Water Right Impression Plus Series Installation Instructions & Owner's Manual

Metered water softeners

Hide thumbs Also See for Impression Plus Series:

Installation instructions & owner's manual (36 pages)

Installation instructions & owner's manual (32 pages)

Installation instructions & owner's manual (28 pages)

Table Of Contents

Installation Instructions & Owner's Manual

Impression Plus Series

Metered Water Softeners

For Certified Models:

• IMP-844

• IMP-948

• IMP-1044

• IMP-1054

• IMP-1248

• IMP-1354

Certified Cabinet

Models:

• IMPC-835

• IMPC-1035

Table of Contents

Summary of Contents for Water Right Impression Plus Series

Page 1 Installation Instructions & Owner’s Manual Impression Plus Series ® Metered Water Softeners For Certified Models: • IMP-844 • IMP-948 • IMP-1044 • IMP-1054 • IMP-1248 • IMP-1354 Certified Cabinet Models: • IMPC-835 • IMPC-1035...
Page 2: Table Of Contents
TABLE OF CONTENTS Pre-Installation Instructions for Dealers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Bypass Valve .
Page 3 PRE-INSTALLATION INSTRUCTIONS The manufacturer has preset the water treatment unit’s sequence of cycles, cycle times, salt dose, exchange capacity and salt dose refill time. THE DEALER SHOULD... THE INSTALLER SHOULD... THE HOMEOWNER SHOULD... •Read this page and guide the installer •Program installer settings including hardness, •Read Programming Procedures section.
Page 4: Bypass Valve
BYPASS VALVE The bypass valve is typically used to isolate the control valve from the plumbing system’s water pressure in order to perform control valve repairs or maintenance. The 1” full flow bypass valve incorporates four positions, including a diagnostic position that allows a service technician to have pressure to test a system while providing untreated bypass water to the building.
Page 5: Installation
INSTALLATION GENERAL INSTALLATION & SERVICE WARNINGS The control valve, fittings and/or bypass are designed to accommodate minor plumbing misalignments. There is a small amount of “give” to properly connect the piping, but the water treatment unit is not designed to support the weight of the plumbing. Do not use Vaseline, oils, other hydrocarbon lubricants, or spray silicone anywhere.
Page 6 INSTALLATION 8. INSTALLING GROUND: To maintain an electrical ground in metal plumbing of a home’s cold water piping (such as a copper plumbing system), install a ground clamp or jumper wiring. GROUND STRAP NOTE: If replacing an existing unit, also replace the ground clamps/wire. If removing a unit, replace the piping with the same type of piping as the original to assure plumbing integrity and grounding.
Page 7 This page intentionally left blank.
Page 8: Programming Procedures
PROGRAMMING PROCEDURES 1 . Set Time of Day Typically, time of day should only need to be set after extended power outages or when daylight saving time begins or ends or after the battery has been replaced. If an extended power outage occurs, the time of day will flash on and off indicating that the time should be reset. To set the clock: STEP 1 –...
Page 9: Startup Instructions
FOR DOWNFLOW REGENERATING UNITS STARTUP INSTRUCTIONS FLUSHING OF SYSTEM: To flush the system of any debris and air after installation is complete, please perform the following steps: 1. Rotate bypass handles to the bypass mode (Fig. 2 on page 4) . 2.
Page 10: Operating Displays And Maintenance
OPERATING DISPLAYS AND MAINTENANCE 1 . GENERAL OPERATION: When the system is operating, one of five displays may be shown and will alternate with the installing dealer’s name and phone number for future service. Pressing NEXT will alternate between the displays. 1.
Page 11 OPERATING DISPLAYS AND MAINTENANCE 4 . POWER LOSS AND BATTERY REPLACEMENT: If an extended power outage occurs, the control valve will retain the time of day settings until the board’s battery is depleted. Once the battery is depleted, the display will appear dark and absent of any information. If this occurs, following these steps will determine if the problem is a low battery or a board failure.
Page 12: Troubleshooting Guide
TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION A. Depleted battery. A. See Operating Display and Maintenance section. B. Control valve power adapter not plugged into outlet B. Plug power adapter into outlet or connect or power cord end not connected to PC board power cord end to PC board connection.
Page 13 TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION A. Turn bypass handles to place bypass in A. Bypass valve in bypass position. service position. 7 . Control valve does B. Meter is not connected to meter connection on PC B. Connect meter to three pin connection labeled not regenerate board.
