Advertisement

Quick Links

www.ti.com
User's Guide
LMR38020EVM User Guide
The LMR38020EVM is a 80 V DC/DC buck regulator that employs synchronous rectification to achieve high
conversion efficiency in a small footprint. The EVM operates over a wide input voltage range of 6 V to 80 V
to provide a regulated 5 V output at 400 kHz switching frequency. The output voltage has better than 1.5%
setpoint accuracy and is adjustable using an external resistor divider. The module design uses the LMR38020F
synchronous buck converter with wide input voltage (wide V
side and low-side power MOSFETs, cycle-by-cycle overcurrent protection, and precision enable. The LMR38020
converter is available in an 8-pin SO PowerPAD
solutions. The LMR38020EVM evaluation module is qualified for the LMR38020 as well as the LMR38020-Q1
buck converter. See
Table 1-1
CONVERTER
U1
1 General TI High Voltage Evaluation User Safety Guidelines..............................................................................................
2 LMR38020 Evaluation Module...............................................................................................................................................
Procedure........................................................................................................................................................4
2.2 Detailed Descriptions.........................................................................................................................................................
3
Schematic................................................................................................................................................................................7
Layout..............................................................................................................................................................................8
Materials......................................................................................................................................................................11
Figure 3-1. LMR38020EVM Schematic.......................................................................................................................................
Figure 4-1. Top Layer and Silkscreen Layer................................................................................................................................
Figure 4-2. Mid-Layer 1 Ground Plane........................................................................................................................................
Figure 4-3. Mid-Layer 2 Routing..................................................................................................................................................
Routing..............................................................................................................................................10
Trademarks
PowerPAD
is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
SNVU787 - JULY 2021
Submit Document Feedback
ABSTRACT
package to enable high density, low component count DC/DC
for package information.

Table 1-1. Device and Package Configurations

IC
LMR38020-Q1
8-pin SO package with PowerPAD (4.89 mm × 3.90 mm)
LMR38020

Table of Contents

List of Figures
View..........................................................................................................................................4
List of Tables
Configurations...........................................................................................................................1
Materials................................................................................................................................11
Copyright © 2021 Texas Instruments Incorporated
) range, wide duty-cycle range, integrated high-
IN
PACKAGE
Table of Contents
2
4
5
7
8
9
9
LMR38020EVM User Guide
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LMR38020EVM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texas Instruments LMR38020EVM

  • Page 1: Table Of Contents

    LMR38020EVM User Guide ABSTRACT The LMR38020EVM is a 80 V DC/DC buck regulator that employs synchronous rectification to achieve high conversion efficiency in a small footprint. The EVM operates over a wide input voltage range of 6 V to 80 V to provide a regulated 5 V output at 400 kHz switching frequency.
  • Page 2: General Ti High Voltage Evaluation User Safety Guidelines

    WARNING: While the EVM is energized, never touch the EVM or its electrical circuits as they could be at high voltages capable of causing electrical shock hazard. LMR38020EVM User Guide SNVU787 – JULY 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 3 High Voltage! Electric shock is possible when connecting board to live wire. Board should be handled with care by a professional. For safety, use of isolated test equipment with overvoltage and overcurrent protection is highly recommended. SNVU787 – JULY 2021 LMR38020EVM User Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 4: Lmr38020 Evaluation Module

    LMR38020 Evaluation Module www.ti.com 2 LMR38020 Evaluation Module The LMR38020EVM is configured to deliver 5 V and 2 A at a switching frequency of 400 kHz. • Tightly-regulated output voltage of 5 V with 1.5% setpoint accuracy • Wide input voltage operating range of 4.5 V to 80 V •...
  • Page 5: Detailed Descriptions

    The LMR38020 PGOOD is an open-drain output that is tied to voltage below 20 V through pull-up resistor R SNVU787 – JULY 2021 LMR38020EVM User Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 6 J6 PIN-2 is connected to output for output voltage sensing and efficiency measurement. PIN-1 is connected to the noise injection resistor R3. The loop response can be measured on J6. LMR38020EVM User Guide SNVU787 – JULY 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 7: Schematic

    Schematic 3 Schematic Figure 3-1. LMR38020EVM Schematic SNVU787 – JULY 2021 LMR38020EVM User Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 8: Pcb Layout

    Figure 4-4 show the board layout for the LMR38020EVM. The EVM offers resistors, capacitors, and test points to configure the output voltage, precision enable, and switching frequency. The 8-pin SO PowerPAD™ package offers an exposed thermal pad, which must be soldered to the copper landing on the PCB for optimal thermal performance.
  • Page 9: Figure 4-2. Mid-Layer 1 Ground Plane

    PCB Layout Figure 4-2. Mid-Layer 1 Ground Plane Figure 4-3. Mid-Layer 2 Routing SNVU787 – JULY 2021 LMR38020EVM User Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 10: Figure 4-4. Bottom Layer Routing

    PCB Layout www.ti.com Figure 4-4. Bottom Layer Routing LMR38020EVM User Guide SNVU787 – JULY 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 11: Bill Of Materials

    Bill of Materials 5 Bill of Materials Table 5-1. LMR38020EVM Bill of Materials Ref Des Description Part Number Vendor Printed Circuit Board BSR166 CAP, CERM, 0.1 µF, 100 V, ±10%, X7R, AEC-Q200 Grade HMK107B7104KAHT Taiyo Yuden 1, 0603 C3, C12 CAP, CERM, 0.1 µF, 50 V, ±10%, X7R, AEC-Q200 Grade 1,...
  • Page 12 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
  • Page 13 www.ti.com Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product.
  • Page 14 www.ti.com Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à...
  • Page 15 www.ti.com EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices.
  • Page 16 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2019, Texas Instruments Incorporated...
  • Page 17 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2021, Texas Instruments Incorporated...

Table of Contents