Related Manuals for Reflex Fillcontrol Plus
Summary of Contents for Reflex Fillcontrol Plus
- Page 1 Fillcontrol Plus 19.10.2020 - Rev. C Operating manual Original operating manual...
-
Page 2: Table Of Contents
Switching and make-up variants ............. 6 12.3 Guarantee ....................14 Electrical connection .................. 7 6.5.1 Terminal diagram ..............7 6.5.2 RS-485 interface ................ 8 Installation and commissioning certificate ..........8 2 — English Fillcontrol Plus — 19.10.2020 - Rev. C... -
Page 3: Notes On The Operating Manual
Reflex Winkelmann GmbH accepts no liability for any damage resulting from vicinity can occur. failure to observe the information in this operating manual. In addition to the requirements set out in this operating manual, national statutory regulations ... -
Page 4: Description Of The Device
WC Make-up line to the device Make-up line to the system circuit "BV" shut-off valve Cover (hinged) Fillcontrol Plus controls the make-up with mains water for the system circuit. "PIS" pressure transducer Control Basic controller The controller monitors the following functions: "WV"... -
Page 5: Scope Of Delivery
This action is a – Bus modules: prerequisite for the making of warranty claims. • Profibus DP – Have the Reflex Customer Service carry out commissioning and • Ethernet the annual maintenance. Note! Installation conditions Separate operating instructions are supplied with accessories. -
Page 6: Wall Mounting
6.3.1 Wall mounting Switching and make-up variants Example of a pressure-dependent make-up with "Fillcontrol Plus". The device is installed at the wall. Bore holes for wall mounting are provided on the rear of the console (1) housing. Select the attachment means according to the wall properties and the weight (G) of the device. -
Page 7: Electrical Connection
Contact water meter (in "Fillset Impuls", for example), see chapter 4.6 "Optional equipment and accessories" on User, page 5 . optional • Evaluation of the make- • Contact 32/33 closed = meter pulse. Fillcontrol Plus — 19.10.2020 - Rev. C English — 7... -
Page 8: Rs-485 Interface
• Communication with other equipment. Minimum working pressure in bar Note! Initial pressure, diaphragm expansion vessel, in bar If required, please request the RS-485 interface protocol from the Reflex Static elevation in m Customer Service. • Connection details. ... -
Page 9: Use The Device To Fill The Facility System With Water
Press "Stop" on the controller. The Auto LED at the operator panel extinguishes. Functions: Except for the display of information, the device is non-functional in Stop mode. Function monitoring is stopped. • The "PU" pump is switched off. Fillcontrol Plus — 19.10.2020 - Rev. C English — 9... -
Page 10: Summer Operation
For a description of the operation, see chapter 9.1 "Operator panel" on • NO: The system does not offer more queries page 10 . regarding the softening process. All grey marked menu items must be reviewed during commissioning. 10 — English Fillcontrol Plus — 19.10.2020 - Rev. C... -
Page 11: Customer Menu
Service menu • 001 – 060: Maintenance recommendation in This menu is protected with a password. It can be accessed only by the Reflex months. Customer Service. A partial summary of the settings stored in the Service menu is proved in the Chapter Default settings. - Page 12 I/O module fault • I/O module defective. Inform Reflex Customer Service. • Connection between option card and controller faulty. • Option card defective. 12 — English Fillcontrol Plus — 19.10.2020 - Rev. C...
-
Page 13: Maintenance
"Quit" to acknowledge the "Maintenance recommended" message. Reset the maintenance counter in the Customer menu. Note! Arrange for maintenance tasks must be carried out only by specialist personnel or Reflex Customer Service. Fillcontrol Plus — 19.10.2020 - Rev. C English — 13... -
Page 14: Disassembly
Conformity and standards with the device physically isolated from the power supply. • Before you remove the covers, completely isolate the device controller Device conformity declarations are available on the Reflex homepage. from the power supply. www.reflex-winkelmann.com/konformitaetserklaerungen • Verify that the main circuit board is voltage-free. - Page 15 Installation and commissioning certificate - This device has been installed and commissioned in accordance with the instructions provided in the operating manual. The settings in the controller match the local conditions. Typ / Type: Fabr. Nr. / Serial-No. Fillcontrol Plus — 19.10.2020 - Rev. C English — 15...
- Page 16 Reflex Winkelmann GmbH Gersteinstraße 19 59227 Ahlen, Germany +49 (0)2382 7069-0 +49 (0)2382 7069-9546 www.reflex-winkelmann.com...
Need help?
Do you have a question about the Fillcontrol Plus and is the answer not in the manual?
Questions and answers