Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tractel Dynarope HF36/3/LPT
Summary of Contents for Tractel Dynarope HF36/3/LPT
- Page 1 Tension meter dynarope HF36/3/LPT Operation and maintenance manual...
-
Page 2: Table Of Contents
SUMMARY DEFINITIONS ......................3 PICTOGRAMS USED IN THIS MANUAL ..............3 STANDARD CONTENT OF DELIVERY ..............3 INTRODUCTION ......................4 4.1. Description ........................4 4.2. Characteristics ........................ 4 4.3. Data bank HF 36/3/LPT ....................4 4.4. Specific Calibration ......................5 PRESENTATION ...................... - Page 3 9. Tractel® declines any responsibility for use of this unit in a setup configuration not described in this manual.
-
Page 4: Definitions
1. DEFINITIONS In this manual, the following terms mean: « Product » : Equipment element or assembly defined on the cover page, delivered complete in its standard version, or as one of the various models described. « Installation » : Comprehensive set of operations required to place a complete product in a condition ready for commissioning (or connection to other components for commissioning), starting from the state in which the product has been delivered. -
Page 5: Introduction
INTRODUCTION 4.1. Description This tension meter dynarope HF 36/3 LPT is an electronic load cell that has been designed to measure the effort applied in a wire rope without having to dismantle the installation. The resulting signal generated by the sensor equipped with strain gauges is interpreted by a digital display controlled by a microprocessor. -
Page 6: Specific Calibration
Nominal Nominal Nominal Position of Ref. Item Material Structure diameter diameter diameter the stop Range (daN) Calibration (mm) (/'') (mil'') block 5026 Steel 6 x 36 0,7874 500 - 7000 5027 Steel 6 x 36 13/16 0,8268 500 - 8000 5052 Steel 6 x 36... -
Page 7: Presentation
5. PRESENTATION 5.1. Tension meter HF 36/3/LPT Crank Sheaves Bronze nut Support of the sheave Tightening Screw Strain gages Crank support LEMO Plug Rotary stop block Axle of the sheave LEMO cable LEMO connector is a « push-pull » connector. The LEMO self-latching system allows the connector to be mated or unmated by simply pushing or pulling axially on the outer release sleeve. -
Page 8: Display Hf 87/T/Lpt
5.2. Display HF 87/T/LPT Display Batteries cover fixing screws Key board Batteries AA1,5V (3) USB Plug (option) Gasket LEMO plug * Batteries cover LEMO connector is a « push-pull » connector. The LEMO self-latching system allows the connector to be mated or unmated by simply pushing or pulling axially on the outer release sleeve. -
Page 9: Display Information And Keyboard Functions
5.3. Display information and keyboard functions A Battery level indication B Current temperature C GPS Status D Current unit E Position of the rotary stop block F Current measure T Key • Press 3 sec = increase police of Graphic visualization of the measure between the current measure •... -
Page 10: To Carry A Measurement Out
• Connect the tension meter to the display using the provided LEMO cable. • Turn the display "ON", the screen will display : ® o Tractel logo o Parameters setting values • Select the type of tension meter presently connected to your display. (e.g: 36 /3 ) -
Page 11: To Install The Tension Meter On The Wire Rope
• Install the tension meter on the wire rope (ref to § 6.1). • Screen will display (ref to § 5.3) : o Current measurement units o Current temperature o Battery level of charge o Measured effort Note: MIN = effort below the measurement range of the selected cable MAX = effort above the measurement range of the selected cable 6.1. -
Page 12: Configuration Menu
7. CONFIGURATION MENU • Accede to the Menu by pressing the • Use the key board to scroll the menu (See § 5.3 ) ON/OFF PARAMETRES LANGUAGE AUTO OFF BACKLIGHT TIME DATE INFORMATION RESTORE RECORDS READ DELETE UNITS LOAD DIAMETER TEMPERATURE •... -
Page 13: Advanced Functions
• RECORDS READ Read the previous logged operations DELETE To clear the memory • UNITS LOAD UNITS N, daN, kN, kg, lbf, lbs "g" COEFFICIENT Modify the default parameter : 9,81 DIAMETER Available units : mm, decimal inches, fraction inches. TEMPARATURE Available units : C°... -
Page 14: Record
Note: the effort must be an actual value (neither "–MIN–" nor "–MAX–" ) otherwise, the display shows the error message “!” 8.2. Record To record the data at the end of a measurement process • Press key " " during the measurement process, display will show "REC" •... -
Page 15: Use
8.4.2 Use • Press F2 and select the cable -- Special -- (first line of the list) • Select an existing custom calibration o Select “Use” with key to use the custom calibration • Turn the stop block on the displayed position and confirm the setting with (see §... -
Page 16: Maintenance, Checking And Cleaning
International Standard calibrator. ® Tractel recommends an annual metrological check for every appliance. 9.3. Maintenance The sensor/display unit requires no specific maintenance other than a regular cleaning with a dry cloth. -
Page 17: Error Messages
10.2. Error messages Message Cause Solution Use the optional « LOADER » software to update Corrupted Error in the wire rope parameters. the data bank. signature Or, consult the manufacturer. Use the optional « LOADER » software to update Corrupted Error in the wire rope parameters. -
Page 18: Product Markings
PRODUCT MARKINGS HF 36/3/LPT n° : XXXXXX Ø : 20 > 44 mm (0,7874 to 1,7323 in) : 40000 daN (89600 lbs) : IP 65 Made in Belgium HF 87/T/LPT n° : XXXXXX : IP 65 : AA (1.5 VDC) x 3 Made in Belgium Serial number Identification (TYPE)
Need help?
Do you have a question about the Dynarope HF36/3/LPT and is the answer not in the manual?
Questions and answers