1. Manuals
  2. Brands
  3. AUTEC Manuals
  4. Remote Control
  5. Air series
  6. User manual

AUTEC Light Series User Manual

Transmitter system
Hide thumbs Also See for Light Series:
Table of Contents

Advertisement

Quick Links

Transmitter System
USER'S MANUAL
Light Series

Advertisement

Table of Contents
loading

Related Manuals for AUTEC Light Series

Summary of Contents for AUTEC Light Series

  • Page 1 Transmitter System USER’S MANUAL Light Series...
  • Page 3 Transmitter System USER’S MANUAL Light Series...
  • Page 4 (attached to the manual). If this manual is lost or damaged, ask for a copy from AUTEC. Please specify the serial number of the relative radio remote control.
  • Page 5 3.1 Technical data of the LK transmitting unit..............6 Warnings for use....................7 Warnings for maintenance..................8 5.1 Routine maintenance ....................8 5.2 Special maintenance (AUTEC SERVICE) ............... 9 5.3 Disposal ........................9 Working mode of the LK transmitting unit ............10 Frequencies......................12 7.1 Manual selection mode ..................

  • Page 6: Permitted Uses

    Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Autec cannot be held responsible if the radio remote control is installed on applica- tions that are different from those permitted:...
  • Page 7 The machine producer and/or the person who decides upon radio remote control use and installation is responsible for this analysis. Autec cannot be held responsible if the risk analysis is not carried out correctly. To guarantee correct radio remote control operation, all current regulations regarding safety at work and accident prevention should be respected.

  • Page 8: General Technical Data

    The radio remote control identification and approval data is given on plates that are on both the transmitting unit and the receiving unit. These plates MUST NOT be: - removed from their position - altered or damaged (contact Autec for replacement) 2.2 GENERAL TECHNICAL DATA Frequency band..................902 - 928 MHz Available radio channels.................... 32 Hamming distance ....................
  • Page 9 3 LK TRANSMITTING UNIT These transmitting units can be used with one of the following receiving units: - Type R102 - Type R202 - Type R302 - Type R402. starting keyswitch STOP pushbutton START pushbutton technical data plate signalling LED battery pushbuttons identification plate (in the battery housing)

  • Page 10: Air Pressure

    The number of pushbuttons in the LK transmitting unit varies depending on its configura- tion. The receiving units of the Light series are equipped with a safety function called SAFETY that protects the system “machine+radio remote control”, when it is in neu- tral (rest) position, from unintended movements caused by possible radio remote control faults.

  • Page 11: Warnings For Use

    4 WARNINGS FOR USE The user MUST ALWAYS respect the following warnings: VISUALLY FOLLOW all movements of the machine and its load remaining in- side the typical working range of the radio remote control. BE POSITIONED in a way that permits him to see the system “machine+radio remote control”, and above all the load, in the best possible way.

  • Page 12: Warnings For Maintenance

    5 WARNINGS FOR MAINTENANCE ENSURE THAT THE BATTERY HAS BEEN REMOVED FROM THE TRANSMIT- TING UNIT BEFORE CARRYING OUT ANY MAINTENANCE WORK. All control and maintenance actions carried out on the radio remote control must be verified and recorded by the person in charge of carrying out maintenance on the machine. Before carrying out maintenance and/or diagnostics it is recommended to re- place the battery with a charged one and ensure the efficiency of the starting keyswitch.
  • Page 13 5.2 SPECIAL MAINTENANCE (AUTEC SERVICE) Any fault should be repaired by authorised personnel (contact AUTEC SER- VICE), using original Autec spare parts only. Authorized Service Center...

  • Page 14: Power On And Start Up

    6 WORKING MODE OF THE LK TRANSMITTING UNIT POWER ON AND START UP 1. To switch on the transmitting unit, insert the starting keyswitch in the appropriate COMMAND ACTIVATION slot. Activate the pushbuttons and/or 2. To start the radio remote control func- selectors related to any of the tions, press the START pushbutton for 1-2 movement or selection com-...

  • Page 15: Switching Off

    STOP The STOP pushbutton should be pressed when it is necessary to stop the ma- chine immediately when a dangerous condition should occur. To stop the machine immediately, press the STOP pushbutton. To start working again, after checking that the working conditions are safe, turn the STOP pushbutton in the direction indicated to deactivate it and repeat the start- ing procedure.

  • Page 16: Manual Selection Mode

    7 FREQUENCIES Radio frequency transmission of AUTEC radio remote controls operates inside fre- quency bands permitted by European regulations that are valid when the radio re- mote control is placed on the market. Each radio remote control is programmed by the producer in the AUTOMATIC scan mode (producer's standard programming) or MANUAL selection mode.
  • Page 17 8 PROGRAMMING The dip switches must be programmed when the battery is removed from the transmitting unit. Programming must only be carried out by authorised per- sonnel. The incorrect closure of the transmitting unit can compromise the seal be- tween the casings and thereby the protection degree from dust and water. For the correct functioning, the group of 8 dip switches (excluding DIP 1) for the radio modules E16STXUS1 (transmitting unit) and E16SRXUS1 (receiving unit) must be set in the same way.
  • Page 18 9 LK TRANSMITTING UNIT DIAGNOSTICS If the system “machine+radio remote control” does not start, check if the problem is caused by the radio remote control or the machine. Therefore, before carrying out any verification connect the cable control unit: if the machine does not start, the problem lies with the ma- chine itself.
  • Page 19 Appendix: FREQUENCY TABLE E16STXUS1 DIP SWITCH DIP SWITCH 902.150 OFF OFF OFF 915.350 OFF OFF OFF 903.050 916.250 OFF OFF OFF OFF 903.850 917.050 OFF OFF OFF OFF 904.650 917.850 OFF OFF OFF OFF OFF 905.525 OFF OFF 918.675 OFF OFF 919.525 906.325 907.175...
  • Page 20 Tel : ++39 - 0444/901000 r.a. Tel : ++39 - 0444/901000 r.a. Via Pomaroli, 65 Via Pomaroli, 65 email: info@autec.it email: info@autec.it 36030 Caldogno (VI) ITALY 36030 Caldogno (VI) ITALY Fax: ++39 - 0444/901011 Fax: ++39 - 0444/901011 http://www.autec.it http://www.autec.it...

Table of Contents