing , and press To select a machining method, press → – If you have set related parameters before, to use previous parameter settings, select 2.
-
Page 43: Execute Selective Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. – If it is your first time to set the machining wizard, do the following: Select 1. Params Setting by pressing , press , and set parameters. Note: If parameter Engraving depth is too large, when a program file is loaded, the warning Too many file layers generated. -
Page 44: Parse The Simulation Range
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the interface of selective machining, select 3. Select Line No by pressing , and press The start line is the breakpoint position of the current file and the end line is the last line by default. -
Page 45: Set The Stop Position
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To parse machining ranges, select 4. Machining Info by pressing , and press 5.4 Set the Stop Position This operation is used to set the stop position for the spindle after machining. To set the stop position, do the following: To enter the menu interface, press To enter the operation interface, select 3. -
Page 46: Use Array Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To select the stop mode, select 1. Park Mode by pressing press , and do one of the following: – Select Not Move or To MCS Origin by pressing , and press –... -
Page 47: Save The Workpiece Origin
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the interface of array machining, select 7. Array Process by pressing , and press To enable array machining, select On Array by pressing input 1 and press – 0: Enable array machining. (Default setting) –... -
Page 48: Select An Adjacent Point For Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the operation interface, select 3. Operations by pressing , and press To check the list of workpiece origins, select 8. Origin List by pressing , and press Select the target coordinates by pressing , and press →... -
Page 49: Parameter Maintenance
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the operation interface, select 3. Operations by pressing , and press To start machining from the adjacent point of spindle, select 9. Nearby Process by pressing , and press 6 Parameter Maintenance 6.1 Back up Parameters... -
Page 50: Restore Back-Up Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 6.2 Restore Back-up Parameters Before restoring back-up parameters, ensure you have backed up parameters. Otherwise, the prompt Cannot find the backup file. appears. To restore back-up parameters, do the following: To enter the menu interface, press To enter the interface of parameter maintenance, select 6. -
Page 51: Export Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Select 3. Factory Params by pressing , and press The prompt Restore factory parameters? appears. Note: This operation does not delete the backup file. If you delete all internal parameters due to misoperations, you can restore backup parameters. -
Page 52: Import Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 6.5 Import Parameters This operation is used to import parameters in the USB flash disk to the system, avoiding setting parameters again. To import parameters, do the following: To enter the menu interface, press To enter the interface of parameter maintenance, select 6. -
Page 53: System Maintenance
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7 System Maintenance 7.1 Switch the Language NK105 supports Chinese, English and Polish. To switch the language, do the following: To enter the menu interface, press To enter the interface of system maintenance, select 7. System Upkeep by... -
Page 54: Update The System
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To export the log file, select 2. Export Log by pressing , and press The prompt Log is exported successfully. appears. 7.3 Update the System This operation is used to update the system after deleting the parameter file. -
Page 55: Update The System Application
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To update the system, select Update System by pressing and press In the interface for upgrading the system, according to your need, do one of the following by pressing , and press •... -
Page 56: Update The System Image
7.5 Update the System Image This operation is used to update the operation system by the file of system image if a breakdown occurs when you get NK105, and its updating process lasts about 3 minutes. Before updating the system image, ensure the following: •... -
Page 57: Use Registration
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7.6 Use Registration Before using registration, ensure the following: • The software can normally start. • You have generated a registration code with a registration management tool. About the registration management tool, contact your developer. -
Page 58: Use Writing Numbers
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7.7 Use Writing Numbers This operation is used to write numbers again if the system type does not match with the hardware. Before using writing numbers, prepare a USB flash disk with the updated system in its root directory. -
