Anomalies - Gaspardo MCE 6000 Use And Assembly Instructions / Spare Parts

7.0 ANOMALIES

,Q WKH HYHQW RI SUREOHPV ZLWK IXQFWLRQLQJ FDUU\ RXW WKHVH VLPSOH FRQWUROV WR FKHFN LI UHSDLUV DUH QHHGHG
,I WKH SUREOHP SHUVLVWV HYHQ DIWHU WKH VXJJHVWHG FKHFNV KDYH EHHQ SHUIRUPHG FRQVXOW WKH DUHD GHDOHU DQG WKHQ UHSRUW WKH PDOIXQFWLRQLQJ
WR WKH 0DQXIDFWXUHU XVLQJ WKH UHSRUW IRUP RQ WKH ODVW SDJH RI WKLV PDQXDO
ANOMALY
The Computer does not switch on.
To the ignition on the display "FAULt"
appears.
Monitor emits marks them acoustic in
continuation.
The sowing distance is wrong/not constant.
The speed sensor does not work.
A photocell does not work.
The switch does not exclude the rows.
7KH XVH RI FHOOXODU SKRQHV DQG &% UDGLRV DQG RSHUDWLQJ LQ PDJQHWLF ¿HOGV KLJKYROWDJH S\ORQV FDQ MHRSDUGL]H WKH IXQFWLR-
ning of the monitor.
cod. G19502283
USE AND MAINTENANCE
CAUSE
a) The power cable is disconnected.
7KH SRODULW\ RI WKH FRQQHFWLRQ LV QRW
corrected.
a) Short circuit within the wiring attach-
PHQWV RI WKH SKRWRFHOOV
a) The sowing tolerance (parameter "S")
is too low.
b) The photoelectric cells are dirty.
F $QRPDO\ RI VHHGV
d) Switches in ON (WITHOUT dispositive
H[FOXVLRQ URZV RI VHHG 
e) Switches in ON (WITH dispositive
H[FOXVLRQ URZV RI VHHG  ODFNHG H[FOX-
sion the row.
D :URQJ SRVLWLRQLQJ RI SKRWRHOHFWULF FHOOV
or the sensor speed.
b) Speed is not constant.
a) The cable is disconnected.
b) Adjusting distancetoo high.
F 7KH UHG SDUW RI WKH VHQVRU LV GDPDJHG
a) The cable is disconnected.
b) Transmitter and receiver are not cor-
rectly adjusted.
c) The photocell is damaged.
d) The signal cable connector is dirty.
H /XPLQRXV UHÀHFWLRQV LQWHUIHUH ZLWK WKH
SKRWRFHOOV¶ ¿HOG RI YLHZ
D FDEOH RI WKH LQWHUUXSWHG H[FOXVLRQ
E &RQQHFWLRQ RI IDVWRQ RI WKH ZURQJ
exclusion device or the invert the pola-
rity.
ATTENTION
-
REMEDY
a) Check the power cable
(See paragraph 5.3.3 page 21)
a) Check the electrical connections
(monitor/tractor) and ensure that the
FDEOHV DUH LQ SHUIHFW FRQGLWLRQ ,W LV
possible to detect the breakdown by
VZLWFKLQJ WKH LQVWUXPHQW RII DQG RQ
DJDLQ DIWHU KDYLQJ GLVFRQQHFWHG SKRWR-
FHOOV RQH DIWHU WKH RWKHU DQG WKH ZKROH
wiring.
D ,QFUHDVH JUDGXDOO\ WKH YDOXH RI VHQVLWLYLW\
programmed in parameter "S".
b) To clean up photoelectric cells with com-
pressed air or a material small brush (not
that can ruin to them, like iron or other).
F 7R YHULI\ VHHGHU
G ,Q SKDVH RI LW VHHGV WKH VZLWFKHV RI WKH
exclusion device rows must be in OFF.
H WR YHULI\ HYHQWXDO PHFKDQLFDO SUREOHP
on the exclusion device.
D &KHFN SRVLWLRQLQJ RI WKH SKRWRFHOOV
they must not obstacle the seed-drop
RU WKH PHFKDQLFDO IXQFWLRQLQJ RI WKH
sowing element.
b) Vedi sotto.
a) Connect the power cable.
b) Regulate the adjusting distance as indi-
cated in paragraph 5.3.2 on page 21.
c) Replace the sensor.
a) Connect the power cable.
b) Adjust transmitter and receiver cor-
rectly.
c) Replace the photocell.
d) Clean the connector pins with degre-
aser / electric deoxidizer).
e) Block out the sunlight by covering
points where it could penetrate.
a) To restore the connection.
b) to correct the connection in the polarity
case invert. To attend approximately 30
VHFRQG RQHV EHIRUH SXWWLQJ LQ IXQFWLRQ
the device.
ENGLISH
27