Related Manuals for Episode EA-AMP-SUB-1D-300
Summary of Contents for Episode EA-AMP-SUB-1D-300
- Page 1 INSTALLATION MANUAL EA-AMP-SUB-1D-300 EA-AMP-SUB-1D-300 EA-AMP-SUB-1D-300 T6.3AL 250V for 100-120V FUSE: T3.15AL 250V for 220-240V 100-120V~60Hz/220-240V~50Hz 300WATTS...
- Page 2 page | 2 www.snapav.com Support 866.838.5052 www.snapav.com Support 866.838.5052...
-
Page 3: Important Safety Instructions
22. WARNING: This product may expose you to chemicals known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov. 23. The use of the apparatus is in moderate climates. © 2019 Episode®... -
Page 4: Consignes De Sécurité Importantes
page | 4 CAUTION Risk of Electrical Shock! DO NOT OPEN! ATTENTION ! RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR ! Le flash de foudre avec le symbole de pointe de flèche, dans une triangle équilaterale, est prévu pour alerter l’utilisateur à la présence de la tens ion dangereuse non isolée dans la clôture du produit qui peut être de la grandeur suffisante pour constituer un risque de décharge électrique aux personnes.. - Page 5 Connects the speaker wires to the binding posts. NOTE: Total impedance (SUB 1 + SUB 2) should not be less than 4Ω. 12. VOLTAGE SELECTOR Selects the appropriate input voltage setting: 100V or 230V. 13. AC POWER IN IEC power cord. © 2019 Episode®...
-
Page 6: Master Power Switch
page | 6 FEATURES ( CONTINUED ) 14. FUSE Additional fuse included for servicing. 15. MASTER POWER SWITCH Switch between on/off. SETUP Amplifier Positioning Placing the amplifier can have a large impact on performance and longevity. Please take the following guidelines into consideration. - Page 7 EA-AMP-SUB-1D-300 T6.3AL 250V FOR 120V FUSE: T3.15AL 250V FOR 230V 100-120V~60Hz/220-240V~50Hz 300WATTS Single Sub Connections 4Ω Minimum EA-AMP-SUB-1D-300 EA-AMP-SUB-1D-300 T6.3AL 250V FOR 120V FUSE: T3.15AL 250V FOR 230V 100-120V~60Hz/220-240V~50Hz 300WATTS Dual Sub Connections 8Ω Minimum 8Ω Minimum © 2019 Episode®...
- Page 8 | 8 12V DC Trigger Connect the 12V trigger output of any other device with a 12V trigger cable to the input of the EA-AMP-SUB-1D-300 using a high-quality 3.5mm (1/8”) mono cable. AV Receiver +12V Trigger Switched Outlet or ...
- Page 9 4. Play a movie scene or music track and set the system volume to an average level. Listen to the bass level from the preferred listening position. Adjust the ‘VOLUME’ control as desired. 5. If deeper bass is desired, adjust the ‘CROSSOVER’ control toward the lower frequencies. Experiment with different frequency settings until finding one that sounds best. © 2019 Episode®...
-
Page 10: Specifications
TROUBLESHOOTING Episode amplifiers are designed to function trouble-free. Most problems that occur are due to simple issues. If having trouble, check the list of simple fixes below. If the problem persists, contact Episode technical support at 866-838-5052. • Power cable to the amplifier is incorrectly connected or plugged into an outlet that does not have power. -
Page 11: Warranty
SnapAV or a designated service center with prior notification and an assigned Return Authorization (RA) number. CONTACTING TECHNICAL SUPPORT As a thank you for purchasing Episode Electronics products, direct technical support services are available via phone ®... - Page 12 ® © 2019 Episode Rev: 190906-1445...