Advertisement

Quick Links

www.ti.com
User's Guide
LMR38025QEVM User's Guide
The
LMR38025QEVM
is an 80-V DC/DC buck regulator that employs synchronous rectification to achieve
high conversion efficiency in a small footprint. The EVM operates over a wide input voltage range of 6 V
to 80 V to provide a regulated 5-V output at 400-kHz switching frequency. The output voltage has better
than 1.5% setpoint accuracy and is adjustable using an external resistor divider. The module design uses the
LMR38025SQDRRRQ1
synchronous buck converter with the following:
Wide input voltage (wide V
Wide duty-cycle range
Integrated high-side and low-side power MOSFETs
Cycle-by-cycle overcurrent protection
Spread spectrum
The LMR38025-Q1 converter is available in an 12-pin WSON integrated circuit package to enable high-density,
low-component count DC/DC designs. The LMR38025QEVM evaluation module is qualified for the LMR38025-
Q1 as well as the LMR38025 buck converter. See
CONVERTER
U1
1 General TI High Voltage Evaluation User Safety Guidelines..............................................................................................
2 LMR38025-Q1 Evaluation Module.........................................................................................................................................
Procedure........................................................................................................................................................5
2.2 Detailed Descriptions.........................................................................................................................................................
Photo...............................................................................................................................................................................8
4
Schematic................................................................................................................................................................................9
Layout............................................................................................................................................................................10
6 Bill of Materials.....................................................................................................................................................................
Curves.............................................................................................................................................................14
Figure 4-1. LMR38025Q Schematic............................................................................................................................................
Figure 5-1. Top Layer and Silkscreen Layer..............................................................................................................................
Figure 5-3. Mid-Layer 2 Routing................................................................................................................................................
Routing..............................................................................................................................................12
Figure 7-2. Load Regulation......................................................................................................................................................
= 48 V, V
IN
SNVU848 - NOVEMBER 2023
Submit Document Feedback
ABSTRACT
) range
IN
Table 1-1
Table 1-1. Device and Package Configurations
IC
LMR38025-Q1
LMR38025

Table of Contents

List of Figures
Setup...........................................................................................................................................5
Photo...........................................................................................................................................8
Plane.......................................................................................................................................11
Current.......................................................................................................................................14
= 5 V, I
= 2.5 A........................................................................................................
OUT
= 48 V, V
IN
= 48 V, V
= 250 mA to 2.25 A at 200 mA/µs.....................................................
IN
OUT
= 48 V, V
IN
Copyright © 2023 Texas Instruments Incorporated
for package information.
PACKAGE
12-pin WSON package (3.00 mm × 3.00 mm)
= 2.5
A.......................................................................................14
= 5 V, I
= 2.5 A..............................................................
OUT
OUT
= 2.5 A................................................................................
Table of Contents
13
10
11
14
14
14
14
15
LMR38025QEVM User's Guide
3
5
6
9
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LMR38025QEVM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texas Instruments LMR38025QEVM

  • Page 1: Table Of Contents

    Spread spectrum The LMR38025-Q1 converter is available in an 12-pin WSON integrated circuit package to enable high-density, low-component count DC/DC designs. The LMR38025QEVM evaluation module is qualified for the LMR38025- Q1 as well as the LMR38025 buck converter. See Table 1-1 for package information.
  • Page 2 = 5 V, I = 2.5 A..........15 List of Tables Table 1-1. Device and Package Configurations...........................1 Table 6-1. LMR38025QEVM Bill of Materials..........................Trademarks All trademarks are the property of their respective owners. LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback...
  • Page 3: General Ti High Voltage Evaluation User Safety Guidelines

    WARNING: While the EVM is energized, never touch the EVM or its electrical circuits as they could be at high voltages capable of causing electrical shock hazard. SNVU848 – NOVEMBER 2023 LMR38025QEVM User's Guide Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 4 High Voltage! Electric shock is possible when connecting board to live wire. Board should be handled with care by a professional. For safety, use of isolated test equipment with overvoltage and overcurrent protection is highly recommended. LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 5: Lmr38025-Q1 Evaluation Module

    LMR38025-Q1 Evaluation Module 2 LMR38025-Q1 Evaluation Module The LMR38025QEVM is configured to deliver 5 V and 2.5 A at a switching frequency of 400 kHz. • Tightly regulated output voltage of 5 V with 1.5% setpoint accuracy • Wide input voltage operating range of 4.2 V to 80 V •...
  • Page 6: Detailed Descriptions

    , of 115 KΩ. Refer to the External UVLO section of the LMR38025-Q1 SIMPLE SWITCHER® 4.2-V to 80-V, 2.5-A Synchronous Buck Converter With 40-μA IQ data sheet more detailed application information. PWRGD (J1) Power-good indication LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 7 J6 PIN-1(VO_S) is connected to the output for output voltage sensing and efficiency measurement. PIN-2(Vinj) is connected to the noise injection resistor R3. The loop response can be measured on J6. SNVU848 – NOVEMBER 2023 LMR38025QEVM User's Guide Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 8: Evm Photo

    EVM Photo www.ti.com 3 EVM Photo Figure 3-1. LMR38025Q EVM Photo LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 9: Schematic

    Schematic 4 Schematic Figure 4-1. LMR38025Q Schematic SNVU848 – NOVEMBER 2023 LMR38025QEVM User's Guide Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 10: Pcb Layout

    Figure 5-4 show the board layout for the LMR38025QEVM. The EVM offers resistors, capacitors, and test points to configure the output voltage, precision enable, and switching frequency. The 12-pin WSON integrated circuit package offers an exposed thermal pad, which must be soldered to the copper landing on the PCB for optimal thermal performance.
  • Page 11: Figure 5-2. Mid-Layer 1 Ground Plane

    PCB Layout Figure 5-2. Mid-Layer 1 Ground Plane Figure 5-3. Mid-Layer 2 Routing SNVU848 – NOVEMBER 2023 LMR38025QEVM User's Guide Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 12: Figure 5-4. Bottom Layer Routing

    PCB Layout www.ti.com Figure 5-4. Bottom Layer Routing LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 13: Bill Of Materials

    Bill of Materials 6 Bill of Materials Table 6-1. LMR38025QEVM Bill of Materials REF DES DESCRIPTION PART NUMBER VENDOR Printed Circuit Board BSR279 CAP, CERM, 0.1 µF, 100 V,+/- 10%, X7R, AEC-Q200 C1,C2,C19,C2 HMK107B7104KAHT Taiyo Yuden Grade 1, 0603 CAP, CERM, 0.1 µF, 50 V,+/- 10%, X7R, AEC-Q200 Grade...
  • Page 14: Performance Curves

    = 10 V to 70 V at 200 = 250 mA to 2.25 A at 200 mA/µs V/ms, V = 5 V, I = 2.5 A LMR38025QEVM User's Guide SNVU848 – NOVEMBER 2023 Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 15: Figure 7-7. Control Loop Response

    = 2.5 A Figure 7-9. CISPR 25 Class 5 Conducted Emissions Plot: V = 48 V, V = 5 V, I = 2.5 A SNVU848 – NOVEMBER 2023 LMR38025QEVM User's Guide Submit Document Feedback Copyright © 2023 Texas Instruments Incorporated...
  • Page 16 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
  • Page 17 www.ti.com Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product.
  • Page 18 www.ti.com Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à...
  • Page 19 www.ti.com EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices.
  • Page 20 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2023, Texas Instruments Incorporated...
  • Page 21 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2023, Texas Instruments Incorporated...

Table of Contents