Safety Notices; Industry Canada Notice; Fcc Statement - AudioCodes MediaPack MP-114 Quick Installation Manual

Quick Installation Guide
•
Installation and service of this unit must only be performed by authorized, qualified service personnel.
•
The MediaPack FXO Output Tones and DTMF level should not exceed -9 dBm (AudioCodes setting #23) in order to comply
with FCC 68, TIA/EIA/IS-968 and TBR-21.
•
The maximum allowed gain between any 2 ports connected to the PSTN should be set to 0 dB in order to comply with FCC
68, TIA/EIA/IS-968 Signal power limitation.
This equipment meets the applicable Industry Canada Terminal Equipment technical specifications. This is confirmed by the
registration numbers. The abbreviation, IC, before the registration number signifies that registration was performed based on a
declaration of conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry
Canada approved the equipment.
The Ringer Equivalence Number (REN) for this terminal is 0.5. The REN assigned to each terminal equipment provides an
indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of Ringer Equivalence Number
of all devices do not exceed five.
The products support the Telecom networks in EU that comply with TBR21.
The safety status of each port is declared and detailed in the table below:
Circuit whose normal operating voltages exceeds the limits for an SELV circuit under normal operating conditions
TNV-3:
and on which over voltages from Telecommunication Networks are possible.
Safety extra low voltage circuit.
SELV:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment, the VoIP Analog Gateway, models MP-118, MP-114 and MP-112 complies with Part 68 of the FCC Rules and
1.
the requirements adopted by the ACTA. On the bottom of the unit of this equipment is a label, that contains among other
information, a product identifier in the format US:AC1IT00BMP11X3AC. If requested, this number must be provided to the
telephone company.
This equipment is designed to be connected to the telephone network using an RJ-11C connector, which is Part 68 compliant.
2.
The service order code (SOC) is 9.0Y and the Facility interface code (FIC) is 02LS2.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a
3.
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the format
US:AC1IT00BMP11X3AC The digits represented by 00 are the REN without a decimal point.
Should the product causes harm to the telephone network, the telephone company will notify you in advance that temporary
4.
discontinuance of service may be required. If advance notice is not practical, you will be notified as soon as possible. Also, you
will be advised of your right to file a compliant with the FCC if it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation
5.
of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information please contact AudioCodes Inc., 2099 Gateway
6.
Place, Suite 500, San Jose, CA, 95110, phone number 1-408-441-1175. If the equipment is causing harm to the telephone
network, the telephone company may request to disconnect the equipment until the problem is resolved.
Installation is described in the Product User's manual. Connection to Telephone Company-provided coin service is prohibited.
7.
Connection to party lines service is subject to State tariffs.
Version 5.0

Safety Notices

Industry Canada Notice

Network Compatibility
Telecommunication Safety
Ports
Ethernet (100 Base-TX)
FXO

FCC Statement

ACTA Customer information
43
7. Regulatory Information
Safety Status
SELV
TNV-3
September 2007