Warnings And Faults - ABB ACS580-01 Quick Installation And Start-Up Manual

Parameter
26.11 Torque ref1 source
28.11 Ext1 frequency ref1
58.01 Protocol enable
58.03 Node address
58.04 Baud rate
58.05 Parity
58.06 Communication control
Other parameters related to the fieldbus configuration:
58.14 Communication loss
action
58.15 Communication loss
mode
58.16 Communication loss
time

Warnings and faults

Warning Fault Aux. code
A2A1 2281 Current calibration
A2B1 2310 Overcurrent
A2B3 2330 Earth leakage
A2B4 2340 Short circuit
- 3130 Input phase loss
- 3181 Wiring or earth fault
A3A1 3210 DC link overvoltage
A3A2 3220 DC link undervoltage
- 3381 Output phase loss
- 5090 STO hardware failure
A5A0 5091 Safe torque off
A7CE 6681 EFB comm loss
A7C1 7510 FBA A communication
A7AB - Extension I/O
configuration failure
AFF6 - Identification run
- FA81 Safe torque off 1
- FA82 Safe torque off 2
Ratings, fuses and typical power cable sizes
ACS580-
Nominal ratings
01-...
Input Output
current current
I I
1 2
A A
U = 200...240 V, P at U = 3-phase 208/230 V, 60 Hz
1 n n
04A6-2 4.6 4.6
06A6-2 6.6 6.6
07A5-2 7.5 7.5
10A6-2 10.6 10.6
017A-2 16.7 16.7
024A-2 24.2 24.2
031A-2 30.8 30.8
046A-2 46.2 46.2
059A-2 59.4 59.4
075A-2 74.8 74.8
088A-2 88.0 88.0
114A-2 114 114
143A-2 143 143
169A-2 169 169
211A-2 211 211
Setting Description
EFB ref1 Selects a reference received through the embedded fieldbus interface
as torque reference 1. Use this parameter with the vector motor
control mode.
EFB ref1 Selects a reference received through the embedded fieldbus interface
as frequency reference 1. Use this parameter with the frequency motor
control mode.
Modbus RTU Initializes embedded fieldbus communication.
1 (default) Node address. There must be no two nodes with the same node
address online.
19.2 kbps (default) Defines the communication speed of the link. Use the same setting as
in the master station.
8 EVEN 1 (default) Selects the parity and stop bit setting. Use the same setting as in the
master station.
Refresh settings Validates any changed EFB configuration settings. Use this after
changing any parameters in group 58.
58.17 Transmit delay
58.25 Control profile
58.26 EFB ref1 type
Description
Warning: Current calibration is done at the next start.
Fault: Output phase current measurement fault.
The output current is more than the internal limit. This can also be caused by
an earth fault or phase loss.
A load unbalance that is typically caused by an earth fault in the motor or the
motor cable.
There is a short-circuit in the motor or the motor cable.
The intermediate DC circuit voltage oscillates due to missing input power
line phase.
Incorrect input and motor cable connection.
Intermediate DC circuit voltage is too high.
Intermediate DC circuit voltage is too low.
All three phases are not connected to the motor.
STO hardware diagnostics has detected hardware failure. Contact ABB.
The Safe torque off (STO) function is active.
Break in embedded fieldbus communication.
Communication lost between drive (or PLC) and fieldbus adapter.
The installed C-type module is not the same as configured, or there is an
error in the communication between the drive and module.
The motor ID run occurs at the next start.
The Safe torque off circuit 1 is broken.
The Safe torque off circuit 2 is broken.
Motor gG fuse
1)
power (IEC 60269)
P
n
ABB type
kW hp
0.75 1.0 OFAF000H25
1.1 1.5 OFAF000H25
1.5 2.0 OFAF000H25
3.0 3.0 OFAF000H25
4.0 5.0 OFAF000H25
5.5 7.5 OFAF000H40
7.5 10.0 OFAF000H40
11.0 15.0 OFAF000H63
15 20 OFAF000H63
15 25 -
22 30 OFAF00H125
30 40 OFAF00H125
37 50 OFAF0H200
45 60 OFAF0H250
55 75 OFAF1H315
58.28 EFB act1 type
58.31 EFB act1 transparent
source
58.33 Addressing mode
3)
Fuses
uR/aR UL class
2)4) 5)6)7)
fuse T
(DIN 43620)
Bussmann type
170M1563 JJS-15
170M1563 JJS-15
170M1563 JJS-15
170M1563 JJS-15
170M1563 JJS-30
170M1565 JJS-40
170M1565 JJS-40
170M1566 JJS-80
170M1566 JJS-80
- JJS-100
170M3815 JJS-150
170M3815 JJS-150
170M3817 JJS-200
170M5809 JJS-250
170M5810 JJS-300
58.34 Word order
58.101 Data I/O 1
...
58.114 Data I/O 14
Typical power cable sizes,
Cu
2 8) 9)
mm AWG
3×1.5 + 1.5 14
3×1.5 + 1.5 14
3×1.5 + 1.5 14
3×1.5 + 1.5 14
3×2.5 + 2.5 10
3×4.0 + 4.0 8
3×6.0 + 6.0 8
3×10 + 10 6
3×10 + 10 4
- 3
3×35 + 16 2
3×50 + 25 1/0
3×70 + 35 3/0
3×95 + 50 4/0
3×120 + 70 300 MCM
12
Frame
size
R1
R1
R1
R1
R1
R2
R2
R3
R3
R4
R5
R5
R6
R7
R7