Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Episode EA-AMP-SUB-1D-500R
Summary of Contents for Episode EA-AMP-SUB-1D-500R
- Page 1 INSTALLATION MANUAL EA-AMP-SUB-1D-500R EA-AMP-SUB-1D-500R...
- Page 2 page | 2 CAUTION Risk of Electrical Shock! DO NOT OPEN! ATTENTION ! RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR ! The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
- Page 3 NOTE: Total impedance (SUB 1 + SUB 2) should not be less than 4Ω. K. VOLTAGE SELECTOR Selects the appropriate input voltage setting: 100V or 220V. L. AC POWER IN IEC power cord. M. FUSE Additional fuse included for servicing. N. MASTER POWER SWITCH Switch between on/off. © 2015 Episode® © 2015 Episode®...
-
Page 4: Menu Display
page | 4 MENU DISPLAY V O L UME A U T O N I G H T MO V I E A. VOLUME DISPLAY B. VOLUME LEVEL Displays the volume level. NOTE: Lock mode overrides power mode. C. POWER MODE Displays the power control mode for the amplifier. - Page 5 E X I T directions until the knob is pressed to exit once returning to the “Menu Exit” screen. NOTE: The volume level can be adjusted immediately once exiting the sub menu to the main menu. © 2015 Episode® © 2015 Episode®...
-
Page 6: Installation
page | 6 SETUP Amplifier Positioning Placing the amplifier can have a large impact on performance and longevity. Please take the following guidelines into consideration: • Ensure that the unit is in a well-ventilated area that provides adequate cooling. • A minimum of 5” should be allowed above and below the amplifier for optimum performance. Minimum of 2"... - Page 7 Dual Sub Connections EA-AMP-SUB-1D-500R EA-AMP-SUB-1D-500R (LFE) DC 12V TRIGGER FUSE T8AL/250V 100-120V~60Hz/220-240V~50Hz 500WATTS OPERATE SUB 1 Total Impedance SUB 2 UPDATE 100-120V AC 220-240V AC (Sub 1 + Sub 2) Minimum 4 8Ω Minimum 8Ω Minimum © 2015 Episode® © 2015 Episode®...
- Page 8 page | 8 12V DC Trigger Connect the 12V trigger output of another device to the 12V trigger input of the amplifier using a high quality mono cable. AV Receiver +12V Trigger Switched Outlet (LFE) DC 12V TRIGGER OPERATE UPDATE GND (Sleeve) If the receiver does not have a 12V trigger output, using a 12V power supply plugged into a switched outlet on...
- Page 9 Power IR IN Power Cord IR Receiver Control System Connections HDMI 3.5mm Mono Mini AV Receiver (LFE) DC 12V TRIGGER OPERATE UPDATE EA-AMP-SUB-1D-500R RS 232 IR Ou tputs IR Inputs Control System Power Cord IR Receiver © 2015 Episode® © 2015 Episode®...
- Page 10 page | 10 FINE TUNE After making all connections and calibrating the speakers, fine tune the subwoofer as instructed below. See pages 4‒5 for more on menu functions. NOTE: When using an AV receiver and the LFE input, set the subwoofer calibration level to the factory setting, and select LFE for CROSSOVER.
-
Page 11: Specifications
TROUBLESHOOTING Episode amplifiers are designed to function trouble-free. Most problems that occur are due to simple issues. If having trouble, check the list of simple fixes below. If the problem persists, contact Episode technical support at 866.838.5052. • Audio cable to the source component is not connected properly, connection to output or the cable is defective. -
Page 12: Warranty
WARRANTY 2-Year Limited Warranty Episode® Amplifiers have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to a designated service center with an assigned return authorization (RA) number.