1. Manuals
  2. Brands
  3. WEIHONG Manuals
  4. Control Systems
  5. Ncstudio V15
  6. Manual

WEIHONG Ncstudio V15 Manual

Laser cutting
Hide thumbs Also See for Ncstudio V15:
Table of Contents

Advertisement

Quick Links

Manufacturer's Manual of Ncstudio V15 Laser
Cutting (LS6000M) Control System
1 Quick Start ........................................................................................................................ 1
1.1 Overview .................................................................................................................... 1
1.2 Hardware Connection Diagram .................................................................................. 1
1.3 Shortcut Keys ............................................................................................................. 3
2 Install the System ............................................................................................................. 4
2.1 Overview .................................................................................................................... 4
2.2 Install Follow-up Amplifier .......................................................................................... 4
2.3 Install Motion Control Card ......................................................................................... 4
2.4 Install the Software ..................................................................................................... 4
2.5 Install the Drive........................................................................................................... 5
2.5.1 Automatic Installation ........................................................................................... 5
2.5.2 Manual Installation ............................................................................................... 6
3 System Debugging............................................................................................................ 7
3.1 Overview .................................................................................................................... 7
3.2 Configure Settings in NcConfig .................................................................................. 7
3.2.1 Data Backup ........................................................................................................ 8
3.2.2 Data Restoration .................................................................................................. 8
3.2.3 Device and Port Mapping Configuration .............................................................. 8
3.2.4 Port Protection ..................................................................................................... 9
3.3 Modify I/O Port Polarity ............................................................................................ 10
3.4 Set Drive Parameters ............................................................................................... 10
3.4.1 Set Drive Parameters in Non-bus Control Systems ........................................... 11
3.4.2 Set Drive Parameters in Bus Control Systems .................................................. 29
3.5 Set Bus System Parameters .................................................................................... 32
3.6 Set Speed Parameters ............................................................................................. 32
3.7 Set Pulse Equivalent ................................................................................................ 33
3.8 Check Axis Direction ................................................................................................ 34
3.9 Set Workbench Travel Limits ................................................................................... 34
3.10 Set the Screw Error Compensation ........................................................................ 34
3.10.1 Set the Backlash Compensation ...................................................................... 35
3.10.2 Set the Bidirectional Compensation ................................................................. 35
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
Version: 2022.01.14 2nd Version
Author: Product Testing Department
Weihong Corporation All Rights Reserved
Contents
上海维宏电子科技股份有限公司
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ncstudio V15 and is the answer not in the manual?

Questions and answers

Related Manuals for WEIHONG Ncstudio V15

Summary of Contents for WEIHONG Ncstudio V15

  • Page 1: Table Of Contents

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Manufacturer's Manual of Ncstudio V15 Laser Cutting (LS6000M) Control System Version: 2022.01.14 2nd Version Author: Product Testing Department Weihong Corporation All Rights Reserved Contents 1 Quick Start ........................1 1.1 Overview ........................1 1.2 Hardware Connection Diagram ..................
  • Page 2 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3.11 Check Machine Settings ..................37 3.11.1 Pulse Equivalent and Electronic Gear Ratio ............ 37 3.11.2 Pulse ........................ 37 3.11.3 Laser Technic Settings ..................38 3.12 Do a Burn Test ....................... 38 3.13 Install and Use the Camera ..................39 3.13.1 Modify the Computer IP Address ..............
  • Page 3 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.1.2 Extension Terminal Board ................. 61 5.2 Laser ........................63 5.2.1 IPG-YLR Series Laser ..................64 5.2.2 Feibo MARS-500W Laser .................. 64 5.2.3 Raycus Fiber Laser .................... 65 5.2.4 JK / GSI-500W-FL Laser ................... 65 5.2.5 MAX Fiber Laser ....................

  • Page 4: Quick Start

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 1 Quick Start 1.1 Overview This section introduces the hardware and software of the NcStudio V15 laser cutting control system.  Hardware o PM95A motion control card o Lambda controller  Non-bus control systems: Lambda 5E controller ...
  • Page 5 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Bus control systems The connection diagram is shown below: 2 / 116...

