Related Manuals for Pilz PSSu E S PD-D
Summary of Contents for Pilz PSSu E S PD-D
- Page 1 PSSu E S PD-D Decentralised system PSSuniversal I/O Operating Manual 21975-EN-05...
- Page 2 Preface This document is a translation of the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for internal purposes. Suggestions and comments for improving this documentation will be gratefully received.
-
Page 3: Table Of Contents
Changing an electronic module during operation Section 6 Wiring General wiring guidelines 6.1.1 Mechanical connection of the base modules Terminal configuration Section 7 Operation Messages Display elements 7.2.1 Display elements for module diagnostics Operating Manual PSSu E S PD-D 21975-EN-05... - Page 4 Contents 7.2.2 Display elements for output status Section 8 Technical Details Section 9 Order reference Product Accessories Operating Manual PSSu E S PD-D 21975-EN-05...
-
Page 5: Operating Manual Pssu E S Pd-D
Introduction Introduction Validity of documentation This documentation is valid for the product PSSu E S PD-D. It is valid until new documenta- tion is published. This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. -
Page 6: Definition Of Symbols
It also highlights areas within the text that are of particular import- ance. INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 7: Overview
LEDs for: – Switch status of each output – Module error The module provides advanced diagnostic data. Optional access to the advanced diagnostic data in the process image (system environ- ment A only) Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 8: Front View
2D code 3: Labelling strip for the terminal configuration on the base module 4: Status LEDs 5: Name of electronic module 6: Connection level 1 7: Connection level 2 8: Connection level 3 Operating Manual PSSu E S PD-D 21975-EN-05... - Page 9 11: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal lines 12: Mounting slot for colour marker to label the connection level (connection levels 1, 2, 3 and 4) Operating Manual PSSu E S PD-D 21975-EN-05...
-
Page 10: Safety
PAS4000 from version 1.8.0 – We recommend that you always use the latest version (download from www.pilz.de). The PSSu E S PD-D module may be used in conjunction with the following base modules: PSSu BP 1/8 S PSSu BP 1/8 C... -
Page 11: Safety Regulations
In safety-related applications, please comply with the mission time T in the safety-re- lated characteristic data. When decommissioning, please comply with local regulations regarding the disposal of electronic devices (e.g. Electrical and Electronic Equipment Act). Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 12: Function Description
20 ms if the supply voltage is interrupted. The module provides the following diagnostic data: Start-up error Configuration error ST communication error Bus termination error Output overload Temperature error: too warm Temperature error: too hot Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 13: Configuration
Overload on output S3 No overload on output S4 Overload on output S4 No temperature error Temperature error: too warm Switch-off temperature not reached. Temperature error: too hot. Outputs switch off. Reserved Reserved Reserved Reserved Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 14: Pssu Assignment In System Environment B
Function description 4.3.2 PSSu assignment in system environment B The module does not have to be configuriert. Status information is not available in the pro- cess image. Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 15: Installation
5.1.1 Dimensions Base modules with four connection levels: 12,6 mm 8,1 mm 52,1 mm (0.496") (0.319") (2.051") 12,6 mm 72,6 mm (0.496") (2.858") Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 16: Installing The Base Module
Push the base module back [2] until you hear it lock into position. On the mounting rail, slide the base module to the left until you hear the two lateral mounting hooks on the adjacent module lock into position [3]. Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 17: Inserting And Removing An Electronic Module
This is how the base module is coded. The mechanics of the electronic modules are designed for 50 plug in/out cycles. Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 18: Inserting An Electronic Module
Installation 5.3.1 Inserting an electronic module Procedure: The electronic module must audibly lock into position [1]. Mark the electronic module using the labelling strips [2]. Schematic representation: Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 19: Removing An Electronic Module
– The substitute values are used for the modules' FS outputs, with Valid Bits = FALSE. CAUTION! Sparking can cause interference and errors! Only change the module when the load is switched off! Operating Manual PSSu E S PD-D 21975-EN-05... -
Page 20: Wiring
Insert the screwdriver [4] into the square hole [1]. – Insert the stripped cable into the round fixing hole [2], as far as it will go [5]. – Pull out the screwdriver [6]. – Check that the cable is firmly seated. Operating Manual PSSu E S PD-D 21975-EN-05... - Page 21 To crimp the ferrules you can use crimp pliers (crimp form A or C) conforming to EN 60947-1, such as the PZ 1.5 or PZ 6.5 from Weidmüller, for example. – Maximum torque setting: 0.8 Nm Operating Manual PSSu E S PD-D 21975-EN-05...
-
Page 22: Terminal Configuration
PSSu BP-C 1/8 C 21: Output S2 12 -22: 0 V periphery supply (12-22 linked within the base module) 13 -23: C-rail supply (13-23 linked within the base module) 14: Output S3 24: Output S4 Operating Manual PSSu E S PD-D 21975-EN-05... - Page 23 (13-23-16-26 linked within the base module) 14: Output S3 24: Output S4 15 -25: 0 V periphery supply (15-25 linked within the base module) 16 -26: C-rail supply (13-23-16-26 linked within the base module) Operating Manual PSSu E S PD-D 21975-EN-05...
-
Page 24: Operation
After the "too hot" message has been received, if the temperature drops back below the "too warm" theshold value, the outputs will switch back on. Further information on PSSu error messages is available in the online help for the PSSuni- versal Assistant system software. Operating Manual PSSu E S PD-D 21975-EN-05... - Page 25 No overload on out- put S2 - - - Overload on output green No overload on out- put S3 - - - Overload on output green No overload on out- put S4 Operating Manual PSSu E S PD-D 21975-EN-05...
- Page 26 In accordance with the standard EN 60068-2-30, EN 60068-2-78 Humidity 93 % r. h. at 40 °C Not permitted Condensation during operation EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61131-2 Operating Manual PSSu E S PD-D 21975-EN-05...
- Page 27 Material Bottom Front Coding Dimensions Height 76,0 mm 12,6 mm Width Depth 60,2 mm Weight 34 g Mechanical coding Type Colour Dark grey Where standards are undated, the 2008-04 latest editions shall apply. Operating Manual PSSu E S PD-D 21975-EN-05...
- Page 28 Base module without C-rail with cage clamp terminals 312 619 PSSu BP-C1 1/12 S Base module with C-rail and screw terminals 312 622 PSSu BP-C1 1/12 C Base module with C-rail and cage clamp terminals 312 623 Operating Manual PSSu E S PD-D 21975-EN-05...
- Page 29 Front cover Support Technical support is available from Pilz round the clock. Americas Australia Scandinavia Brazil +61 3 95446300 +45 74436332 +55 11 97569-2804 Spain Canada Europe +34 938497433 +1 888-315-PILZ (315-7459) Austria Switzerland +41 62 88979-30 Mexico +43 1 7986263-0...