Related Manuals for Daktronics NPN-4100 Series
Summary of Contents for Daktronics NPN-4100 Series
- Page 1 NPN-4100 SERIES DAKT-0203-12 DISPLAY MANUAL P2035 DD3918319 Rev 01 16 May 2019 201 Daktronics Drive Brookings, SD 57006-5128 www.daktronics.com/support 800.325.8766...
- Page 2 Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
-
Page 3: Table Of Contents
Display ..............................3 Structure ..............................3 Glossary ..........................5 Replacement Parts .......................7 Replacement Parts List .........................7 Daktronics Exchange and Repair & Return Programs ..............7 Exchange Program ..........................7 Repair & Return Program .........................8 Shipping Address ..........................8 Warranty & Limitation of Liability......................9 A Reference Documents .......................11 Reference Drawings ......................13... - Page 4 This page intentionally left blank.
-
Page 5: Introduction
This manual explains the installation, maintenance, and troubleshooting of this video display system. For additional information regarding the safety, installation, operation, or service of this system, refer to the telephone numbers listed in Daktronics Exchange and Repair & Return Programs (p.7). This manual contains only generic installation topics and is not specific to a particular installation. -
Page 6: Module Numbers
Module Numbers Figure 3 explains the module labeling method in more detail, and Figure 4 illustrates how Daktronics numbers modules on a video display. Used to differentiate display face if system has more than one viewing face “A” denotes the first face, “B” the second, etc. -
Page 7: Warnings/Disclaimers
If any modifications of this nature are made, detailed drawings of the change(s) must be submitted to Daktronics engineering staff for evaluation and approval, or the warranty will be null and void. - Page 8 This page intentionally left blank.
-
Page 9: Glossary
LED tile via ribbon cable. Modules with the housing, LED tiles, and logic card can be removed from the front of the panel with a Daktronics-specific module removal tool. Pixel: the smallest single point of light on a display that can be turned on and off. For LED displays, a pixel is the smallest block of light emitting devices that can generate all available colors. - Page 10 This page intentionally left blank.
-
Page 11: Replacement Parts
& return program. Exchange Program Daktronics unique Exchange Program is a quick service for replacing key parts in need of repair. If a part requires repair or replacement, Daktronics sends the customer a replacement, and the customer sends the defective part to Daktronics. This decreases display downtime. -
Page 12: Repair & Return Program
Customer Service immediately. Daktronics expects immediate return of an exchange part if it does not solve the problem. Daktronics also reserves the right to refuse parts that have been damaged due to acts of nature or causes other than normal wear and tear. -
Page 13: Warranty & Limitation Of Liability
Warranty & Limitation of Liability The Daktronics Warranty & Limitation of Liability statement is located in Section C: Daktronics Warranty & Limitation of Liability (p.15). The warranty is independent of extended service agreements and is the authority in matters of service, repair, and display operation. - Page 14 This page intentionally left blank.
-
Page 15: A Reference Documents
Use the following documents in the order listed: • NPN-410X/ZPN-1000 Series Substructure Quick Guide (DD3922077) • NPN-4100 Series Panel Basics Quick Guide (DD3851280) • NPN-4100 Series Sectional Installation & Service Quick Guide (DD3830324) • NPN-410X Series Border Installation Quick Guide (DD3838321) Reference Documents... - Page 16 This page intentionally left blank.
-
Page 17: B Reference Drawings
Refer to the appropriate Installation & Service to highest point along the entire vertical length of the display tube(s). Quick Guide: NPN-4100 (DD3830324), NPN-4101 (DD4133945), NPN-4102 (DD4174150), or ZPN-1000 (DD4175845). DD3922077 201 Daktronics Drive Rev 03 Brookings, SD 57006-5128 16 April 2020 www.daktronics.com/support... - Page 19 NPN-4100 Series Panel Basics Quick Guide Page 1 of 1 Figure 1 (rotated front view) and Figure 2 (rotated rear view) show the basic features of a typical NPN-4100 series display panel. Detail A Detail A 1: Rotating draw latch @ 3 per panel 1: Top alignment pin (removable) @ 2 per panel 2: Module power harness (black &...
- Page 21 Refer to Figure 4. 1. Remove the panel from its packaging. Refer to the NPN-4100 Series Border Installation Quick Guide (DD3838321) 6. Ensure the panel is level and vertically plumb. Refer to Figure 5. Adjust before installing the first panel to determine when to install borders.
- Page 22 Figure 14: Set Panel in Place Figure 15: Engage Alignment Pin 3. Terminate the three-pin plug (Daktronics part number P-1351) onto the 3. Release the side alignment pins at connection and allow the pins to field SJOOW flexible cable. Installation instructions are located on the slide into the recesses of the other panel.