  • Page 6: Shortcut Keys

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 1.3 Shortcut Keys The shortcut keys are as follows: 3 / 116...

  • Page 7: Install The System

     Yes: Clean them with an eraser.  No: Replace the control card. 2.4 Install the Software This section introduces how to install the software of the NcStudio V15 laser cutting control system. 4 / 116...

  • Page 8: Install The Drive

    2.5 Install the Drive The corresponding drive matching the software and hardware needs to be installed to install the NcStudio V15 laser cutting control system. The system will perform Automatic Installation during software installation process. If the automation fails, you need to Manual Installation.

  • Page 9: Manual Installation

    Non-first manual drive update: In the left list, click Device Manager. In the right list under motion controller, click the WEIHONG motion controller (PM series) option. 2. Follow the steps below to find the configuration file: a.

  • Page 10: System Debugging

    SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3 System Debugging 3.1 Overview This section gives an overview of the debugging process for the NcStudio V15 laser cutting control system: 3.2 Configure Settings in NcConfig The offline configuration tool NcConfig can be used to backup/restore data, configure devices, and map/protect the ports to improve project development efficiency.

  • Page 11: Data Backup

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Data Restoration o Device and Port Mapping Configuration o Port Protection 3.2.1 Data Backup Follow the steps below to use NcConfig to back data: 1. In the menu bar, go to Systems > Backup and Restore.

  • Page 12: Port Protection

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3. Configure the devices based on your demands: o To add a controller/terminal board, right-click on BusO and select Add controller and select the target controller/terminal board. o To replace a controller/terminal board, right-click on the controller/terminal board to be replaced and click Replace.

  • Page 13: Modify I/O Port Polarity

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 2. Select and click the Configuration type field of the target port and select a protection type in the pull-down menu. 3. Select one from the following methods to save the changes: o To save changes on the current page, click under the menu bar.

