Table of Contents
Advertisement
Quick Links
S-Drive Field Loader
Portable Grain Belt Conveyor
Operator's Manual
This manual applies to:
Batco FX, Westfield WCX, Hutchinson HCX, GrainMaxx GCX
1500 Series: 1535, 1545
2000 Series: 2045
Gas, Electric, and Hydraulic Drives
Read this manual before using product. Failure to
follow instructions and safety precautions can
result in serious injury, death, or property
damage. Keep manual for future reference.
LOOKING FOR PARTS?
Check out our online
Parts Catalog!
Part Number: 8210–00009 R1
Revised: March 2021
Original Instructions
Advertisement
Chapters
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AGI Batco FX 1500 Series
Summary of Contents for AGI Batco FX 1500 Series
- Page 1 S-Drive Field Loader Portable Grain Belt Conveyor Operator’s Manual This manual applies to: Batco FX, Westfield WCX, Hutchinson HCX, GrainMaxx GCX 1500 Series: 1535, 1545 2000 Series: 2045 Gas, Electric, and Hydraulic Drives LOOKING FOR PARTS? Check out our online Parts Catalog! Read this manual before using product.
- Page 2 This product has been designed and manufactured to meet general engineering standards. Other local regulations may apply and must be followed by the operator. All personnel must be trained in the correct operational and safety procedures for this product. Use the sign-off sheet below to record initial and periodic reviews of this manual with all personnel.
-
Page 3: Table Of Contents
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR CONTENTS 1. Introduction ............................5 1.1 Serial Number Location......................5 1.2 Intended Use ..........................5 1.2.1 Misuse ........................6 2. Safety............................... 7 2.1 Safety Alert Symbol and Signal Words..................7 2.2 Follow Safety Instructions ......................7 2.3 Overhead Power Lines ...................... - Page 4 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 6.2 Start-up and Break-in ......................42 6.3 Operation - Electric Motor Models..................43 6.4 Operation - Gas Engine Models ....................43 6.5 Loading Area..........................43 6.6 Conveyor Belt Speed ....................... 44 6.7 Emergency Shutdown ......................44 6.8 Restarting with a Full Tube .....................
-
Page 5: Introduction
Keep this manual handy for frequent reference and to review with new personnel. A sign-off form is provided on the inside front cover for your convenience. If any information in this manual is not understood or if you need additional information, please contact AGI or your representative for assistance. -
Page 6: Misuse
1. INTRODUCTION S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR • Handling oilseed when specific operating and cleanout procedures are followed. Misuse Do not install/use the conveyor for/with: • transferring material other than dry, free-flowing food-grains. • lifting or using as a hoist or crane. 1.2.1 Misuse Do not install/use the conveyor for/with: •... -
Page 7: Safety
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY 2. Safety 2.1. Safety Alert Symbol and Signal Words This safety alert symbol indicates important safety messages in this manual. When you see this symbol, be alert to the possibility of injury or death, carefully read the message that follows, and inform others. -
Page 8: Moving Conveyor Belt Safety
2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2.4. Moving Conveyor Belt Safety • DO NOT step on or touch moving conveyor belt. • Shut off and lock out power to adjust, service, or clean. 2.5. Upending • Anchor intake end and/or support discharge end to prevent upending. -
Page 9: Guards Safety
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Figure 1. Conveyor Work Area (Gas/Electric Drive) 2.8. Guards Safety • Keep guards in place. Do not operate with guard removed. • Do not walk on, step on, or damage guards. •... -
Page 10: Raising And Lowering The Conveyor
2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2.9. Raising and Lowering the Conveyor • Before raising/lowering/moving/adjusting the conveyor, make sure the area around the conveyor is clear of obstructions and/or untrained personnel. Never allow anyone to stand on or beneath the conveyor when it is being placed. -
Page 11: Positioning The Conveyor
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY 2.12. Positioning the Conveyor • Transport and place equipment on reasonably level ground when raising, lowering, positioning, or operating. • Move the conveyor into position slowly. Do not unhitch and attempt to move by hand. •... -
