Buffalo TeraStation Pro WSS User Manual page 49

Errors and Information
The LCD panel on the TeraStation displays the messages below when errors occur.
LCD Message
ＳＹＳＴＥＭ Ｅｒｒｏｒ Ｅ１１
Ｆａｎ Ｆａｉｌｕｒｅ
ＳＹＳＴＥＭ Ｅｒｒｏｒ Ｅ１２
Ｃｏｏｌｉｎｇ Ｆａｉｌｕｒｅ
ＨＤｘ Ｅｒｒｏｒ Ｅ１６
ＨＤｘ Ｎｏｔ Ｆｏｕｎｄ
ＨＤｘ Ｂｒｏｋｅｎ Ｅ３０
Ｒｅｐｌａｃｅ ｔｈｅ Ｄｉｓｋ
ＳＹＳＴＥＭ Ｉ１０
ＴＯＯ ＨＯＴ！
ＯｐｅｒａｔｉｏｎＭｏｄｅＩ１２
Ｄｅｇｒａｄｅｄ Ｍｏｄｅ
ＲＡＩＤ Ｉ１８
ｘＤｒｉｖｅ Ｒｅｂｕｉｌｄｉｎｇ
Ｒｅｐｌｉｃａｔｉｏｎ Ｉ３３
ＲｅｐｌｉｃａｔｉｏｎＦａｉｌｕｒｅ
Ｎｅｗ Ｆｉｒｍｗａｒｅ Ｉ５２
Ａｖａｉｌａｂｌｅ
ＢａｃｋｕｐＴａｓｋｘ Ｉ５４
Ｂａｃｋｕｐ Ｆａｉｌｕｒｅ
TeraStation Pro WSS User Manual
Description
An error occurred in the fan speed.
Check that no foreign objects or dust are clogging the fan. If any foreign
objects or dust are found, use a pair of tweezers, air duster, or other tool
to remove them.
If the error is displayed again, contact Buffalo technical support for
assistance.
System temperature has exceeded the maximum safe value. Do not place
objects in the area around the TeraStation. Install the TeraStation in a cool
location.
Unable to find hard drive X. Hard drive X may be disconnected or may
have failed. Reinstall the hard drive.
The number X hard disk may have failed, or the number x hard disk may
be disconnected. Replace the hard disk.
The system temperature may have exceeded the safeguard value.
Do not place objects in the area around the TeraStation. Install the
TeraStation in a cool location.
Operating in degraded mode.
Rebuilding drive X in the array.
Note: Transfer speeds are slower during the rebuild process.
An error occurred during replication. Click Sync in Backup & Replication
Settings to attempt replication again.
A new firmware version has been released. Update the firmware.
A backup job has failed. Make sure that the backup job is cofigured
correctly, and that the NAS is on and not in standby mode. If the backup
job still fails, check the status of NAS, network, and backup source
destination. Also, check the backup log to see if any errors were recorded.
48