Episode EA-WAKE-2D Owner's Manual
  1. Manuals
  2. Brands
  3. Episode Manuals
  4. Amplifier
  5. EA-WAKE-2D
  6. Owner's manual

Episode EA-WAKE-2D Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EA-WAKE-2D
Wake Amp
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Episode EA-WAKE-2D

Summary of Contents for Episode EA-WAKE-2D

  • Page 1 EA-WAKE-2D Wake Amp Owner’s Manual...
  • Page 2 Introduction Thank you for purchasing Episode® Electronics. To complete installation, follow these guidelines. Visit our website for design recommendations and speaker calculators. Contents • 1x WAKE Amp • 2x Junction box screws • 1x Face plate • 2x Faceplate screws •...

  • Page 3: Getting Connected

    Getting Connected 1. Strip back 1/4” of insulation from each wire that is to be connected to the amplifier. Twist the exposed conductors tightly so there are no stray strands. 2. Connect the wires going to each speaker making sure to maintain proper polarity. Warning: Do not connect the power supply to AC power while wiring the WAKE Amp.

  • Page 4: Mobile App Setup

    Mobile App Setup Download the WAKE Amp mobile app from the Apple App Store or Google Play store. Open the app and it automatically searches for available WAKE Amps. Tap the WAKE Amp you want to configure and the Amp Setup page appears. Tap the icons along the bottom of the page, to navigate through configuration options.
  • Page 5 Keypad Volume Settings • Keypad Controls Volume. Selecting this feature causes the WAKE Amp’s buttons to control the amp volume. • Keypad Controls Music. Selecting this feature causes the WAKE Amp’s volume to be controlled by the source and the WAKE Amp’s buttons control track forward, back and pause. •...
  • Page 6 Bluetooth Reconnect Toggle on to have the WAKE Amp try to automatically reconnect to the paired Bluetooth device, if disconnected. If toggled off, the WAKE Amp automatically enters Bluetooth Pairing mode after disconnecting from a paired device. EQ Tab The EQ tab includes Treble and Bass adjustments. Loudness boost is a dynamic EQ boost to both bass and treble when the amp is at lower volumes.

  • Page 7: Button Behavior

    Firmware Tab The firmware tab checks for new firmware versions. Tap the Update button to push firmware updates via Bluetooth. Note: The firmware update process uses Bluetooth to transfer the firmware file from the mobile device to the WAKE Amp. This process can take up to 20 min. To reduce file transfer time ensure that the mobile device is in close proximity to the WAKE Amp.

  • Page 8: Factory Reset Procedure

    Function LED Behavior Firmware Update LED 1 blinks during update process. Mute/Pause LED 1 illuminates red. No Source Connected LED 1 slowly blinks blue. Factory Reset LEDs 1-5 blink red. Bluetooth Pairing Mode LEDs 1-5 blink blue. Error LEDs 1-5 illuminate red. LEDs 1-5 illuminate blue to show the current Current Volume volume level.

  • Page 9: Specifications

    5. All LEDs slowly blink pink. The unit is validating the stored factory default firmware file. 6. All LEDs quickly blink pink. The unit is reprogramming the processor memory. 7. LED 1 blinks pink. The unit is reprogramming the Bluetooth module. 8.
  • Page 10 Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC.

This manual is also suitable for:

Wake amp ea-wake-2d

Table of Contents