AUMA TIGRON TR-M30X Short Instructions
  1. Manuals
  2. Brands
  3. AUMA Manuals
  4. Controller
  5. TIGRON TR-M30X
  6. Short instructions

AUMA TIGRON TR-M30X Short Instructions

Multi-turn actuators profibus dp
Hide thumbs Also See for TIGRON TR-M30X:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

Multi-turn actuators
TIGRON
TR-M30X
Profibus DP
Use short instructions in combination with operation instructions only!
These short instructions are only complete with the respective operation instructions of the
actuator. Safety and warning instructions contained in the actuator operation instructions must
be heeded when performing work on the actuator!
Short instructions
TR-M1000X
Fieldbus connection

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TIGRON TR-M30X and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AUMA TIGRON TR-M30X

Summary of Contents for AUMA TIGRON TR-M30X

  • Page 1 Multi-turn actuators TIGRON TR-M30X TR-M1000X Profibus DP Use short instructions in combination with operation instructions only! These short instructions are only complete with the respective operation instructions of the actuator. Safety and warning instructions contained in the actuator operation instructions must be heeded when performing work on the actuator! Short instructions Fieldbus connection...
  • Page 2 Table of contents Table of contents Page Basic information on fieldbus connection................Fieldbus connection for line topology................. Set fieldbus (slave address) via device menu..............Profibus parameter overview in device menu..............
  • Page 3 The electrical connection of the actuator must be opened to be able to connect the Electrical connection fieldbus cables. Refer to Operation instructions “Multi-turn actuators TIGRON TR-M30X TR-M1000X” (Y009.100), “Electrical connection” chapter. The Electrical connection” chapter of the operation instructions fully applies to the connection of the fieldbus cables.
  • Page 4 Fieldbus connection for line topology Fieldbus connection for line topology Figure 1: Line topology □ Channel 1: Further fieldbus devices follow ▣ Channel 2 (redundancy only): further fieldbus devices follow Last fieldbus device ■ Fieldbus cable from previous device (input) Fieldbus cable to next device (output) Connection at terminal carrier For flexible cables, the fieldbus connection can be made via spring clamp terminals...
  • Page 5 Fieldbus connection for line topology Connection with support terminals When using solid cables (single or multiple strands), additional support terminals must be used.The support terminals (terminal blocks) are mounted above the terminal carrier. Figure 4: Terminal assignment of support terminals: Channel 1 (1A/1B) [XK] Terminal assignment according to wiring diagram (customer connection): □...
  • Page 6 Set fieldbus (slave address) via device menu Set fieldbus (slave address) via device menu Information Local actuator settings are made using the Combi-Switch. Operate the yellow shuttle dial of the Combi-Switch to scroll within the menu Operate the black selector switch (outer ring), either to confirm the selected menu or to go one step back (ESC).
  • Page 7 Profibus parameter overview in device menu Profibus parameter overview in device menu Device menu parameters can also be set via the AUMA CDT software. For information on AUMA CDT, refer to the operation instructions and our website at www.auma.com. For further information on these parameters and all other settings, refer to the Manual (Operation and setting).
  • Page 8 AUMA Riester GmbH & Co. KG P.O. Box 1362 DE 79373 Muellheim Tel +49 7631 809 - 0 Fax +49 7631 809 - 1250 info@auma.com www.auma.com Y009.309/003/en/1.21 For detailed information on AUMA products, refer to the Internet: www.auma.com...

This manual is also suitable for:

Tigron tr-m60xTigron tr-m120xTigron tr-m250xTigron tr-m500xTigron tr-m1000x

Table of Contents