Episode EA-AMP-HYB-2D-1000 Product Manual
Hide thumbs
Also See for EA-AMP-HYB-2D-1000:
- Quick start manual (4 pages) ,
- Quick start manual (9 pages) ,
- Product manual (20 pages)
Table of Contents
Advertisement
LINE IN
CH2
CH1
NETWORK
SERIAL
TRIGGER
CONTROL
CONTROL
DC 12 V
IN
OUT
LINK
ACT
PROTECT
CLIP
-10
-20
SIGNAL
CH1
CH1
CH1
LINE OUT
CH2
CH2
CH2
PRODUCT MANUAL
EA-AMP-HYB-2D-1000
EA-AMP-HYB-2D-2000
PROTECT
CLIP
CH.SEL
-10
-20
MENU
SIGNAL
ADJUST | SET
CH2
BACK
SPEAKER OUT
DIGITAL
BRIDGE
CH1
IN
CH2
CH1
OUT
EA-AMP-HYB-2D-1000
ON
U
L
C
UL
LIFTED
Use only a 250V fuse
Employer uniquement aux
OFF
un fusible de 250V
Advertisement
Table of Contents
Related Manuals for Episode EA-AMP-HYB-2D-1000
Summary of Contents for Episode EA-AMP-HYB-2D-1000
- Page 1 PRODUCT MANUAL EA-AMP-HYB-2D-1000 EA-AMP-HYB-2D-2000 PROTECT PROTECT CLIP CLIP CH.SEL MENU SIGNAL SIGNAL ADJUST | SET EA-AMP-HYB-2D-1000 BACK SPEAKER OUT DIGITAL LINE IN LINE OUT BRIDGE NETWORK SERIAL TRIGGER CONTROL CONTROL DC 12 V LIFTED Use only a 250V fuse Employer uniquement aux...
- Page 2 page | 2 www.snapav.com Support 866.838.5052 www.snapav.com Support 866.838.5052...
-
Page 3: Table Of Contents
Audio Sense ................................10 Volume Calibration ..............................10 Calibration Setup Tips ............................10 Troubleshooting ................................10 Distorted Audio At Normal Volume ........................10 Inline Volume “Thump” ............................11 Specifications ................................11 Warranty ..................................15 Contacting Technical Support ..........................15 © 2019 Episode®... -
Page 4: Important Safety Instructions
page | 4 CAUTION Risk of Electrical Shock! DO NOT OPEN! ATTENTION ! RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR ! The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - Page 5 LA PRISE PRINCIPALE DU CORDON D’ALIMENTATION doit rester facilement accessible . POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, NE PAS RETIRER. NO réparable par 18. ATTENTION: l’utilisateur pièces à l’intérieur. CONFIER L’ENTRETIEN DE PERSONNEL QUALIFIÉ . © 2019 Episode®...
-
Page 6: Introduction
| 6 INTRODUCTION Thank you for purchasing Episode® Amplifiers. This amplifier is a 2 channel (70V or 8ohm selectable on each) designed for applications requiring two channel stereo audio, or two mono zones of audio with different sources or levels. Channels can also be bridged to increase output power and send a singular mono signal. -
Page 7: Rear Panel
Speaker Terminals Note proper positive and negative connections for operating in bridge mode when desired J. Power Switch Main amplifier power switch K. IEC Power Cord Detachable power for amplifier L. AC Fuse Replaceable main power fuse © 2019 Episode®... -
Page 8: Source Connections
page | 8 SOURCE CONNECTIONS Balanced and unbalanced connections are available as shown below. Line out connections may be used to send audio signals to other equipment. DIGITAL LINE IN LINE OUT Input mode, source, pre-out, and gain adjustments can all be made via the GUI home screen. www.snapav.com Support 866.838.5052 www.snapav.com Support 866.838.5052... -
Page 9: Speaker Connections And Output Mode
Use 14 or 16 gauge stranded two-conductor speaker wire. Connect the SPEAKER OUT BRIDGE appropriate conductor to each screw terminal, observing correct polarity. Bridged markings are also shown to the left. Use burial rated wire as necessary for outdoor applications. © 2019 Episode®... -
Page 10: Amplifier Power Control
page | 10 AMPLIFIER POWER CONTROL Front Panel Power Button When the amplifier is powered ON, the power swoosh will illuminate solid blue. When it is in STAND-BY, the power button will be red. Resetting the Amplifier Press and hold the power button for 10 seconds once the receiver is powered on for a “soft” reset. This will reset login information. -
Page 11: Inline Volume "Thump
12 Volt Trigger 3.5 mm Mono Jack Dimensions (Inches) 17”W x 1.73”H x 14”D Rack Spacing Input Voltage 115V AC/230V AC Weight 12 lbs Certification Meets FCC Part 15, UL EN60065 AC Power Consumption 230W Typical 1100W Max © 2019 Episode®... - Page 12 page | 12 SPEAKER PRESETS Amplifiers come with a preloaded bank of presets noted in the table below. This includes full system presets and DSP settings for any landscape speaker when used in combination with ES-LS-BSUB-12 or ES-LS-HSUB-10. CHANNEL 2 LS-SAT-4 LS-SAT-6 LS-SAT-8...
- Page 13 LS-BSUB-12 (8Ω) LS-BSUB-10 (8Ω) PRESET GROUP B Preset# Preset Name Channel Voltage Speaker Hookup Default 8Ω Flat 8Ω Flat LS MIX4_6 SAT 4 SAT 6 LS MIX4_8 SAT 4 SAT 8 LS MIX6_8 SAT 6 SAT 8 © 2019 Episode®...
- Page 14 page | 14 To use any landscape speaker and ES-LS-BSUB-8 or ES-LS-BSUB-10, please see the configuration table below. Each parameter can be accessed and implemented via the local UI. Parameters for each reference configuration can be found in the support tab. CHANNEL 2 LS-SAT-4 LS-SAT-6...
-
Page 15: Warranty
WARRANTY 2-Year Limited Warranty Episode® Amplifiers have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to a designated service center with an assigned return authorization (RA) number. - Page 16 © 2019 Episode® Rev: 190403-1120...