  • Page 14: Set Drive Parameters In Non-Bus Control Systems

     2: Velocity control mode o Value: 1  Pr528 LED initial state o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 15 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Description: The number of command pulses for the motor to rotate by one turn o Unit: - o Range  0: Pr009 and Pr010 are effective  Not 0: Pr008 = Screw pitch/(pulse equivalent * mechanical...
  • Page 16 (FnXXX) is not allowed. o Value: 0000  Un00C Input command pulse counter o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 17 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Pn50A Function selection o Description: Function selection o Unit: - o Range  Digit 1: If digit 1 is set to 0, the /S-ON signal is enabled and its input pin is No.40. If digit 1 is set to 7, the /S-ON signal is always ON.
  • Page 18 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3.4.1.1.3 Yaskawa Σ-Ⅴ/Σ-7 The parameters and descriptions are shown below:  Fn010 Parameter input inhibition setting o Description: Parameter input inhibition setting o Unit: - o Range  If Fn010 is set to 0000, modification of user parameters (PnXXX) and some auxiliary function parameters (FnXXX) is allowed.
  • Page 19 The parameters and descriptions are shown below:  Pr01 LED initial state o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 20 The parameters and descriptions are shown below:  Pr5.28 LED initial state o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 21 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  If Pr0.08 is not 0, Pr0.08 = screw pitch/(pulse equivalent × mechanical reduction ratio) o Value: 0  Pr0.09 1st command division and multiplication numerator, Pr0.10 Command pulse division and multiplication denominator o Description: Relation between Pr0.09 and Pr0.10...
  • Page 22 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3.4.1.1.6 Fuji FALDIC-β The parameters and descriptions are shown below:  Command pulse numerator α, 02 Command pulse denominator β o Description: Stand for electronic gear ratio numerator and denominator. o Unit: - o Range: 1–32767...
  • Page 23 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Unit: - o Range  0: Drive parameter values can be modified.  1: Drive parameter values cannot be modified. o Value: 0 or 1  CONT 1 constant validity 1 o Description: CONT 1 constant validity 1 o Unit: - o Range: 1: valid upon servo motor start (RUN).
  • Page 24 The parameters and descriptions are shown below:  P0-02 Drive status display o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 25 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Format: ZYX1X0  Z=0: DIO value does not change when the control mode is switched. Control mode was not switched; therefore, Z=0.  Y=0: Rotates CW (anti-clockwise when observing from the load side).
  • Page 26 The parameters and descriptions are shown below:  P0-02 Drive status display o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 27 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Range: - o Value: 102  P1-01 Control mode setting o Description: Control mode setting o Unit: - o Format: ZYX1X0  Z=0: DIO value does not change when the control mode is switched.
  • Page 28 The parameters and descriptions are shown below:  P0-02 Drive status display o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 29 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  P1-01 Control mode setting o Description: Control mode setting o Unit: - o Format: YX1X0  Y=0: Rotates CW (anti-clockwise when observing from the load side). Y=1: Rotates CCW.  X1X0=00: The control mode is position control.
  • Page 30 The parameters and descriptions are shown below:  P0-02 Drive status display o Description: Pulse detection is used in WEIHONG control systems to check to see if correct pulses are sent and determine if there is electric interference. o Unit: -...
  • Page 31 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Z=0: DIO value does not change when the control mode is switched. Control mode was not switched; therefore, Z=0.  Y=0: Rotates CW (anti-clockwise when observing from the load side). Y=1: Rotates CCW.
  • Page 32 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Description: DO1 pins are pin No.6 and No.7, which are used for Z-axis clamping position braking signals. o Unit: - o Format: X2X1X0  X2=1: Set DO1 output to the NO contact a. X2=1: Set DO4 output to the NC contact b.
  • Page 33 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 2. [Set Station Address](../topic_ls6000/set_driver_para_en.md#set-station-address) 3.4.2.1 Set Common Drive Parameters Two methods are available for you to set the drive parameters:  Drive front panel. For details, see the drive user manual.  NcStudio software.
  • Page 34 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Station address of each axis drive is unique and has to be consistent with the value of the corresponding station address parameter in NcStudio. If its station address parameter is set to 0, the communication function is disabled.

  • Page 35: Set Bus System Parameters

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3. Open NcStudio. Set the axis station address parameters to the values set by the drive front panel. 3.5 Set Bus System Parameters If you are using a bus system, set the bus system parameters.

  • Page 36: Set Pulse Equivalent

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 2. Click the System Parameters tab. Click Speed Accuracy category in the left list to adjust the parameters on the right. 3.7 Set Pulse Equivalent During debugging, you need to adjust the pulse equivalent and electronic gear ratio before starting to control the machine movement.

  • Page 37: Check Axis Direction

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Encoder resolution: The number of pulses required to make the servo motor axis rotate by one turn. Parameters in non-bus systems  Pulse equivalent o The straight distance travelled by the lead screw or the angle turned by the rotary axis when the system sends one pulse.

  • Page 38: Set The Backlash Compensation

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  0: no compensation  1: backlash compensation  2: backlash and unidirectional compensation The compensation is based on the unidirectional data from the laser interferometer and the value of parameter Backlash from the dial indicator.
  • Page 39 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD a. In the Positioning Axis area, select a positioning axis. b. In the Laser Interferometer area, set related parameters, and click Generate. The results automatically show in Location Program area. c. Click Run. The machine tool moves according to the generated positioning program and the system records position data at the measuring points.

  • Page 40: Check Machine Settings

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3.11 Check Machine Settings After debugging is complete, you need to check to see if the machine parameters are set properly:  Pulse Equivalent and Electronic Gear Ratio  Pulse  Laser Technic Settings 3.11.1 Pulse Equivalent and Electronic Gear Ratio...

  • Page 41: Do A Burn Test

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3.11.3 Laser Technic Settings Follow the steps below to check laser technic settings: 1. Check to see if the laser, blow, follow, and burst control ports can control the correct functions. If not, set the control ports again.

