Using The Remote Control; Drying - Toto WASHLET SW3084T40 Instruction Manual

Basic Operation
Operate the controls on the remote control; a beep sounds when the main unit
receives the signal.
Stopping
"Stopping"
Stops the operation.
Cleansing
"Rear cleansing"
Cleanses your rear.
"Rear soft cleansing"
Cleanses your rear with
mild water pressure.
 The setting changes between
and each time the is pressed.
"Front cleansing"
Serves as a bidet for ladies.

Drying

"Warm air drying"
Dries your rear.
"Wand CLEAN"
Cleans the wand with "EWATER+".
 The wand can be automatically
cleaned when you use the
cleansing functions (Rear cleansing,
Front cleansing, etc.). (Page 16)
"Personal setting lock"
You can store your preferred "Wand position", "Water
pressure" and "Warm water temperature" settings.
● To store a settings
While cleansing is in progress, set your preferred "Wand position",
"Water pressure" and "Warm water temperature" and then press
and hold or for 2 seconds or longer.
● To use
Press or , and then press the button for the cleansing you want to use.
 The "Wand position" and "Water pressure" lamps will light up for about 10
seconds in their set positions, and the "Water temperature" display switches.
*1 Remote control transmitter (Front side, Top side)
18

Using the Remote Control

● Functions that operate when a
button is pressed during "Rear
*1
cleansing", "Rear soft cleansing"
or "Front cleansing" cleansing.
Note
 Sitting back on the toilet seat
makes it easier to adjust the wand
position and to reduce splashing.
"Oscillating cleansing"
The wand moves back and forth
to cleanse your rear thoroughly.
"Pulsating cleansing"
Cleanses with the water pressure
pulsating between soft and strong.
 The setting changes between "ON" and
"OFF" each time the button is pressed.
"Water pressure adjustment"
You can adjust the water pressure
to one of fi ve levels.
([-] Softer, [+] Stronger)
 After you press the "Water pressure
adjustment" button, the set position
will light for 10 seconds."
 It will return to the 3rd position for
a while (not exceeding a maximum
of 5 minutes) once operation of
the remote control has fi nished.
"Wand position adjustment"
You can adjust the washing position to
5 diff erent points between the front and
the rear, using the [▲] and [▼] buttons.
 After you press the "Wand position
adjustment" button, the set position
will light for 10 seconds."
 It will return to the 3rd position for
a while (not exceeding a maximum
of 5 minutes) once operation of
the remote control has fi nished.
This section is an overview of the settings that can be confi gured with the remote control.
See the corresponding pages for the detailed descriptions.
Temperatures
Remote control back side
Adjust temperatures (Page 20)
"Toilet seat
temperature"
"Warm water
temperature"
"Drying air
temperature"
"Power ON/OFF"
Pressing it about 3 seconds or longer
turns the power on/off .
• If the remote control is secured to
prevent theft (Page 15 2-2)
For your information
●Water may sometimes come out from around the wand when it expands in the warm water tank, but this is
normal.
●As the warm water tank of hot-water system is used, the temperature of warm water may become lower if it is
continuously consumed.
Energy saver
Saving energy (Page 24, 25)
"Timer energy
saver"
"Auto energy
saver"
"Setting
confi rmation"
 The current setting can be
discerned from the LEDs.
"Wand cleaning"
 To clean the wand with it extended.
(Page 36)
Low battery warning
mark
(Page 38)
19