Advertisement
E3X-DA-N
Specifications
J AMPLIFIER RATINGS/CHARACTERISTICS
Description
Output type
NPN output
PNP output
Light source (wavelength)
Power supply voltage
Power
Normal
consumption
Economy mode
Digital display
not lit
Control output
ON/OFF output
Analog output
Operation
Switch
mode
selectable
Circuit protection
Response time
High-speed
by mode
Standard
Long distance
Sensitivity setting
Functions
Timer function
Automatic
power control
(APC)
Zero-reset
Initial reset
Monitor focus
Display
Function (color)
Timing
Orientation
Optical axis adjustment
Ambient illumination
Ambient
Operating
temperature
Storage
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
Digital output
Analog/digital output
Prewired
Connector
Prewired
E3X-DA11-N
E3X-DA6
E3X-DA21-N
E3X-DA41-N
E3X-DA8
E3X-DA51-N
Red LED (660 nm)
12 to 24 VDC ±10%, ripple (p-p) 10% max.
960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC)
720 mW max. (current consumption: 30 mA max. at power supply voltage of 24 VDC)
600 mW max. (current consumption: 25 mA max. at power supply voltage of 24 VDC)
NPN/PNP (depends on model) open collector; load cur-
rent: 50 mA max.; residual voltage: 1 V max.
---
Load 1 to 5 VDC,
10 kΩ min.
Light-ON/Dark-ON operation
Reverse polarity, output short-circuit, mutual interference prevention
250 µs for operation and reset respectively
1 ms for operation and reset respectively
4 ms for operation and reset respectively
Teaching or manual method
OFF-delay timer range: 0 to 20 ms (set in 1 ms increments); 20 to 200 ms (set in 5 ms increments)
Fiber-optic current digital control
Display can be reset to zero when required (negative values can be displayed).
Settings can be returned to defaults as required.
---
Upper and lower limits can
be set as required for every
100 digital values.
Operation indicator (orange), 7-segment digital incident level display (red), 7-segment digital inci-
dent level percentage display (red), threshold and excess gain 2-color indication bar (green and
red), 7-segment digital threshold display (red)
Normal/peak-hold/bottom-hold, program selectable
Normal/reverse, program selectable
Optical axis adjustment possible (flashing function)
Illumination intensity at light-intercepting surface:
l
Incandescent lamp: 10,000
x max.; Sunlight: 20,000
Groups of 1 to 3 Amplifiers: –25°C to 55°C (–13°F to 131°F)
Groups of 4 to11 Amplifiers: –25°C to 50°C (–13°F to 122°F)
Groups of 12 to16 Amplifiers: –25°C to 45°C (–13°F to 113°F)
with no icing or condensation
–30 °C to 70°C (–22°F to 158°F) with no icing or condensation
Operating and storage: 35% to 85% with no condensation
20 MΩ min. at 500 VDC
1,000 VAC at 50/60 Hz for 1 minute
10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions
(This table continues on the next page.)
Mark-detection
Connector
Prewired
E3X-DA7
E3X-DAB11-N
E3X-DA9
---
Blue LED
(470 nm)
NPN open col-
lector; load cur-
rent: 50 mA
max.; residual
voltage: 1 V
max.
---
---
---
l
x max.
E3X-DA-N
M8 connector,
digital output
E3X-DA14V
E3X-DA44V
Red LED (660 nm)
NPN/PNP
(depends on
model) open col-
lector; load current:
50 mA max.; resid-
ual voltage: 1 V
max.
---
Fiber-optic current
digital control
---
3
Advertisement