Page 59: Set Help Interface
The result is bad: Press and, input the registration code again. – The result is good: NK105 automatically restarts. 7.8 Set Help Interface This operation is used to set the delay time of Help interface popping up, and this delay time is an integer within the range -1 & [1 ~ 999999]. If you set it to -1, Help interface does not automatically pop up. -
Page 60: Restart The System
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7.9 Restart the System To restart the system, do the following: To enter the menu interface, press To enter the interface of system maintenance, select 7. System Upkeep by pressing , and press Select 6. -
Page 61: Delete Logs
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7.11 Delete Logs This operation is used to delete logs when the free space of the disk is not adequate. To delete logs, do the following: To enter the menu interface, press To enter the interface of system maintenance, select 7. System Upkeep by... -
Page 62: Modify The Manufacturer Password
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7.13 Modify the Manufacturer Password If you need the manufacturer password, please contact us. To modify the manufacturer password, do the following: To enter the menu interface, press To enter the interface of system maintenance, select 7. System Upkeep by... -
Page 63: System Diagnosis
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8 System Diagnosis 8.1 Check System Information This operation is used to check system information, including the software version, board card number, remaining time and registered times. To check system information, do the following: To enter the menu interface, press To enter the diagnosis interface, select 8. -
Page 64: Check Input Ports
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. To enter the interface of button diagnosis, select 3. Keypress Diag by pressing , and press To check the button, press If the button is damaged, nothing or a wrong button name shows in the display. -
Page 65: Check Output Ports
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Select 4. Inport Diag by pressing , and press – 0 ~ 9 and A ~ F respectively represents input ports GX01 ~ GX16. – ○ represents the polarity is P. – ● represents the polarity is N. -
Page 66: Check Led Lights
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8.5 Check LED Lights This operation is used to check if LED lights on the handheld box are normal. To check LED lights, do the following: To enter the menu interface, press To enter the diagnosis interface, select 8. Diagnosis by pressing , and press To enter the interface for diagnosing LED lights, select 6. -
Page 67: System Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9 System Parameters 9.1 Operator Parameters Operator parameters include the following aspects: • Machining wizard • Velocity • Returning to the machine origin before machining • Z position at pause • Offset •... -
Page 68: Velocity
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Nose Gap • Unit: - • Range: [-, Tool Diameter] • Default value: 0.5 • Effective: Immediately • Description: The distance between two adjacent toolpaths. 9.1.2 Velocity G00 Speed • Unit: mm/min •... -
Page 69: Z Position At Pause
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.4 Z Position at Pause For general NK105 with double Z axes, the following parameters of Z1-axis should be set to the same value with that of Z2-axis . Position Option • Unit: - •... -
Page 70: Offset
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.5 Offset Public Offset • Unit: mm • Range: [-10000, 10000] • Default value: 0 • Effective: Immediately • Description: The public offset of X-axis, Y-axis, Z-axis and A-axis. Work Offset • Unit: - •... -
Page 71: Command
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. SOff in Intevl • Unit: - • Range: Yes ; No • Default value: No • Effective: Immediately • Description: Whether to stop spindle in the cycle interval. 9.1.7 Command G73_G83 Retract •... -
Page 72: Stopping The Spindle
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.8 Stopping the Spindle SOFF at Pause • Unit: - • Range: Yes ; No • Default value: Yes • Effective: Immediately • Description: Whether to stop the spindle when machining pauses. SOff at Stop •... -
Page 73: File
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.10 File Including the following: • DXF File • ENG File • PLT File 9.1.10.1 DXF File Lifting Height • Unit: mm • Range: [0, 99999] • Default value: 5 • Effective: Immediately •... - Page 74 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Bottom Process • Unit: - • Range: Yes ; No • Default value: No • Effective: Immediately • Description: Whether to enable bottom process. Metric Size • Unit: - • Range: Yes ; No •...
- Page 75 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Retract Amount • Unit: mm • Range: [0, 99999999] • Default value: 1 • Effective: Immediately • Description: The retract amount after each feed in high-speed reciprocating chip removal mode. 9.1.10.3 PLT File Lifting Height •...
