Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cabletron Systems MMAC-Plus 9F106-01
Summary of Contents for Cabletron Systems MMAC-Plus 9F106-01
- Page 1 ™ MMAC-Plus 9F106-01 Two Port FDDI Router User’s Guide...
- Page 2 Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
-
Page 3: Fcc Notice
Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. -
Page 4: Doc Notice
Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté... -
Page 5: Table Of Contents
Chapter 1 Introduction Features... 1-1 Related Manuals... 1-4 Getting Help ... 1-4 Chapter 2 Installing the MMAC-Plus Module The Reset Switch ... 2-3 Local Management Console ... 2-3 Installing an FPIM... 2-6 Chapter 3 Operation Flexible Network Bus (FNB)... 3-2 System Management Buses ... -
Page 6: Chapter 1 Introduction
Introduction The 9F106-01 module, shown in Figure 1-1, is a two port FDDI router. One front panel network connection can be made to this module and routed to any other MMAC-Plus module via the FNB bus. Features Processor The 9F106-01 is equipped with an advanced IDT R4600 Fourth Generation 64 bit RISC microprocessor. - Page 7 With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Hot Swapping The 9F106-01 can be installed or removed from the chassis while the MMAC-Plus is powered up without affecting the operation of the remaining modules in the chassis.
- Page 8 FDDI 9F106-01 MMAC PLUS Figure 1-1. The 9F106-01 Module Features...
-
Page 9: Related Manuals
Cisco Systems R4500 manuals - CRM-DOC or CRM-CDROM Getting Help If you need additional support with the MMAC-Plus, or if you have any questions, comments or suggestions concerning this manual, feel free to contact Cabletron Systems Technical Support: By phone: By CompuServe By Internet mail:... -
Page 10: Chapter 2 Installing The Mmac-Plus Module
Remove the module from the plastic bag. Observe all precautions to prevent damage from Electrostatic Discharge (ESD). Carefully examine the module, checking for damage. If any damage exists, DO NOT install the module. Contact Cabletron Systems Technical Support immediately. Before installing the MMAC-Plus cards into the chassis, ensure that the bottom and top plastic tabs are unlocked. - Page 11 Installing the MMAC-Plus Module Metal Back-Panel FLNK FLNK FLNK FLNK FLNK Circuit Card Card Guides Warning: Ensure that the circuit card is between the card guides. Lock down the top and bottom plastic tabs at the same time, applying even pressure. Figure 2-1.
-
Page 12: The Reset Switch
Local Management Console Local Management is accessed by attaching a management console at the RJ-45 CON port of the 9F106-01. The console connection supports a Digital Equipment Corporation VT 320™ terminal or PC emulation of one of these terminals. Table 2-1 lists the setup requirements for the local management console. If your terminal is a Digital Equipment Corporation VT 320™... - Page 13 Installing the MMAC-Plus Module Table 2-1. Terminal Setup Requirements Menu Display Setup: General Setup: Communications Setup: Keyboard Setup: Function Selection Columns 80 Columns Controls Interpret Controls Auto Wrap No Auto Wrap Text Cursor Cursor Mode 7 Bit Control Cursor Keys Normal Cursor Keys Transmit...
- Page 14 Figure 2-3. Console Cable Pinouts Connect the console to the module as follows: Attach the male RJ-45 connector to the CON port of the 9F106-01. Attach the female end (25-pin or 9-pin, as applicable) to the terminal. Refer to the Cisco Systems documentation for information on configuring this module.
-
Page 15: Installing An Fpim
Installing the MMAC-Plus Module Installing an FPIM The 9F106-01 module is shipped without FPIMs. To install an FPIM, follow the procedure below: Remove the module if it is installed in the MMAC-Plus chassis. Remove the blank front cover over the FPIM slot. -
Page 16: Chapter 3 Operation
Operation The 9F106-01 FDDI module is a two port router for the MMAC-Plus. One front panel network connection can be made to this module and routed to any other MMAC-Plus module via the FNB bus. Interface DC/DC System Converter Diagnostic... -
Page 17: Flexible Network Bus (Fnb)
LCD located on the Environmental Module. The 9F106-01 have been designed so that in the event of a diagnostic controller fault, the modules will continue to function. -
Page 18: Fnb Interface
FNB-1 or FNB-2; the second allows dual attachment to both FNB-1 and FNB-2. The 9F106-01 has one dual attachment to the FNB backplane, connecting to either FNB-1 or FNB-2. The module can insert into the FNB or bypass it. -
Page 19: Chapter 4 Lanview Leds
LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figure 4-1, indicate the status of the module and may be used as an aid in troubleshooting. FDDI 9F106-01 FDDI Transmit FDDI Receive Figure 4-1. LANVIEW LEDs Chapter 4 System Status... - Page 20 LANVIEW LEDs The functions of the System Management Bus (SMB) and CPU LEDs are listed in Table 4-1. LED Color Green Yellow (Flashing) Yellow Red (Flashing) * Front Panel FDDI down. The function of the FNB Receive LED is listed in Table 4-2. LED Color Yellow (Flashing) The function of the FNB Transmit LED is listed in Table 4-3.
- Page 21 The function of the FDDI Receive LED is listed in Table 4-4. Table 4-4. FDDI Receive LED LED Color Yellow (Flashing) Activity (Flashing rate indicates rate of activity). No activity The Function of the FDDI Transmit LED is listed in Table 4-5. Table 4-5.
-
Page 22: Chapter 5 Specifications
Specifications Safety It is the responsibility of the person who sells the system to which the module will be a part to ensure that the total system meets allowed limits of conducted and radiated emissions. CAUTION This equipment meets the following safety requirements: •... -
Page 23: Physical
Specifications Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) Weight Unit: Shipping: Environment Operating Temperature Storage Temperature Relative Humidity 1.36 kg. (3 lb) 1.81 kg. (4 lb) 5 to 40 C -30 to 90 C 5% to 95% non-condensing... -
Page 24: Appendix A Fpim Specifications
FPIM Specifications This MMAC-Plus module uses Fiber Port Interface Modules (FPIM) to provide front panel cable connections. The FPIMs are user-installable. See the section titled Installing an FPIM on page 2-6. FPIM-00 The FPIM-00 has a MIC style connector supporting a multimode fiber connection. The specifications are listed in Table A-1. -
Page 25: Fpim-02 And Fpim-04
FPIM Specifications Transmitter power parameters are listed in Table A-2. Parameter 50/125 m fiber 62.5/125 m fiber 100/140 m fiber Error Rate The link distance is up to 2 kilometers on the multimode fiber-optic cable as specified by ANSI MMF-PMD. FPIM-02 and FPIM-04 The FPIM-02 has an RJ-45 connector supporting an Unshielded Twisted Pair (UTP) connection. - Page 26 FPIM-05 The FPIM-05 has a MIC style connector supporting a Single-mode fiber connection. The specifications are listed in Table A-4. Transmitter Peak Wave Length Spectral Width Rise Time Fall Time Duty Cycle Bit Error Rate The link distance is up to 40 kilometers (max) and 25 kilometers (typical) on single mode fiber-optic cable as specified by ANSI SMF-PMD.
Need help?
Do you have a question about the MMAC-Plus 9F106-01 and is the answer not in the manual?
Questions and answers