  • Page 42: Install And Use The Camera

    During a burn test, to stop it, click Stop. 3.13 Install and Use the Camera When installing the NcStudio V15 laser cutting control system, you can select whether to enable the camera functions for machining monitor and control. Currently, only Hikvision and Dahua Technology cameras are supported.
  • Page 43 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD The IP address first three sections, subnet mask, and default gateway need to be the same as those for the camera. The last section of the IP address needs to be different from that of the camera IP address.
  • Page 44 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD c. The IP address first three sections, subnet mask, and default gateway need to be the same as those for the computer. The last section of the IP address needs to be different from that of the computer IP address.

  • Page 45: Follow Debugging

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 4 Follow Debugging 4.1 Overview This function uses matching between the capacitance and distance to control the Z axis up and down movement so as to keep a fixed distance between the cutter and material with.
  • Page 46 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 4.1.3 Manual Control Area This area is for you to manually control the axis movement. In this area:  Axis direction buttons: Click the axis direction buttons to control the target axis to move in the target direction.
  • Page 47 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD After the Z axis has gone to the mechanical origin, the symbol will be displayed before Z axis in the coordinate area.  Stop: Makes the system stop current movement and enter idle state. You can click this button to interrupt system tasks normally during follow control.
  • Page 48 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 4.1.5.2 Data Chart Area Click the System tab to access this area. Click the pull-down menu in the chart upper right corner to switch between the following charts:  Calibration Data Mapping between the cutter/material capacitance and position during auto- calibration of the cutter is displayed here.
  • Page 49 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD X axis: time; Y axis: capacitance Keep the cutter and material stable. Check the Max Difference value in the chart upper right corner. The larger the value, the larger the interference and the more unstable the capacitance measurement.

  • Page 50: Operations

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD To pause the wave movement, double-click any point on the chart. The icon beside the Y axis top side becomes 4.1.5.3 Follow Parameter Setting Area On the Follow window, click the Param tab to access this area. It displays all parameters related to the follow function.
  • Page 51 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 2. Ensure that Set Drive Parameters and Follow Parameter are set properly. 3. In Step mode, make the Z axis move in the positive or negative direction. Check to see if the Z-axis coordinates change by the step.

  • Page 52: Check The Follow Function

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 3. Optional: To execute automatic calibration, click One Key Calibrate. Note: One-key calibration requires manual calibration being executed first. During automatic calibration: 1. The cutter slows lowers and touches the material board. 2. After it touches the material, it moves up by 5 mm.

  • Page 53: Real-Time State Check

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Real-time State Check  Manual Speed 4.3.1 System Setting Includes the following parameters:  Axis Direction(Z) o Description: Specifies the direction for Z-axis mechanical coordinate increments. Modify the parameter value if you find out during manual operation that the axis movement direction is opposite to that determined by the right hand rule.
  • Page 54 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Follow Height o Description: Indicates the distance between the cutter and material plate during follow control. o Range: 0 mm–30 mm o Value: 1  Z UP Pos. o Description: Indicates the mechanical coordinate you want the Z axis to stop at after the Z axis go to the mechanical origin and the follow/machining is complete.
  • Page 55 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Description: Available in velocity control mode. The value is generated after servo drive calibration. o Range: -255–255 o Value: 0  Part Touching Delay (Positioning) o Description: Indicates the part touching delay during positioning.
  • Page 56 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Nonmetal Calibration o Description: Specifies the type of material to be calibrated. o Range  Yes: Non-metal materials, such as wood or glass.  No: Metal materials. o Value: No  Touch Part Capacitance...

  • Page 57: Common Problems

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Value: 6000 4.3.6 Real-time State Check Includes the following parameters:  Detect Out-margin o Description: Indicates whether to enable out-of-edge detection during following. Axis movement will be stopped if the system detects that it has exceeded the edge.
  • Page 58 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 4.4.1 Serious Electric Interference Reason  The position of the servo drive creates some interference.  The shielding layer has been damaged or entangled on the external iron frame.  There is no conductivity between the No.4 pin of the M16 three-core aviation plug towline cable and the amplifier.

