Table of Contents
Advertisement
How to change the door opening
H O W T O C H A N G E T H E D O O R O P E N I N G
This appliance has reversible doors but is delivered with a right hinged door. The left hand
hinge kit comes with the unit (in the box), should you wish to reverse the hinge on your unit.
1. Lower hinge (Right)
This appliance has reversible doors but is delivered with a right hinged door. The left hand
2 . Screws
4. Door
5. Top hinge (Right)
hinge kit comes with the unit (in the box), should you wish to reverse the hinge on your unit
7. Top hinge (Left)
8. Hole cover
follow the directions below:
10. Door limit device
11. Screw
1. Open the door to a 90 degrees angle, take out the 2 screws (2) from lower door axis (3),
1. Open the door to a 90 degrees angle, take out the 2 screws (2) from lower door axis (3),
remove the door (4), Remove the axis plate (3) from the door, (Fig. A).
emove the door (4), Remove the axis plate (3) from the door, (Fig. A).
2. Unscrew the screw (11) located underneath the door frame and the limit device (10), and
2. Unscrew the screw (11) located underneath the door frame and the limit device (10), and
relocate it at left end side of the door frame. (Fig. A/B)
elocate it at left end side of the door frame. (Fig. A/B)
3. Take out the 3 hinge screws (6) from the top hinge (right) (5) and remove it. (Fig. C)
3. Take out the 3 hinge screws (6) from the top hinge (right) (5) and remove it. (Fig. C)
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge (Left) (7) at
4. Remove decorative nail (8) from left top of cabinet and install spare top hinge (Left) (7) at
eft top of cabinet with 3 screws. (Fig. D)
left top of cabinet with 3 screws. (Fig. D)
5. Following the above procedure, install the spare lower hinge to the left (9). (Fig. E)
6. Install and aligned the door.
5. Following the above procedure, install the spare lower hinge to the left (9). (Fig. E)
7. Insert the plastic caps to cover the holes(8).
6. Install and aligned the door.
7. Insert the plastic caps to cover the holes(8).
12
Instruction manual Wi156 Wi157
3 .Door axis
6. Hinge Screws
9. Lower hinge (Left)
1. Lower hinge (Right)
2 . Screws
3 .Door axis
4. Door
5. Top hinge (Right)
6. Hinge Screws
7. Top hinge (Left)
8. Hole cover
9. Lower hinge (Left)
10. Door limit device
11. Screw
Please keep this instruction manual for future reference
I N S T A L L I N G T H E H A N D L E
Remove the door gasket on the drilled holes side to install the handle (see below drawing).
Fix the handle to the screws and push the gasket back into place.
Visit our caple website to view a 'How to video' at
I N S T A L L I N G T H E F U L L H E I G H T P L I N T H G R I L L E
Take out the full height plinth grille and the brackets from the accessories box. Fix the brackets
to the cabinet with screws provided and fix both sides of the grille to the brackets with the 2
supplied screws as shown in below diagram.
Please keep this instruction manual for future reference
WWW.CAPLE.CO.UK
Scan the QR code below to
access the 'How to video'
To be installed
NOTE:
with a 150mm plinth
height.
If you wish to reduce
your plinth height, the
smaller, slot-on plinth
grille (see page 14)
should be used.
Instruction manual Wi156 Wi157
13
Advertisement
Table of Contents