- Page 23 3. Connect the three-pin plug (P-1351) Figure 30. to the panel mount jack on the Z-filter 1. Use a Phillips screwdriver and the supplied hardware (Daktronics part Figure 30: MC Cable assembly and push the plug through number HC-1012 @ 3) to install the PLRs. Hand-tighten to 5 in-lbs. Refer c.
- Page 24 DWG-3903563 and the steps below for installation details. Refer to the contract-specific Signal 1. Use a Phillips screwdriver to remove the hardware (Daktronics part Note: Handle the module with care. Ensure all four magnet switches on Interconnect Drawing and Figure 39 for...
- Page 25 NPN-4100 Series Installation & Service Quick Guide Page 5 of 6 8. Connect the ProLink Router (PLR) cable to the accessory jack on the 4. Install jigs in the first column from the starting point upward to the top of 4.
- Page 26 NPN-4100 Series Installation & Service Quick Guide Page 6 of 6 10. Place mask jigging pieces (MP-4021293) in the corners of the tile 3. Remove the tile with the tile mask from the display. Refer to Remove Tile 3. Pull the cables gently and rock the AC connector back and forth to spanning between four tiles.
- Page 27 " T-25 hex bit (TH-1118) to remove the M5-0.8 x 10 mm machine Figure 2. b. Mount the panel mount M12 jack screw (Daktronics part number HC-3809581) above the panel mount (W-3884831) per DWG-3898915. 2. Select the correct border size location and set the screw aside for Step 2.
- Page 29 Refer to Numbering Conventions (p.1) for information regarding how to read the drawing number. These drawings offer general information pertaining to most NPN-4100 series displays and are listed in numeric order. Any contract-specific drawings take precedence over the general drawings.
- Page 30 This page intentionally left blank.
- Page 31 ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF 0S-3723175 WITH POWER ENTRANCEPLATE; DVN-I1 DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2017 DAKTRONICS, INC. (USA) HC-1004 NPN-4100 MACH SCR, #4-40 X 0.375, PHIL PAN HEAD, ZN PLTD...
- Page 32 THIRD ANGLE PROJECTION ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY PART # TORQUE ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. HC-1012 15 IN/LBS COPYRIGHT 2018 DAKTRONICS, INC. (USA) NPN A1 (4100)
- Page 33 ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY 0M-3802728 ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF BLANK ENTRANCE PLATE; NPN A1 DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) 0M-3842400 LANYARD ATTACHMENT BRKT; NPN A1...
- Page 34 THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING THIRD ANGLE PROJECTION ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) NPN-4100 PROJECT: FINAL ASSY HARN;...
- Page 35 THIRD ANGLE PROJECTION ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF INSTALL W-3881316 TO POWER JACK DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) IF PLR IS PRESENT NPN-4100...
- Page 36 THIRD ANGLE PROJECTION THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) NPN-4100 PROJECT: BLOCK DIAGRAM;...
- Page 37 THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING THIRD ANGLE PROJECTION ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2016 DAKTRONICS, INC. (USA) NPN A1 PROJECT:...
- Page 38 THIRD ANGLE PROJECTION THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) NPN-4100 PROJECT: INSTALL, DUAL PLR;...
-
Page 39: C Daktronics Warranty & Limitation Of Liability
Daktronics Warranty & Limitation of Liability This section includes the Daktronics Warranty & Limitation of Liability statement. Daktronics Warranty & Limitation of Liability... - Page 40 This page intentionally left blank.
- Page 41 Warranty Coverage. Daktronics warrants to the original end user (the “End User”, which may also be the Purchaser) that the Equipment will be free from Defects (as defined below) in materials and workmanship for a period of one (1) year (the “Warranty Period”). The Warranty Period shall commence on the earlier of: (i) four weeks from the date that the Equipment leaves Daktronics’...
- Page 42 In no event shall Daktronics be liable for loss, damage, or injury of any kind or nature arising out of or in connection with this Warranty in excess of the Purchase Price of the Equipment. The End User’s remedy in any dispute under this Warranty shall be ultimately limited to the Purchase Price of the Equipment to the extent the Purchase Price has been paid.
- Page 43 For End User’s protection, in addition to that afforded by the warranties set forth herein, End User may purchase extended warranty services to cover the Equipment. The Extended Service Agreement, available from Daktronics, provides for electronic parts repair and/or on-site labor for an extended period from the date of expiration of this warranty. Alternatively, an Extended Service Agreement may be purchased in conjunction with this Warranty for extended additional services.