  • Page 59: Results Are Normal

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Calibration is not executed after replacing the ceramic ring or nozzle, or the ceramic ring/nozzle is not installed properly, causing large capacitance changes during blowing and certain deviation of the capacitance curve. Solution Follow the steps below to help troubleshoot: 1.

  • Page 60: Follow In-Position Waiting Timeout

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Follow the steps below to help troubleshoot:  Modify the encoder direction parameter and see if the alarm disappears. If not, undo the encoder direction modification and modify the axis rotation direction.  If both the axis direction and encoder direction are incorrect, reverse both the encoder direction and axis rotation values.

  • Page 61: System Reports Material Collision Alarm When The System Has No Movement

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD b. Ensure that the capacitance change during blowing is less than 50. 4. If the alarm is still reported, increase the servo drive gain as needed. 4.4.12 System Reports Material Collision Alarm when the System Has No Movement Reason The current capacitance is equal to or smaller than the Touch Part Capacitance value.

  • Page 62: Wiring

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5 Wiring 5.1 Controller and Terminal Board This section introduces the port definitions of the Lambda controllers and extension terminal board. 5.1.1 Lambda Controller Different Lambda controllers need to be used based on the system type: ...
  • Page 63 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Lambda NE The port definitions are shown below: 60 / 116...

  • Page 64: Extension Terminal Board

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.1.2 Extension Terminal Board The port definitions of EX33A and EX31A extension terminal boards are the same in bus or non-bus control systems. EX33A extension terminal board The port definitions are shown below:...
  • Page 65 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Output working voltage: 24V.  Port COM: 0V output.  Rated current: 200 mA.  Darlington transistor. EX31A extension terminal board The port definitions are shown below: 62 / 116...

  • Page 66: Laser

    Before connecting the laser, do the following preparation:  Connect to applicable pulse modulation signals based on the laser. The pulse modulation signals provided by the NcStudio V15 laser cutting control system and the corresponding EX33A ports are shown below: o +24V single-ended signal: MOD(24V) &...
  • Page 67 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  HFB 1000-1500W laser  GW SMATLas 3S laser Note: All MOD pins of EX33A extension terminal boards shown in the following diagrams are MOD(24V). 5.2.1 IPG-YLR Series Laser The wiring diagram is shown below: 5.2.2 Feibo MARS-500W Laser...

  • Page 68: Raycus Fiber Laser

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.2.3 Raycus Fiber Laser The wiring diagram is shown below: 5.2.4 JK / GSI-500W-FL Laser The wiring diagram is shown below: 65 / 116...

  • Page 69: Max Fiber Laser

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.2.5 MAX Fiber Laser The wiring diagram is shown below: 66 / 116...

  • Page 70: Spi-500W-R4 Laser

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.2.6 SPI-500W-R4 Laser The wiring diagram is shown below: 5.2.7 HFB 1000-1500W Laser The wiring diagram is shown below: 67 / 116...

  • Page 71: Gw Smatlas 3S Laser

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.2.8 GW SMATLas 3S Laser The wiring diagram is shown below: 68 / 116...

  • Page 72: Wiring Diagram Of The Drive

    SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3 Wiring Diagram of the Drive This section introduces how to connect WEIHONG DB15 drive port to different brands of servo motors. Drive wiring methods may vary based on the control mode. Check the drive port definition before referring to the following wiring diagrams: ...
  • Page 73 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Descriptions of the holes and signals are as follows: Signal Definition Input/Output Remark A+, A- Feedback signal of Input It is used to receive the encoder phase A differential output of Differential signal...

