Related Manuals for Daktronics VANGUARD VC6
Summary of Contents for Daktronics VANGUARD VC6
- Page 1 GENERIC SERVICE VANGUARD ® LARGE MATRIX SERIES DISPLAY MANUAL 17 October 2018 DD4007298 Rev 00 201 Daktronics Drive Brookings, SD 57006-5128 www.daktronics.com/support 800.325.8766...
- Page 2 Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
-
Page 3: Table Of Contents
Model Number Guide .......1 Module Replacement ......19 Installation Preparation ......2 Power Supply Replacement ....19 PLR Replacement ........20 Pre-Installation Checklist ......2 11 Daktronics Exchange and Repair & Structure Requirements ......2 Return Programs ........21 Required Tools ..........3 Daktronics Part Numbers ......21 Display Installation......4 Daktronics Exchange and Repair &... -
Page 5: Introduction
For a smooth installation, complete the steps in this manual in order. Contact Daktronics Technical Support with any questions before or during the installation process. Daktronics identifies manuals by the ED or DD number located on the cover page of each manual. For example, this manual is referred to as DD4007298. -
Page 6: Installation Preparation
Display structure and mounting must not obstruct air flow. • Light sensor must not be obstructed for the display to function properly. Daktronics is not responsible for the installations or the structural integrity of support structures done by others. Installation Preparation... -
Page 7: Required Tools
Required Tools The following table lists the minimum tools Daktronics recommends having on site for each installation. Daktronics only provides the specialized tools needed to complete the installation. Daktronics Provided Customer Provided Splice Wrench Hex Head Wrenches – " and "... -
Page 8: Display Installation
Follow all guidelines and safety precautions in this manual when installing the display. Do not modify the display or control system in any manner without the written permission of Daktronics’ engineering staff. Any unauthorized modifications will nullify the warranty. Display Installation Dos Inspect the display for damage prior to installation. -
Page 9: Display Installation
3. Attach a crane or lift truck to the lift eyes on the display’s top. Note: Lift eye spacing is set at Daktronics and should not be moved. Lift eyes should also remain in place after installation is complete. -
Page 10: Section Splicing
Section Splicing Display Section Numbering For displays with multiple sections, each section is numbered for easy installation. For a two-section display, the bottom section is 201 and the top section is 101. Refer to Figure 2. Section 101 Section 201 Figure 2: Two-Section Display Section Numbering For four-section displays, when looking from the front, the lower-left display section is 201... - Page 11 5. Starting at one end of the display, use the splice tool to draw the top section into the bottom until the splice key is fully engaged, as shown in Figure 5. 6. Ensure display sections are aligned and that LEDs are also in alignment. 7.
-
Page 12: Electrical Installation
Install this display according to all applicable local and national electrical codes. This includes proper grounding and bonding of the display. Do not connect the display to any voltage other than that listed on the Daktronics product label. Displays use single-phase power. Proper power installation is imperative for display operation. -
Page 13: Main Disconnect
Important Notes: • Daktronics recommends that a separate circuit be run to the electronic display(s) to isolate it and prevent any issues that could be caused by line voltage fluctuations or high frequency noise on the power line caused by other types of equipment. -
Page 14: Grounding
Only qualified individuals may perform electrical work, including verification of ground resistance. Daktronics is not responsible for improper grounding or damage Figure 8: Ground Lug incurred as a result of improper grounding. -
Page 15: Start-Up Procedure
Start-Up Procedure Start-Up Checklist Note: Before starting up the display, review this checklist to ensure that all parts are ready to operate correctly. • Confirm that power is correctly connected to the display. • Confirm there is sufficient power according to display requirements. •... -
Page 16: Network And Communication Installation
This section explains how to set up communications with a VC6 series display through a network or an individual computer. Daktronics is not responsible for setting up a customer’s network system as either a Local Area Network (LAN) or a Wide Area Network (WAN). -
Page 17: Display Maintenance
This section explains the steps necessary to maintain the Vanguard VC6 display. ® Daktronics Vanguard VC6 displays are front accessible only. Remove modules on the ® front of the display to gain access to internal components. Figure 9 shows internal component locations. -
Page 18: Ventilation System
Ventilation System Vanguard VC6 displays are equipped with a ventilation system that helps keep internal ® components at operable temperatures. Vanguard VC6 displays are rear ventilated, so ® the display support structure must allow adequate space or air movement for proper ventilation. -
Page 19: Display Troubleshooting
This section provides basic display information such as power and signal routing as well as basic troubleshooting tips for common problems. For issues not addressed in this manual, please contact Daktronics Technical Support. Power and Signal Routing Understanding power and signal flow through the display can help a technician troubleshoot an issue. -
Page 20: Signal Routing
Signal Routing Figure 12 shows how signal is routed through the display. Note: Signal routing may vary depending on display size. Power Supplies (PS) Thermostat Term PLR Power Panel Supply Power Quick Entrance Connect Light Output Sensor Fans Figure 12: Signal Routing 1. - Page 21 PLR and it will boot-up in self-test mode. Following is a table of a few possible messages. Contact Daktronics Technical Support for additional information or questions. If any Err message is displayed, send the PLR back to Daktronics for repair or replacement. Code...
-
Page 22: Module Diagnostics
Module Diagnostics Modules are equipped with a status indicator LED that can help troubleshoot possible issues. Under normal operation, the status indicator LED should flash once every 4 seconds. If a module is blank, but has power supplied to it, perform a module self-test to diagnose a module or signal cable failure. -
Page 23: 10 Replacing Parts
10 Replacing Parts Module Replacement Note: When removing modules from the display, do not allow them to hang by the cables. 1. Turn off power to the display. 2. Locate the latch fastener on the module. One is centered near the top of the module. -
Page 24: Plr Replacement
PLR Replacement The PLR is located behind the third module up from the bottom in the first column of modules, as shown in Figure 9 on page 14. If the display has two PLRs, they are located behind the third and fifth columns. PLRs can be found in both Primary and Mirror display faces as well as all sections of a sectional display. -
Page 25: Daktronics Exchange And Repair & Return Programs
Daktronics offers a unique Exchange Program as a quick service for replacing key parts in need of repair. If a part requires repair or replacement, Daktronics sends the customer a replacement, and the customer sends the defective part to Daktronics. This decreases display downtime. -
Page 26: Repair & Return Program
Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1. Call or fax Daktronics Customer Service:... -
Page 27: Shipping Address
Shipping Address Daktronics Customer Service 600 E 54th St N Case #____________ Sioux Falls, SD 57104 Email transportationhelp@daktronics.com Daktronics Exchange and Repair & Return Programs...