Daktronics GALAXY GT6 Series Installation And Operation Manual
Hide thumbs
Also See for GALAXY GT6 Series:
- Installation and operation manual (42 pages) ,
- Installation quick manual (2 pages)
Related Manuals for Daktronics GALAXY GT6 Series
Summary of Contents for Daktronics GALAXY GT6 Series
- Page 1 GALAXY GT6 DISPLAY SERIES ® INSTALLATION AND OPERATION MANUAL P2056 DD3894917 Rev 03 20 March 2020 201 Daktronics Drive Brookings, SD 57006-5128 www.daktronics.com/support 800.325.8766...
- Page 2 Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
-
Page 3: Table Of Contents
Module Replacement ......22 Network and Communication Power Supply Replacement ....22 Installation �������������������������������������������9 Controller Replacement ......23 System Startup ...........9 12 Daktronics Exchange and Repair & Boot Sequence ���������������������������������������9 Return Programs ��������������������������������24 Start-Up Checklist �����������������������������������9 Exchange Program .........24 Communication Installation .....9 Before Contacting Daktronics �������������24 Network Connection ����������������������������10... - Page 4 This page intentionally left blank.
-
Page 5: Introduction
Unauthorized modifications are made to the display, display cabinet, or the control system Refer to Section B: Daktronics Warranty and Limitation of Liability (p�29) at the end of this manual for a link to the full Daktronics Warranty and Limitation of Liability. -
Page 6: Installation Preparation
All display modules are fully latched into the display cabinet Structure Requirements Support structure design depends on mounting method, installation height, display size, and weight. Because every installation site is unique, Daktronics approves no single procedure for mounting displays. Things to consider prior to installation: •... -
Page 7: Display Installation
Follow all guidelines and safety precautions in this manual when installing the display. Do not modify the display or control system in any manner without the written permission of Daktronics engineering staff. Any unauthorized modifications will nullify the warranty. Display Installation Preparation •... -
Page 8: Electrical Installation
A separate circuit also makes display maintenance and troubleshooting easier. Daktronics assumes no liability for any issues caused by line voltage fluctuations or other improper power conditions. •... -
Page 9: Power Requirements
Install this display according to all applicable local and national electrical codes. This includes proper grounding and bonding of the display. • Do not connect the display to any voltage other than that listed on the Daktronics product label. •... -
Page 10: Earth Ground Installation
All components of a display system—including but not limited to displays, control equipment, and connected peripheral equipment—must be electrically grounded. Only qualified individuals may perform electrical work, including verification of ground resistance. Daktronics is not responsible for improper grounding or damage incurred as a result of improper grounding. •... -
Page 11: Displays With Internal Power
2� Inside the J-box, connect the power wires to the wires coming from the display interior using wire nuts. Refer to Figure 4 for 120 120 V Termination VAC and Figure 5 for 120/240 VAC. The following colors are used for the pre- (Box with Cover Removed) terminated wires: 120 VAC... -
Page 12: Signal Cable Installation
Signal Cable Installation Primary/Mirror Display Interconnections For data to get from the Primary display to the Mirror display, the interconnect cable must be connected. This cable typically comes attached to the back of the display. 1� Locate cable, unpackage it, and remove protective caps from cables. -
Page 13: Network And Communication
It also provides basic information about available standard communication options. Daktronics is not responsible for setting up displays on a wide area network (WAN) but does assist with setting up communication on a local area network (LAN) or directly to a laptop. -
Page 14: Network Connection
Display IP address (provided by customer) • Ethernet patch cable to connect the computer to the display Work with Daktronics Technical Support when programming a static IP address on the player. Standard Communication Options For specific details on installing the communications, consult the quick guide and manual included with the communication equipment. -
Page 15: Venus Software Configuration
Log In - Hosted Server 1� Navigate to https://venus.daktronics.com. 2� Enter the user name and password provided by Daktronics into the Email and Password text boxes. Refer to Figure 9. 3� Change the password in the Update Password text boxes. -
Page 16: Venus Menu Overview
