However, like all electronic equipment, the AV-GM08Z3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
INTRODUCTION The AV-GM08Z3-S1 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4 provides the most flexible and cost effective solution in the market to route high definition video source from any of the four FHD HDMI sources to the remote display at the same time.
Page 4
1x Installation software CD 1x User Manual 1x IR Remote control (28 keys) 1x IR Receiving cable ...
SPECIFICATIONS Model Name AV-GM08Z3-S1 Technical Role of usage Multiplexer / video processor Background picture update HDCP compliance Input: HDMI 1.4 HDMI compliance Output: HDMI 2.0a Input: HDMI [2.25G to 6.75Gbps] Video bandwidth Output: Single-link 600MHz [18Gbps] Up to 4K2K@60 (4:4:4 8bits)
HARDWARE INSTALLATION AV-GM08Z3-S1 as master 1. Connect all sources to HDMI Inputs on the AV-GM08Z3-S1. 2. Connect the display to HDMI Output on the AV-GM08Z3-S1. 3. Connect the +12V 5A DC power supply to the AV-GM08Z3-S1. CONNECTION DIAGRAM...
PANEL DESCRIPTIONS AV-GM08Z3-S1 Front Panel LABEL: All Windows label on/off FULL SCREEN: Switch Window in full screen mode Windows Source Selection A-D: Window A-D source selection Default Layout PAP: Four different default layout PAP mode IR SENSOR: IR sensor for receiving the IR commands from IR remote Rotation: Window A rotate °...
OPERATION APPROACH Method A: IR Remote Control Button Function HDMI/DVI mode switch Reserved Reserved Power on/off the device Window A rotate 90 ° or Rotation -90° Label Window label on/off Fast Switch output’s audio Sound channel To set up the background Background picture of window Select 4K2K output...
Page 9
Method B: Software Control through RS-232 port / Ethernet port System Requirement and Precautions 1. Whenever power off AV-GM08Z3-S1, please stay unpowered at least 5 to 10 seconds to allow power capacitors to discharge. 2. The AV-GM08Z3-S1 provides software control program which runs under Microsoft Windows 98, 2000, XP, 7, 8 through the interface of RS-232 serial control.
Page 10
Control Interface 1. Connection Status: Show the connect information and status. If users use RS-232 serial Mode to connect device, the graph is . In contrast, the graph of Ethernet is . In addition, if users would like to change the control method, users can click on the button to change.
Page 11
(2) Quick Selection We provide 9 default modes and 8 custom modes for you to select. (3) Output Resolution Set the output resolution. If user click the 1080p to 4K2K function, when output resolution is 1920 x 1080 @60Hz, it will upscale the resolution to 4K2K. *In 4K2K@60Hz resolution, the output display will be forced to PAP 1 ( ) layout (other PAP layout cannot set) and only can set up the output resolution, sound and...
Page 12
(4) Save Layout We provide 8 custom layout space for users to save the frequently used scenarios into the flash memory. (5) Display Panel In the left part of control interface, user can customize the display mode thru control. The different colors of frame represent the different input windows. The information of coordinate shows the position of input source screen.
Page 13
3. Advanced Setting (1) Window settings In this mode, user can adjust individual display area for selected input sources. Firstly, user have to choose the specific channel A, B, C, or D, which are presented as in the control panel as shown. After the specific channel is chosen, user can crop the display area of that particular channel at will and do the same to the rest of channels if necessary.
Page 14
(4) Background To set up the background of window. We provide 4 default pictures for you to select. If you want to change default picture, you can click the button to select the picture which you want to change. (5) Window Label In this function, users can determine if the window’s label/border is turned on or off.
Page 16
(1) Learn EDID from Default Select Default EDID Select Input Click button to learn default EDID. (2) Learn EDID from File Select input Click button to select the EDID file and write it into input 5.
Page 17
(5) Firmware Update Click button to do firmware update. The “Firmware update” window shows up as below. Please select the correct COM port or click “Scan” button to connect device. Click “update” button to do firmware update. ...
Page 18
If you want to change OSD (window label) font, please click “OSD Font Update” and “update” buttons to change OSD font. (5) Factory Reset Click button to do factory default reset. The process of default reset will take about 25 seconds. ...
Page 19
6. IP Configure User also can use the Ethernet to control the mixer. Firstly, user should click on the button button to setup network set. Next, users can setup the Ethernet for the unit as below example shows. After the step of IP configuration, please click the button.
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM08Z3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM08Z3-S1 and is the answer not in the manual?
Questions and answers