  • Page 74: Wiring Diagram Of The Drive (In Position Control Mode)

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Signal Definition Input/Output Remark Differential signal transmission mode INTSPD2 Internal command Output speed option 2 Speed zero clamp Output In speed zero clamp detection signal detection status, the output transistor is turned V-REF...
  • Page 75 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  With brake lines (50P HD plug) 72 / 116...
  • Page 76 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Without brake lines (50P HD plug) 73 / 116...
  • Page 77 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.2 Wiring Diagram of YASKAWA Σ- Ⅱ /Σ- Ⅴ /Σ-7 Servo Drive The wiring diagram is as follows:  Common: 74 / 116...
  • Page 78 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  One-to-two: 75 / 116...
  • Page 79 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.3 Wiring Diagram of Panasonic Servo Drive Wiring diagram is as follows:  Common: 76 / 116...
  • Page 80 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.4 Wiring Diagram of Fuji Servo Drive Wiring diagram is as follows:  Common: 77 / 116...
  • Page 81 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Fuji alpha5 plus (axis X/Y1/Y2) 78 / 116...
  • Page 82 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.5 Wiring Diagram of Delta Servo Drive Delta ASDA-A, ASDA-B, ASDA-B (one-to-two), and ASDA-B2 servo drives use the same type of cables. Wiring diagrams are as follows:  Delta ASDA-A 79 / 116...
  • Page 83 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Delta ASDA-B 80 / 116...
  • Page 84 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Delta ASDA-B (one-to-two) 81 / 116...
  • Page 85 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Delta ASDA-B2 5.3.2.6 Wiring Diagram of Mitsubishi Servo Drive Wiring diagrams are as follows:  MR-JE (without brake cable) 82 / 116...
  • Page 86 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  MR-JE (with brake cable) 83 / 116...
  • Page 87 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 84 / 116...
  • Page 88 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  MR-E 5.3.2.7 Wiring Diagram of Sitong Servo Drive The wiring diagram is as follows: 85 / 116...
  • Page 89 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.8 Wiring Diagram of Hitachi Servo Drive The wiring diagram is as follows: 86 / 116...
  • Page 90 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.9 Wiring Diagram of Teco Servo Drive Wiring diagrams are as follows:  TSDA 87 / 116...
  • Page 91 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  ESDA 88 / 116...
  • Page 92 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.10 Wiring Diagram of Sanyo Servo Drive Wiring diagrams are as follows:  PY series 89 / 116...
  • Page 93 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  R series 90 / 116...
  • Page 94 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.2.11 Wiring Diagram of Kaitong KT270 Series Servo Drive The wiring diagram is as follows: 91 / 116...

  • Page 95: Wiring Diagram Of The Drive (In Velocity Control Mode)