-
Page 76: Tool Change
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.11 Tool Change ATC Capacity • Unit: - • Range: [1, 20] • Default value: 10 • Effective: Immediately • Description: The capacity of the tool magazine. Current Tool No. • Unit: - •... -
Page 77: Red Light
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.1.12 Red Light Process End Tip • Unit: - • Range: Yes; No • Default value: No • Effective: Immediately • Description: Whether the red light turns on for prompt at process ends. -
Page 78: Manufacturer Parameters
Workbench travel • Tool change travel • Travel limit • Machine origin • Spindle • Rotary axis (General NK105 with double Z Axes) • A-axis (General NK105 with four axes) • Compensation • Presetter thickness • Interpolation algorithm • Arc increment •... - Page 79 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Approach Speed • Unit: mm/min • Range: [Jump Speed, Machining Speed] • Default value: 600 • Effective: Immediately • Description: The feedrate when the tool approaches workpiece during positioning (the distance between the tool and workpiece is smaller than deceleration distance).
- Page 80 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Max Speed • Unit: mm/min • Range: [0, max speed] • Default value: 10000 • Effective: Immediately • Description: The maximum speed of X-axis, Y-axis and Z-axis. Short Seg Spd Lmt • Unit: - •...
- Page 81 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Ref Cir Radius • Unit: mm • Range: [0, 100000] • Default value: 5 • Effective: Immediately • Description: The reference for machining circular workpieces. Ref Cir Speed • Unit: mm/min • Range: [Min Speed of Arc Machining, Machining Speed] •...
- Page 82 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Jump Speed • Unit: mm/min • Range: [Approach Speed, Machining Speed] • Default value: 0 • Effective: Immediately • Description: The maximum speed for the stepper motor at start-up without acceleration. Look Ahead Dis •...
-
Page 83: Axis Output Direction
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. F before Ref • Unit: mm/min • Range: [0.06, max speed] • Default value: 1500 • Effective: Immediately • Description: The maximum manual speed before returning to machine origin. 9.2.2 Axis Output Direction Axis Outp Dir •... -
Page 84: Tool Change Travel
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.5 Tool Change Travel Strk Upper Lmt • Unit: mm • Range: [Lower Limit of Tool Change, 67108.864] • Default value: 400 • Effective: Immediately • Description: The machine coordinate of upper limit of workbench travel during tool change. -
Page 85: Spindle
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. REFP Dir • Unit: - • Range: Positive; Negative • Default value: - • Effective: Immediately • Description: The direction of coarse positioning during returning to machine origin. Retract Dist • Unit: mm •... -
Page 86: Rotary Axis
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.9 Rotary Axis Rotary Axis Type • Unit: - • Range: 0; 1; 2 • Default value: 0 • Effective: Immediately • Description: The type of rotary axes. – 0: Disabled – 1: X-axis –... -
Page 87: A-Axis
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Rotary Axis Acc. • Unit: rad/s • Range: [0.001, 1000000] • Default value: 6.981 • Effective: Immediately • Description: The acceleration of the rotary axis. Max Rotary Vel. • Unit: r/min • Range: [0.006, 6000000] •... -
Page 88: Compensation
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. A Acc. • Unit: rad/s^2 • Range: [0.001, 1000000] • Default value: 6.981 • Effective: Immediately • Description: The acceleration of A-axis. Max A Speed • Unit: r/min • Range: [0.006, 6000000] •... -
Page 89: Presetter Thickness
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.12 Presetter Thickness Cali Thickness • Unit: mm • Range: [0, Workbench Travel] • Default value: 10 • Effective: Immediately • Description: The presetter thickness. 9.2.13 Interpolation Algorithm Algorithm • Unit: - •... -
Page 90: Arc Radius Tolerance
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.15 Arc Radius Tolerance Arc Tolerance • Unit: mm • Range: [0.001, 100000] • Default value: 2 • Effective: Immediately • Description: In the IJK incremental representation of G02 and G03, the radius is calculated twice. -
Page 91: Safety Height
