Table of Contents
Advertisement
Ratings and specifications
Types
NPN output
Item
PNP output
connection method
Output
Power supply voltage
Power consumption
Sensor
Voltage range
input
Input impedance
range
Repeatability F.S./25°C
Display accuracy F.S.
Temperature characteristics F.S. ±1% F.S.
Control output
Response Time
Indicator
Protection circuit
Sensitivity adjustment
Maximum connectable Units
No. of Units for mutual
interference prevention
Operation mode
Zero Reset
Timer
Scaling
Resetting settings
*
5
Eco mode
Functions
Bank switching
Output 1 Settings
Output 2 Settings
Hysteresis width
Display switch
Key Lock
Current input
E9NC-AA10
E9NC-AA40
Connector for Sensor
Connector for Sensor
Communications Unit
Communications Unit
Pre-wired (2 m)
*
1 output
2
2 outputs
24 VDC (20.4 to 26.4 V) class2 power is supplied from the connector via the communication unit.
24 V power supply voltage in normal mode: 1,080 mW or less (consumption current 45 mA max.), eco-function ON: 840 mW or
less (consumption current 35 mA max.), and eco-function LO: 960 mW or less (consumption current 40 mA max.)
4 to 20 mA DC
204 kΩ±1% (Input: no-insulated)
±0.2% F.S.
±0.5% F.S. ±2digit
Load power supply voltage:
24 VDC (20.4 to 26.4 V)
class2,
open collector output type
Load current:
100 mA max. for 1 to 3 units
use, 20 mA max. for 4 or
Refer to the communication
more units connected
unit specifications
Residual voltage:
Load current less than 10
mA: 1 V max.,
Load current 10 to 100 mA:
2 V max.
Off-state current: 0.1 mA
max.
1/10/100/500ms/1/10/30/60s (Initial value 500 ms)
Seven Segment Display (both sub and main digital display: white)
OUT indictor (orange), NO/NC indicator (orange), ST indicator (blue), zero-reset indicator (green)
OUT selective indicator (orange) (two lamps only)
Power supply reverse connec-
tion protection,
Power supply reverse connec-
output short-circuit protection,
tion protection,
and output reverse connection
output short-circuit protection
protection
Smart Tuning (2-point tuning, full auto tuning, or percentage tuning (-99% to 99%)) or manual adjustment
Model E3NW-ECT
30 units when used
16 Units
Model E3NW-CCL, 16 units
when used
None
NO (Normal Open)/NC (Normal Close)
Yes
Select from timer disabled, OFF delay, ON delay, or One-shot timer
1 ms to 9999 ms
Set the upper/lower limits (-1999.9999 to 9999.9999, min. unit: 0.001)
Select from initial reset (factory defaults) or user reset (saved settings).
Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed).
Select from banks 1 to 4.
Select from Normal detection mode or Wind comparator (area) detection mode.
Select from Normal detection
mode, Wind comparator (ar-
---
ea) detection mode, and Error
output mode.
Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9999.9999.
Select from normal display, peak/bottom display, or CH number display (setting value display when adjusting the threshold)
Yes
Model for Sensor Communications Unit
E9NC-VA10
E9NC-AA0
E9NC-VA40
Connector for Sensor
Communications Unit
Pre-wired (2 m)
*
*
3
1 output
2
1 to 5 VDC
Load power supply voltage:
24 VDC (20.4 to 26.4 V)
class2,
open collector output type
Load current:
100 mA max. for 1 to 3 units
use, 20 mA max. for 4 or
more units connected
Residual voltage:
Load current less than 10
mA: 1 V max.,
Load current 10 to 100 mA:
2 V max.
Off-state current: 0.1 mA
max.
Power supply reverse connec-
tion protection,
output short-circuit protection,
and output reverse connection
protection
*
4,
16 Units
E9NC-AA/VA
Voltage input
*
1
E9NC-VA0
Connector for Sensor
Communications Unit
*
2 outputs
3
Refer to the communication
unit specifications
Power supply reverse connec-
tion protection,
output short-circuit protection
Model E3NW-ECT
30 units when used
Model E3NW-CCL, 16 units
when used
Select from Normal detection
mode , Wind comparator (ar-
---
ea) detection mode, and Error
output mode.
*
4,
3
Advertisement
Table of Contents