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.3 Wiring Diagram of the Drive (in Velocity Control Mode) 5.3.3.1 Wiring Diagram of WISE Servo Drive Wiring diagrams are as follows:  With brake lines (44P interface) 92 / 116...
  • Page 96 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  With brake lines (50P HD plug) 93 / 116...
  • Page 97 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Without brake lines (44P interface) 94 / 116...
  • Page 98 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.3.2 Wiring Diagram of YASKAWA Σ-5/Σ-7 Servo Drive The wiring diagram is as follows: 95 / 116...
  • Page 99 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.3.3 Wiring Diagram of Fuji Servo Drive Wiring diagrams are as follows:  Common: 96 / 116...
  • Page 100 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Parameter description: o PA1-01  Name: Control mode selection  Value: 1  Description: Velocity control o PA1-08  Name: Number of pulse output per turn  Value: 2500  Description: Set it to 2500 if the pulse equivalent is 0.001, screw pitch is 10 mm, and there is no speed reducer.
  • Page 101 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.3.4 Wiring Diagram of HCFA Servo Drive Wiring diagram is as follows: 98 / 116...
  • Page 102 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Parameter description:  P00.01 o Name: Control mode selection o Value: 1 o Description: Velocity control  P00.02 o Name: Automatic adjustment o Value: 1 o Description: If it is set to 0, real-time auto-adjustment is disabled. If it is set to 1, standard auto-adjustment is enabled without gain switching.
  • Page 103 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  P05.00 o Name: AI1 minimum input o Value: -10 o Range: -10.00V–10.00V  P05.01 o Name: Rotational speed matching AI1 minimum input o Value: -100 o Description: 100% speed matches the system maximum rotational speed.
  • Page 104 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 5.3.3.5 Wiring Diagram of Panasonic Servo Drive Wiring diagram is as follows: 5.3.3.6 Wiring Diagram of Delta Servo Drive Delta ASDA-A and ASDA-B2 servo drives use the same type of cables. Wiring diagrams are as follows: ...
  • Page 105 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD  Delta ASDA-B2 102 / 116...
  • Page 106 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Parameter description:  P0-00: o Name: Drive status display o Range: - o Value: 2 o Description: Set this parameter to monitor the number of pulses sent and received and see if there is electric interference.
  • Page 107 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Name: Electronic gear ratio numerator N1 o Range: 1–32767 o Value: - o Description: N1/M = Encoder pulse number * 4 * pulse equivalent * mechanical reduction ratio/screw pitch. Typical value: If the encoder pulse number = 4000, pulse equivalent = 0.001, screw pitch = 5mm, and...
  • Page 108 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Value: 0 o Description: DI6 are DI7 NC position limit signal input by default. The drive does not work if not connected to CN1 pin No.32 and No.31.  X2=0: Set DI6 and DI7 to the NC contact b.
  • Page 109 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD Parameter description:  H0200 o Name: Control mode o Value: 0  H0203 o Name: Output pulse phase o Value: 1  H0206 o Name: Fault stop and zero-speed stop o Value: 0 ...
  • Page 110 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD o Value: 1  H0901 o Name: Rigidity level o Value: 18  H0502 o Name: Pulse number per turn o Value: 10000 5.3.3.8 Wiring Diagram of Mitsubishi Servo Drive The wiring diagram is as follows:...

  • Page 111: Wireless Handwheel

    6 Wireless Handwheel WHB05 Series Wireless CNC Handwheel is a series of wireless handwheels that can make the machine tools do specified actions through WEIHONG CNC control system. The wireless CNC handwheel is independently designed by WEIHONG Company (short for Weihong Electronic Technology Co., Ltd.) with copyright and manufactured by a third-party...
  • Page 112 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD The button definitions are shown below: 109 / 116...

  • Page 113: Whb05L(V5)

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 6.2 WHB05L(V5) WHB05L(V5) is an upgrade of WHB05L(V4), which replaces the button text with images to demonstrate the functions more vividly. The WHB05L(V5) rotary axis is axis B. Its structure is shown below:...
  • Page 114 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD The button definitions are shown below: 111 / 116...
  • Page 115 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 112 / 116...

  • Page 116: Whb05N(V1)

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 6.3 WHB05N(V1) WHB05N(V1) is a dedicated handwheel for Phoenix tube cutting systems. The WHB05N(V1) rotary axis is axis B. Its structure is shown below: The button definitions are shown below: 113 / 116...
  • Page 117 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 114 / 116...

  • Page 118: Specifications

    上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD 6.4 Specifications Electric parameters  Working voltage & current (handheld device): 3V / 6 mA (two AA batteries)  Low voltage alarm (handheld device): < 2.2V  Transmitting power (handheld device): 14 dB ...

  • Page 119: Legal Notices

    Weihong Company can update the Software Product at any time. You can pay real-time attention to Weihong Company's official website. Termination This license may be terminated by Weihong Company at any time once you violate any terms or conditions made in this agreement. Once the license is terminated, you are 116 / 116...
  • Page 120 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD obliged to destroy all the copies of the Software Product or return them to Weihong Company. Now, we affirm that you have already read through this agreement and understood it thoroughly and agreed to comply with all of the terms and conditions of this agreement strictly.
  • Page 121 S P E C I A L I Z E D / C O N C E N T R A T E D / F O C U S E D Shanghai Weihong Electronic Technology Co., Ltd. Address: No. 1590, Huhang Rd., Fengxian, Shanghai, China, 201401 Hot-line: 400 882 9188 Website: www.weihong.com.cn/en...

This manual is also suitable for:

Ls6000m

Table of Contents

Save PDF