Page 14 TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION A. Injector is plugged. A. Remove injector and replace. B. Faulty regenerant piston. B. Replace regenerant piston. C. Regenerant line connection leak. C. Inspect regenerant line for air leak. 12 . Control valve fails to D.
Page 15 TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION 16 . E3, Err – 1003, A. Snap drive bracket in properly then Press Err – 103 = Control A. Drive bracket not snapped in properly and out NEXT and REGEN buttons for 3 seconds to valve motor ran enough that reduction gears and drive gear do not resynchronize software with piston position...
Page 16 TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION 21 . Err – 201 200 errors are only A. Invalid regeneration cycle step detected. A. Replace PC board. viewable in history screens. These do not flash when error occurs. A. Short power disruption. A. Check transformer voltage and verify power source. 22 .
Page 17: Replacement Parts
REPLACEMENT PARTS FRONT COVER AND DRIVE ASSEMBLY Item # Part # Description Qty . CV3540-A Black Impression cover ® CV3540-W-A Gray Impression cover ® CV3540P-A Black Impression Plus cover ® CV3540P-W-A Gray Impression Plus cover ® CV3107-1 Motor Assembly CV3002-A Drive assembly (includes #5 and #6) CV3579WI-03 PC board, Impression ®...
Page 18 REPLACEMENT PARTS PISTON ASSEMBLY Item # Part # Description Qty . CV3005-02 1” spacer stack assembly CV3430-01 1.25” spacer stack assembly CV3004 Drive cap assembly CV3135 O-ring 228 (drive cap o-ring) CV3011 1” piston assembly downflow CV3011-01 1” piston assembly upflow CV3407 1.25”...
Page 19 REPLACEMENT PARTS BYPASS VALVE Item No. Part No. Description Qty. CV3006 Bypass assembly CV3147 Bypass handles BRINE ELBOW ASSEMBLY Item No. Part No. Description Qty. CV3195-01 Refill port plug assembly Loosens Injector And Bypass Caps CH4615 Elbow locking clip CV4144 3/8”...
Page 20 REPLACEMENT PARTS INJECTOR ASSEMBLIES Item No. Part No. Description Qty. CV3176 Injector cap CV3152 O-ring 135 CV3177-01 Injector screen CV3010-1Z Injector assembly plug CV3010-1A A injector assembly, �� CV3010-1B B injector assembly, �� CV3010-1C C injector assembly, �� CV3010-1D D injector assembly, �� CV3010-1E E injector assembly, ��...
Page 21 REPLACEMENT PARTS DRAIN LINE ASSEMBLY 3/4” DRAIN LINE ASSEMBLY 1” Item No. Part No. Description Qty. Item No. Part No. Description Qty. CH4615 Elbow locking clip CH4615 Elbow locking clip CPKP10TS8-BULK Optional insert, 5/8” tube CV3166 Drain FTG body 1 CV3192 Optional nut, 3/4”...
Page 22 REPLACEMENT PARTS BRINE TANK ASSEMBLY Item No. Part No. Description Qty. CG2191-84 Brine tank cover, injection molded WR CG2180 Brine tank cover, standard CH1095-01 Optional 18” diameter salt grid CH1080 Optional 24” diameter salt grid CG21833CB1C00 18” x 33” brine tank, black CG21840CB1C00 18”...
Page 23 REPLACEMENT PARTS LOW PROFILE CABINET AND BRINE TANK Item No. Part No. Description Qty. CJ2TCWSLP-C Top Assembly Black CJ2B35E Bottom Assembly Light Gray with 474 Brine Assembly Brine Well with Brine Well 474 Assembly 34 5 / 8 ” Not shown CH4850-34.625 HIGH PROFILE CABINET AND BRINE TANK Item No.
Page 24: Installation Fitting Assemblies
INSTALLATION FITTING ASSEMBLIES NOTE: Not all available ﬁ ttings are Item No . Part No . Description Qty . displayed below. Contact For All Assemblies CV3151 Nut, 1” quick connect manufacturer for optional CV3150 Split ring ﬁ ttings. CV3105 O-ring 215 1”...
Page 25: Specifications
Impression Plus Series Specifications SPECIFICATIONS IMP SPECIFICATIONS IMP-844 IMP-948 IMP-1044 IMP-1054 IMP-1248 IMP-1354 MODEL Minimum 13,700 @ 3.4 18,200 @ 4.5 18,200 @ 4.5 27,600 @ 7.0 36,400 @ 9.0 45,800 @ 11.5 Rated Softener Capacity:* Medium 16,800 @ 6.0 23,500 @ 9.0...
Page 26: Warranty
Water Softener Limited Warranty Congratulations. You have purchased one of the nest water treatment systems available. In the unlikely event of a problem due to defects in material and workmanship, we proudly warrant our water softeners to the original owner, when installed in accordance with Water-Right speci cations.
Page 27: Quick Reference Guide
QUICK REFERENCE GUIDE GENERAL OPERATION ERROR When the system is operating, one of four displays will be shown: If the display toggles between “Error” CALL FOR SERVICE 1. Time of day/gpm and an error code (i.e. a number), call a ERROR 2.

This manual is also suitable for:

Imp-844 Imp-948 Imp-1044 Imp-1054 Imp-1248 Imp-1354 ... Show all

Water Right Impression Plus Series Installation Instructions & Owner's Manual

Table of Contents

Related Manuals for Water Right Impression Plus Series

Summary of Contents for Water Right Impression Plus Series

This manual is also suitable for:

Table of Contents