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.18 Safety Height Safety Height • Unit: mm • Range: [0,5000] • Default value: 10 • Effective: After restart • Description: The safety height is calculated with respect to workpiece origin. And the horizontal movement at this height is considered to be safe. This parameter is used in breakpoint resume and returning to workpiece origin. -
Page 92: G00 Feed 100 Percent
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.20 G00 Feed 100 Percent G00 Feed 100% • Unit: - • Range: Yes; No • Default value: Yes • Effective: Immediately • Description: Whether to enable 100% feedrate override for G00. 9.2.21 Smoothing Time Smoothing Time •... -
Page 93: Corner Tolerance
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.23 Corner Tolerance Corner Toler • Unit: s • Range: [0,0.1] • Default value: 0.1 • Effective: Immediately • Description: The corner tolerance. For overall smoothness of workpiece, the tool may not accurately arrive at the specified position at the connection of each two program segments. -
Page 94: Override Acceleration
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9.2.27 Override Acceleration Max Frp Acc • Unit: mm/s^2 • Range: [0.01,10000] • Default value: 1000 • Effective: After restart • Description: The maximum acceleration during override changes. 9.2.28 Deceleration Time at Pause Deceleration •... -
Page 95: Drive Parameters And Wiring Diagrams
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10 Drive Parameters and Wiring Diagrams 10.1 Drive Parameters Drive parameters listed in this section can only make a machine tool normally move, without ensuring machining effects. To get a better machining effects, you need to change the parameter setting according to the specific machine too l. -
Page 96: Wiring Diagrams Between Nk105(E) Control Box And Different Drives
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2 Wiring Diagrams between NK105(E) Control Box and Different Drives 10.2.1 Stepping Drive with Differential Input The wiring diagram is as follows: 90 / 97... -
Page 97: Wise Servo Drive
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2.2 WISE Servo Drive The wiring diagram is as follows: 10.2.3 YASKAWA Σ–Ⅱ Servo Drive The wiring diagram is as follows: 91 / 97... -
Page 98: Delta Asda Servo Drive
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2.4 DELTA ASDA Servo Drive The wiring diagram is as follows: • DELTA ASDA-AB • DELTA ASDA-A 92 / 97... -
Page 99: Panasonic Minas_A4 Servo Drive
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2.5 PANASONIC MINAS_A4 Servo Drive The wiring diagram is as follows: 10.2.6 MITSUBISHI MR-E Servo Drive The wiring diagram is as follows: 93 / 97... -
Page 100: Fuji Faldic-Β Servo Drive
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.2.7 FUJI FALDIC-β Servo Drive The wiring diagram is as follows: 10.2.8 STONE GS Servo Drive The wiring diagram is as follows: 94 / 97... -
Page 101: Legal Notices
The term “Software Product” includes all copies of the licensed software and its documentation. This license agreement is a legal agreement between You (either an individual, a legal entity or any affiliated companies or other entities) and Weihong Electronic Technology Co., Ltd. (hereinafter referred to as Weihong Company). By installing, copying, or otherwise using the Software Product, you agree to be bound by the terms and conditions of this license. -
Page 102: Intellectual Property Rights Notice
Whether you follow other terms in this agreement or not, Weihong Company, as well as its agents and sales staff , will not be responsible for any profits loss, availability loss, business break-off or any forms of... -
Page 103: Applicable Law
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 11.6 Applicable Law: Copyright Law, Regulations for the Protection of Computer Software, Patent Law and other relevant laws and regulations. Now, we affirm that you have already read through this agreement and understood it thoroughly and agreed to comply with all of the terms and conditions of this agreement strictly. - Page 104 S P E C I A L I Z E D / C O N C E N T R A T E D / F O C U S E D Shanghai Weihong Electronic Technology Co., Ltd. Address: No. 1590, Huhang Rd., Fengxian, Shanghai, China, 201401 Hot-line: 400 882 9188 Website: www.weihong.com.cn/en...
Need help?
Do you have a question about the NK105 and is the answer not in the manual?
Questions and answers