1. Manuals
  2. Brands
  3. Cabletron Systems Manuals
  4. Network Router
  5. MMAC-Plus 9T106-01
  6. User manual

Cabletron Systems MMAC-Plus 9T106-01 User Manual

Two port fddi router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
™
MMAC-Plus
9T106-01
Two Port FDDI Router
User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MMAC-Plus 9T106-01 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cabletron Systems MMAC-Plus 9T106-01

Summary of Contents for Cabletron Systems MMAC-Plus 9T106-01

  • Page 1 ™ MMAC-Plus 9T106-01 Two Port FDDI Router User’s Guide...
  • Page 3 Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

  • Page 4: Fcc Notice

    Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

  • Page 5: Doc Notice

    Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté...
  • Page 6 Notice...

  • Page 7: Table Of Contents

    Chapter 1 Introduction Features... 1-1 Related Manuals... 1-4 Getting Help ... 1-4 Chapter 2 Installing the MMAC-Plus Module The Reset Switch ... 2-3 Local Management Console ... 2-3 Chapter 3 Operation Flexible Network Bus (FNB)... 3-2 System Management Buses ... 3-2 System Diagnostic Controller...
  • Page 8 Contents...

  • Page 9: Chapter 1 Introduction

    Introduction The 9F106-01 FDDI Router module, shown in Figure 1-1, is a two port FDDI router. Onefront panel network connections can be made to this module and routed to any other MMAC-Plus module via the FNB bus. Features Processor The 9F106-01 is equipped with an advanced IDT R4600 Fourth Generation 64 bit RISC microprocessor.
  • Page 10 For a complete list of supported MIBs, refer to the release notes provided in the NOTE module package. LANVIEW LEDs The 9F106-01 uses LANVIEW: the Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Hot Swapping...
  • Page 11 FDDI 9F106-01 MMAC PLUS Figure 1-1. The 9F106-01 Module Features...

  • Page 12: Related Manuals

    Cisco Systems R4500 manuals - CRM-DOC or CRM-CDROM Getting Help If you need additional support with the MMAC-Plus, or if you have any questions, comments or suggestions concerning this manual, feel free to contact Cabletron Systems Technical Support: By phone: By CompuServe By Internet mail:...

  • Page 13: Chapter 2 Installing The Mmac-Plus Module

    Remove the module from the plastic bag. Observe all precautions to prevent damage from Electrostatic Discharge (ESD). Carefully examine the module, checking for damage. If any damage exists, DO NOT install the module. Contact Cabletron Systems Technical Support immediately. Before installing the MMAC-Plus cards into the chassis, ensure that the bottom and top plastic tabs are unlocked.
  • Page 14 Installing the MMAC-Plus Module Metal Back-Panel FLNK FLNK FLNK FLNK FLNK Circuit Card Card Guides Warning: Ensure that the circuit card is between the card guides. Lock down the top and bottom plastic tabs at the same time, applying even pressure. Figure 2-1.

  • Page 15: The Reset Switch

    The Reset Switch The Reset switch is located on the front panel, under the top plastic tab, as shown in Figure 2-2. It serves two functions: • Pressing the Reset switch twice within three seconds causes the processor to reset. •...
  • Page 16 Installing the MMAC-Plus Module Table 2-1. Terminal Setup Requirements Menu Display Setup: General Setup: Communications Setup: Keyboard Setup: Function Selection Columns 80 Columns Controls Interpret Controls Auto Wrap No Auto Wrap Text Cursor Cursor Mode 7 Bit Control Cursor Keys Normal Cursor Keys Transmit...
  • Page 17 An RJ-45 connector provides a CON interface to the management terminal. Figure 2-3 shows the pinouts. RECEIVE TRANSMIT SIGNAL GROUND DATA SET READY DATA TERMINAL READY COM PORT RJ-45 TRANSMIT RECEIVE SIGNAL GROUND DATA SET READY DATA TERMINAL READY Figure 2-3. Console Cable Pinouts Connect the console to the module as follows: Attach the male RJ-45 connector to the CON port of the 9F106-01.
  • Page 18 Installing the MMAC-Plus Module...

  • Page 19: Chapter 3 Operation

    Chapter 3 Operation The 9F106-01 FDDI Router module is a two port router. One front panel network connection can be made to this module and is routed to any other port and to any other MMAC-Plus module via the FNB bus. SMB-1 DC/DC System...

  • Page 20: Flexible Network Bus (Fnb)

    Operation Flexible Network Bus (FNB) The FNB consists of two dual FDDI networks, the FNB-1 and FNB-2, providing up to 400 Mbps of data bandwidth. These FDDI networks are 100% ANSI FDDI- compliant, supporting SMT (version 7.3), MAC, PHY, and PMD standards. This allows the FNB to traverse multiple MMAC-Plus hubs, or connect to any ANSI FDDI-compliant device, through standard A/B port connections.

  • Page 21: Fnb Interface

    FNB Interface MMAC-Plus modules are designed with one of two attachment policies. One allows dual attachment of a module to either FNB-1 or FNB-2; the second allows dual attachment to both FNB-1 and FNB-2. The 9F106-01 has one dual attachment to the FNB backplane, connecting to either FNB-1 or FNB-2.
  • Page 22 Operation...

  • Page 23: Chapter 4 Lanview Leds

    LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figure 4-1, indicate the status of the module and may be used as an aid in troubleshooting. F D D I 9 F 1 0 6 - 0 2 S M B FDDI Receive FDDI Transmit Figure 4-1.
  • Page 24 LANVIEW LEDs The functions of the System Management Bus (SMB) and CPU LEDs are listed in Table 4-1. LED Color Green Yellow (Flashing) Yellow Red (Flashing) * Front Panel FDDI down. The function of the FNB Receive LED is listed in Table 4-3. LED Color Yellow (Flashing) The function of the FNB Transmit LED is listed in Table 4-3.
  • Page 25 The function of the FDDI Receive LED is listed in Table 4-4 Table 4-4. FDDI Receive LED LED Color Yellow (Flashing) Activity (Flashing rate indicates rate of activity). No activity The Function of the FDDI Transmit LED is listed in Table 4-5 Table 4-5.
  • Page 26 LANVIEW LEDs...

  • Page 27: Chapter 5 Specifications

    Specifications Safety It is the responsibility of the person who sells the system to which the module will be a part to ensure that the total system meets allowed limits of conducted and radiated emissions. CAUTION This equipment meets the following safety requirements: •...

  • Page 28: Physical

    Specifications Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) Weight Unit: Shipping: Environment Operating Temperature Storage Temperature Relative Humidity 1.36 kg. (3 lb) 1.81 kg. (4 lb) 5 to 40 C -30 to 90 C 5% to 95% non-condensing...

Table of Contents

Save PDF