Venus Menu Overview After logging in to Venus, an initial screen shows the No dashboard information available message. Clicking the Menu button at the top-left corner of the screen opens the main Menu. Refer to Figure 11. Menu Item Description Shows status tiles for each display and any Dashboard active, online, associated devices such as VIP-... -
Page 17: Contact Info And Where To Get Help
8� Click Save. 9� Repeat Steps 3-8 for each display. Contact Info and Where to Get Help If further assistance is required, Daktronics Customer Service is available 24/7 via phone or online connection. Contact information and Venus account information is available at the top-right corner under the user name. -
Page 18: Display Maintenance
Display Maintenance This section explains the steps necessary to maintain Galaxy GT6 displays, which are ® front accessible only. Remove modules on the front of the display to gain access to internal components. Figure 15 and Figure 19 show internal component locations. •... -
Page 19: Ventilation System
5� Disconnect the SATA cables and unplug the power cable by squeezing the tabs on the sides of the plug head and pulling it out. Refer to Figure 17. 6� Reconnect the SATA and power cables to the module. 7� Push the cables into the display so they do not get pinched. -
Page 20: Dry Cleaning Process
Dry Cleaning Process 1� Turn off power to the display. 2� Rub a dry, soft terry cloth towel horizontally across each row of LEDs. Make four passes per row of LEDs before moving to the next row of LEDs. Work from top to bottom safely within reach from a lift or a stage. -
Page 21: Display Troubleshooting
Display Troubleshooting This section provides basic display information such as power and signal routing as well as basic troubleshooting tips for common problems. For issues not addressed in this manual, please contact Daktronics Technical Support. Module Removal Turn the " hex head wrench clockwise to remove modules from the display face�... -
Page 22: Signal Routing
Signal Routing Figure 20 shows how signal is routed through the display. Thermostat RJ45 Quick Input Connect Quick Connect Light Detector Fans Figure 20: Signal Routing 1� Signal enters the display from the external signal enclosure through the signal input quick-connect jacks (1). -
Page 23: Controller Diagnostics
Refer to Figure 23. Once the cables are connected, cycle power to the PLR and it will boot-up in self-test mode. Following is a table of a few possible messages. Contact Daktronics Technical Support for additional information or questions. Code... -
Page 24: Module Diagnostics
If any Err message is displayed, send the PLR back to Daktronics for repair or replacement. Module Diagnostics Modules are equipped with a status indicator LED that can help troubleshoot possible issues. Under normal operation, the status indicator LED should flash once every 4 seconds. -
Page 25: 10 Replacement Parts List
10 Replacement Parts List 0P-1127-0024 The following table contains some of the items that may 2465 need to be replaced over a period of time. All Galaxy ® GT6 displays ship with at least two spare modules with 02/19/12 Rev. 1 power supplies and two spare SATA cables depending on the size of the display. -
Page 26: 11 Replacing Parts
11 Replacing Parts Note: When removing modules from the display, do not allow them to hang by the cables. Module Removal Turn the " hex head wrench clockwise to remove modules from the display face� • Turn the " hex head wrench counter-clockwise to secure modules to the display •... -
Page 27: Controller Replacement
Controller Replacement The controller is located in the lower-left area of the display. Refer to Figure 27. From the bottom-left corner of the Primary face, go up to the second row of modules and over to the right two modules to locate the controller. -
Page 28: Daktronics Exchange And Repair
In most circumstances, the replacement part will be invoiced at the time it is shipped. If the failed part or replacement part is not returned to Daktronics within 3 weeks of the ship date, Daktronics will assume that the customer is purchasing the replacement part and will send an invoice for the value of the new sale part. -
Page 29: Repair & Return Program
Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1� Call or fax Daktronics Customer Service: • Phone: 866-343-3122 • Fax: 605-697-4444 2� Receive a Return Materials Authorization (RMA) number before shipping. - Page 30 This page intentionally left blank.
-
Page 31: A Reference Drawings
Reference Drawings Shop drawings show display dimensions, signal and power connection locations, as well as information on service access and power requirements. To obtain copies of shop drawings or other reference drawings specific to your display, contact Daktronics Customer Service: •... - Page 32 This page intentionally left blank.
-
Page 33: B Daktronics Warranty And Limitation
Daktronics Warranty and Limitation of Liability here Click to view Warranty and Limitation of Liability (SL-2374) information. Daktronics Warranty and Limitation of Liability...