Page 12: Gas Engine Safety
2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2.14.1 Gas Engine Safety Power Source • Keep guards in place and secure. • Properly ventilate surrounding area. • Never fill the fuel tank with the engine running, while smoking, or near an open flame. Always shut down and allow engine to cool before filling with fuel. -
Page 13: Hydraulic Power Safety
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY 2.14.3 Hydraulic Power Safety Power Source • Refer to the rules and regulations applicable to the power source operating your hydraulic drive. • Do not connect or disconnect hydraulic lines while system is under pressure. -
Page 14: Tire Safety
2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2.15. Tire Safety Failure to follow proper procedures when mounting a tire on a wheel or rim can produce an explosion that may result in serious injury or death. • DO NOT attempt to mount a tire unless you have the proper equipment and experience to do the job. -
Page 15: Personal Protective Equipment
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY 2.17. Personal Protective Equipment The following Personal Protective Equipment (PPE) should be worn when operating or maintaining the equipment. Safety Glasses • Wear safety glasses at all times to protect eyes from debris. Coveralls •... -
Page 16: Safety Decals
2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR First-Aid Kit • Have a properly-stocked first-aid kit available for use should the need arise, and know how to use it. 2.19. Safety Decals • Keep safety decals clean and legible at all times. •... - Page 17 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Figure 2. Safety Decal Locations P1513136* P1513039** P1513045 P1513052 P1513037 P1513003 P1513042 P1513001 * if equipped with EPA gas tank ** if equipped with hand winch Figure 3. S-Drive Safety Decal Location P1513022 8210–00009 R1...
- Page 18 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 4. Gas Drive Safety Decal Locations (Over-Mount) Figure 5. Electric Drive Safety Decal Locations (Over-Mount) 8210–00009 R1...
- Page 19 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Figure 6. Gas Drive Safety Decal Locations (Under-Mount) Figure 7. Hydraulic Winch Decal Locations (If Equipped) P1513038 P1513038 P1513036 P1513036 8210–00009 R1...
- Page 20 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 8. Wheel Move Kit (1500 and 2000 Series) Decal Locations P1513036 P1513057 P1513058 P1513040 8210–00009 R1...
- Page 21 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Figure 9. Wheel Move Kit (1800 and 2400 Series) — Decal Locations 8210–00009 R1...
- Page 22 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Table 1. Safety Decals Part Number Description P1513003 DANGER ELECTROCUTION HAZARD To prevent death or serious injury: • When operating or moving, keep equipment away from overhead power lines and devices. •...
- Page 23 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Table 1 Safety Decals (continued) Part Number Description P1513045 WARNING OPEN BELT CONVEYOR To prevent death or serious injury: • DO NOT step on or touch moving conveyor belt. • Shut off and lock out power to adjust, service, or clean.
- Page 24 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Table 1 Safety Decals (continued) Part Number Description P1513001 WARNING To prevent serious injury or death: • Read and understand the manual before assembling, operating, or maintaining the equipment. • Only trained personnel may assemble, operate, or maintain the equipment.
- Page 25 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Table 1 Safety Decals (continued) Part Number Description P1513042 WARNING UPENDING HAZARD To prevent death or serious injury: • Anchor intake end and/or support discharge end to prevent upending. • Intake end must always have downward weight. Do not release until attached to tow bar or resting on ground.
- Page 26 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Table 1 Safety Decals (continued) Part Number Description P1513002 WARNING ENTANGLEMENT HAZARD To prevent serious injury or death: • Keep body, hair, and clothing away from rotating pulleys, belts, chains, and sprockets. •...
- Page 27 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Table 1 Safety Decals (continued) Part Number Description P1513009 WARNING ELECTROCUTION HAZARD To prevent serious injury or death: • Only qualified personnel should service electrical components. • Disconnect and lockout power before inspecting or servicing unit.
