Download
Share
Print this page
Max HN75 Quick Start Manual
  1. Manuals
  2. Brands
  3. Max Manuals
  4. Power Tool
  5. HN75
  6. Quick start manual

Max HN75 Quick Start Manual

High pressure coil nailer
Hide thumbs

Advertisement

Quick Links

Download this manual
HIGH PRESSURE COIL NAILER
1. SAFETY INSTRUCTIONS ..................................4
TECHNICAL DATA .............................................7
AIR SUPPLY AND CONNECTIONS ...................9
3.
4. INSTRUCTIONS FOR OPERATION................. 10
5. MAINTAIN FOR PERFORMANCE ................... 15
6. STORING.......................................................... 15
7. TROUBLESHOOTING/REPAIRS ..................... 15
OPERATING and MAINTENANCE MANUAL
BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING
AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE
ENGLISH
HN75
INDEX
!
WARNING:
.

Advertisement

loading

Related Manuals for Max HN75

Summary of Contents for Max HN75

  • Page 1: Table Of Contents

    ENGLISH HN75 HIGH PRESSURE COIL NAILER INDEX 1. SAFETY INSTRUCTIONS ........4 2. SPECIFICATIONS & TECHNICAL DATA ..........7 AIR SUPPLY AND CONNECTIONS ....9 4. INSTRUCTIONS FOR OPERATION....10 5. MAINTAIN FOR PERFORMANCE ....15 6. STORING............15 7. TROUBLESHOOTING/REPAIRS ..... 15...

  • Page 2: Safety Instructions

    1. SAFETY INSTRUCTIONS WARNING: TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING "SAFETY INSTRUCTIONS". FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR SERIOUS INJURY. PRECAUTIONS ON USING THE TOOL 1.
  • Page 3 8. INSPECT SCREW TIGHTNESS Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put into operation. Inspect to confirm that all screws and bolts are tight and properly installed prior to operating the tool. 9.
  • Page 4 Keep the tool in a dry place out of reach of children when not in use. Do not use the tool without Safety Warning label. Do not modify the tool from original design or function without approval by MAX CO., LTD.

  • Page 5: Specifications

    Cylinder Cap Contact Arm Nose Magazine Trigger Grip Exhaust Cover Trigger Lock Dial 2. TOOL SPECIFICATIONS PRODUCT NO. HN75 12-3/4” (323 mm) HEIGHT 5” (129 mm) WIDTH 11-1/2” (294 mm) LENGTH 5.3 lbs. (2.4 kg) WEIGHT RECOMMENDED 170 to 320 p.s.i. (12 to 23 bar)

  • Page 6: Technical Data

    4. TECHNICAL DATA NOISE A-weighted single-event ------ LWA, 1s, d 97.74 dB sound power level A-weighted single-event ------ LpA, 1s, d 89.82 dB emission sound pressure level at work station These values are determined and documented in accordance to EN12549 : 1999. VIBRATION Vibration characteristic value = 4.07 m/s These values are determined and documented in accordance to ISO 8662-11.

  • Page 7: Air Supply And Connections

    In order to improve its performance, it has set its working pressure higher than the conventional nailers. To use the tool, you always need the special air compressor and air hose (MAX PowerLite Compressor and MAX PowerLite Hose). Use of high-pressure gas (for example, oxygen, acetylene, etc.) causes abnormal combustion, possibly resulting in...

  • Page 8: Instructions For Operation

    4. INSTRUCTIONS FOR OPERATION Read section titled "SAFETY INSTRUCTIONS". 1. BEFORE OPERATION Wear Safety Glasses or Goggles. Do not connect the air supply. Inspect screw tightness. Check operation of the contact arm & trigger if moving smoothly. Connect the air supply. Check the air-leakage.
  • Page 9 Nail loading: Place a coil of nails over the Nail Post in the Magazine. Uncoil Slot enough nails to reach the Feed Pawl, and place the second nail Feed Pawl between the teeth on the Feed Pawl. The nail heads fit in slot on Nose.
  • Page 10 SEQUENTIAL TRIP The Sequential Trip requires the operator to hold the tool against the work before pulling the Trigger. This makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications. The Sequential Trip allows exact fastener location without the possibility of driving a second fastener on recoil, as described under “Contact Trip”.
  • Page 11 DRIVING DEPTH ADJUSTMENT DIAL Adjustment Dial Adjust Spacer WARNING: ALWAYS disconnect air supply before adjustment dial. With air pressure set, drive nails into a representative material Deeper Shallow sample to determine if adjustment is necessary. If adjustment is required, disconnect air supply. Refer to the mark on the Adjust Spacer for direction to turn the adjustment dial.
  • Page 12 WHEN USING THE TOOL FOR STEEL PLATES WARNING: ● Carry out work based on the required Work Standards. ● If there is no specified work standard, refer the following as a reference. ● Never use the nails for the ceilings (ceiling foundations included) or roofs (roof foundations included).

  • Page 13: Maintain For Performance

    All quality tools will eventually require servicing or replacement of parts because of wear from the normal use. 7. TROUBLE SHOOTING/REPAIRS The troubleshooting and/or repairs shall be carried out only by the MAX CO., LTD.authorised distributors or by other specialists.
  • Page 14 6-6 NIHONBASHI-HAKOZAKI-CHO, CHUO-KU, TOKYO, JAPAN Tel: (03) 3669-8131 Telefax : (03) 3669-7104 http://www.maxusacorp.com (USA Site) http://www.max-ltd.co.jp/int/ (GLOBAL Site)
  • Page 15 - nella chiusura di casse o gabbie - nell’ applicazione de assicurazioni per il trasporto, p.e. su veicoli e vagoni. Ergänzung zur Betriebsanleitung von MAX-Naglern Suplemento a la instrucción para la Unter der am O1 Januar 2001 in Kraft tretenden operación europäischen Norm EN 792-13 müssen...