- Page 28 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Table 1 Safety Decals (continued) Part Number Description P1513040 WARNING TRANSPORT HAZARD To prevent serious injury or equipment damage, before towing: • Lift up wheel frame completely and secure with safety chain. •...
- Page 29 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 2. SAFETY Table 1 Safety Decals (continued) Part Number Description P1513052 NOTICE To prevent damage, wheels must be free to move when raising or lowering equipment. When equipment is positioned, chock all wheels. P1513061 NOTICE TAKE-UP ROLLER...
- Page 30 2. SAFETY S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Table 1 Safety Decals (continued) Part Number Description P1513049 IMPORTANT Lubricate belt release and motor mount sliders with silicone or light oil. P1513057 INTAKE DISCHARGE 8210–00009 R1...
-
Page 31: Features
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 3. FEATURES 3. Features Read this section to familiarize yourself with the basic component names and functions of the conveyor. ITEM DESCRIPTION ITEM DESCRIPTION Tube Hitch Tongue Holder A-Frame Hopper Hood Spout Assembly Belt Return and Weather Guard Hitch Jack... -
Page 32: Model Number
3. FEATURES S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 3.1. Model Number 8210–00009 R1... -
Page 33: Transport
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 4. TRANSPORT 4. Transport Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 4.1. Transport Safety • Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. -
Page 34: Connecting The Conveyor To The Towing Vehicle
4. TRANSPORT S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 3. Longer conveyors have a large turning radius. Allow ample room for turning as the discharge end may swing dramatically. Allow all oncoming traffic to pass before turning right or left. A collision with an oncoming vehicle could occur if the conveyor discharge swings into the opposing lane. -
Page 35: Placement
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 5. PLACEMENT 5. Placement Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 5.1. Placement Safety • The conveyor is not insulated, keep away from overhead power lines. Electrocution can occur without direct contact. -
Page 36: Positioning The Conveyor With A Mover Kit
5. PLACEMENT S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 10. Typical Grain Conveyor Placement for Filling Bins KEEP AWAY! OVERHEAD WIRES wheel chocks Under Hopper Bottom Bins 1. Center the conveyor between the hopper bin’s vertical legs. 2. Collapse the cloth hopper until the conveyor is fully positioned under the bin. 3. - Page 37 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 5. PLACEMENT Figure 11. Wheel Over-Center Handle Positions Engaged Disengaged 2. Set and run the gas engine at approximately half throttle. 3. Refer to the controls shown in Figure 12 on page 37 Figure 4.
- Page 38 5. PLACEMENT S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 13. Wheel Move Kit Controls (1800 and 2400 Series) If Operating the Wheel Move Kit in Temperatures Below -10°C (14°F): • Allow the hydraulic oil to warm before using the self-propelled kit. Failure to warm the hydraulic oil can damage the pump or other components.
-
Page 39: Hand Winch Operation
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 5. PLACEMENT Ensure that the over-center bolts are tight enough to prevent the handle from engaging. If they are not tight enough, damage to the gears and motor will result. 5.4. Hand Winch Operation When equipped with a Hand Winch: Before using the hand winch, ensure that: •... -
Page 40: Collapsible Hopper Cloth Control
5. PLACEMENT S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 3. Start the power source and idle at low rpm. Engage hydraulic lever to power winch. Test the direction of rotation of winch to ensure drum is moving in the direction required. Increase tractor rpm until desired rate of lift or descent is reached. - Page 41 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 5. PLACEMENT Table 3. Maximum Moving Angles for Grains Grain Maximum Conveyor Grain Maximum Conveyor Angle (degrees) Angle (degrees) Flax Wheat Lentils Alfalfa Pellets Mustard Barley Canola Canary Seed Oats Chickpeas Peas Corn Rice Shelled Corn (dry)
-
Page 42: Operation
6. OPERATION S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 6. Operation Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 6.1. Operation Safety • Keep away from rotating and moving parts, including the conveyor belt, drive components, shafts, and bearings. -
Page 43: Operation - Electric Motor Models
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 6. OPERATION 6.3. Operation - Electric Motor Models When equipped with an Electric Motor: 1. Turn the electric motor on. 2. Run until the conveyor is empty. 3. Turn off motor and lock out power source. 4. -
Page 44: Conveyor Belt Speed
6. OPERATION S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR • flood feed the hopper. Figure 15. Conveyor Loading Zone 6.6. Conveyor Belt Speed The best results are obtained when the conveyor belt speed is set at 600 to 700 ft/min on the 1500 series, and 600 to 650 ft/min on the 1800, 2000, and 2400 Series. -
Page 45: Shutdown
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 6. OPERATION Starting under load may result in damage to the conveyor. 2. If guards or covers have been opened or removed, close or replace them before restarting the unit. 3. If the auger tube is full of grain, it may be necessary to tighten the drive belts slightly to handle the heavier than normal loads. - Page 46 6. OPERATION S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Important Fertilizer weakens the belt lacing and warranty is void on all lacing used with fertilizer. The belt lacing may need to be replaced more often if you convey fertilizer. Additional Operating Requirements To prevent problems that can be caused by conveying fertilizer: 1.
-
Page 47: Storage
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 6. OPERATION Figure 16. Fertilizer Buildup on Rollers Figure 17. Fertilizer Buildup at Hopper Transition 6.12. Storage After the season’s use, the conveyor should be thoroughly inspected and prepared for storage. Repair or replace any worn or damaged components and perform maintenance as described in the Maintenance Section to prevent any unnecessary downtime at the start of the next season. - Page 48 6. OPERATION S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 5. Touch up all paint nicks and scratches to prevent rusting. 6. Check tire pressure and inflate. For inflation pressure, refer to Section 9. – Specifications on page 7. Inspect the conveyor for cracks, tightness of fittings and fasteners, hydraulic hose cracks (if applicable). Have required repairs performed to replace worn or damaged components.
-
Page 49: Maintenance
• After maintenance is complete, replace all guards, service doors, and/or covers. • Use only genuine AGI replacement parts or equivalent. Use of unauthorized parts will void warranty. If in doubt, contact AGI or your local dealer. Before attempting maintenance of any kind: •... -
Page 50: Visually Inspect The Equipment
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Section 7.8 – Inspect the Hopper Flashing on page 52 Section 7.9 – Check the Roller Bearings on page 52 Section 7.10 – Check the Rollers on page 52 Section 7.13 – Inspect Belt Lacing on page 56 Annually: Section 7.11 –... -
Page 51: Lubricate The Equipment
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE 9. Check all operating, lifting, and transport components. Replace damaged or worn parts before using the conveyor. 10. Inspect the winch cable for fraying, kinking, unwinding, or other possible damage. 7.4. -
Page 52: Inspect Hydraulic Hoses And Fittings
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7.7. Inspect Hydraulic Hoses and Fittings When equipped: 1. Pressurize the system. 2. Using a piece of cardboard or wood, run it along the length of the hose and around all fittings. Escaping hydraulic fluid under pressure will cause serious injury if it penetrates the skin surface. -
Page 53: S-Drive Pinch Roller
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE 2. Ensure the take-up roller is tensioned equally by using a tape measure to check the distance “X” on both sides. 3. After the conveyor belt has been tensioned, check the alignment of all s-drive rollers, see Section 7.12 –... -
Page 54: Align The Conveyor Belt
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 19. S-Drive Pinch Roller A — Drive Roller B — Pinch Roller 7.12. Align the Conveyor Belt Basic Conveyor Belt Alignment: The conveyor belt will run straight when all of the rollers are straight. Loosen or tighten the adjustment bolt(s) to align the conveyor belt. -
Page 55: Adjust The Rollers
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE Before Aligning the Belt: • The conveyor must be empty of all grain. • Wait until the belt makes a complete revolution before adjusting the rollers. Some belts may have uneven edges, appearing misaligned. -
Page 56: Adjust The Belt Return Wear Blocks
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 23. Rotate the Adjustment Bolt 3. Restart conveyor and run empty for 1 minute. 4. Stop the conveyor and remove ignition key or lock out the power source. 5. If the belt has centered, move to next step. If not, repeat Step 2 to Step 4 until the belt is centered. 6. -
Page 57: Replace The Belt Lacing
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE 7.14. Replace the Belt Lacing 1. Rotate the conveyor belt until the lacing is between the s-drive and the hopper. 2. Loosen the tension on the s-drive take-up roller all the way. 3. -
Page 58: Clean And Wash The Equipment
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Figure 25. Using the Ratchet Strap 9. Install the lacing pin and crimp the retainer clips onto each end of the lacing pin, see Figure 10. Remove the ratchet strap and tighten the conveyor belt (see “Tension the Conveyor Belt”). 11. -
Page 59: Tension The Drive Belts
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE 2. Make sure water can drain from the conveyor tube and intake, then wash the tube with a water hose or pressure washer until all dirt, mud, debris, or residue is gone. Important Do not contact electronic controls with high pressure washer. -
Page 60: Replace The Drive Belts
7. MAINTENANCE S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7.19. Replace the Drive Belts When equipped: 1. Remove the guard. 2. Fully loosen the drive belts. 3. Remove and replace the old belts. 4. Tighten the drive belts as described in Belt Tension. 5. -
Page 61: Pinion Gear Adjustment
S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 7. MAINTENANCE 4. Keep a film of grease on the gears. Occasionally oil the bushings, drum shaft, and ratchet. 5. Do not get oil or grease on brake discs. 6. Replace brake discs if less than 1/16" (1.6 mm) thick. 7. -
Page 62: Troubleshooting
8. TROUBLESHOOTING S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 8. Troubleshooting Shut down and lock out all power sources before diagnosing any of the causes or attempting any of the solutions below. In the following section, we have listed some causes and solutions to some of the problems you may encounter. - Page 63 Decrease belt speed, see Belt Speed in conveyor discharge plugging. Operation. between hood and belt. U-clamps or brackets U-clamps or brackets not Contact dealer or AGI to correct sliding on tube. properly crimped to tube. positioning. Drive Cause Problem Solution Drive making noise.
- Page 64 8. TROUBLESHOOTING S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR Mover Kit with Hydraulic Winch Lift Cause Problem Solution Valve is leaking. Loose/cracked fittings. Tighten/replace fittings. Worn hose. Replace hose. Valve spools are worn. Replace valve. Machine operates Oil is hot. Check oil level and add if required.
- Page 65 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 8. TROUBLESHOOTING Problem Cause Solution The conveyor will not The conveyor is already at its If at maximum height, lower the conveyor. raise or lower. maximum or minimum height. Obstruction in the slide. Clear the obstruction.
-
Page 66: Specifications
9. SPECIFICATIONS S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR 9. Specifications Up - Down - Operation Transport Belt Width Weight Model Length (ft) Elec (ft) (ft) (ft) (ft) 1545 FL 2305 20.8 21.6 22.1 20 HP 32 HP 107'2" 2045 FL 3775 23.5... -
Page 67: Limited Warranty
10. LIMITED WARRANTY 10. Limited Warranty This warranty relates to Belt Conveyors (the “Product”) sold by AGI (referred to herein as the “Seller”) and applies only to the first user of the Product (meaning a purchaser directly from the Seller or from an authorized dealer or distributor of the Product, referred to herein as the “Buyer”). - Page 68 Shipping: 201 Industrial Drive, Swift Current, Saskatchewan S9H 5R4, CANADA Mailing: Box 1750, Swift Current, Saskatchewan S9H 4J8, CANADA Toll-Free: (877) 667-7421 (Canada & USA) Phone: (306) 773-7779 Fax: (306) 778-2524 Web: www.aggrowth.com Email: sales@batco-rem.com ©Ag Growth International Inc. 2021 Printed in Canada If you have any comments or questions on this manual, or find an error, email us at comments@aggrowth.com.
Need help?
Do you have a question about the Batco FX 1500 Series and is the answer not in the manual?
Questions and answers