Table of Contents
Advertisement
to use crop encoding
1. Select <enable>.
2. Click <Set area>.
The Crop Encoding Area Setup window will pop up.
• 16:9 : The aspect ratio shall be set to 16:9 as close as to
the user specified area.
The supporting size ranges from 640X360 to 1280X720
and supporting output resolutions are 640X360, 800X448,
1280X720.
• 4:3 : The aspect ratio shall be set to 4:3 as close as to the
user specified area.
The supporting size ranges from 320X240 to 1280X960
and supporting output resolutions are 320X240, 640X480,
800X600, 1024X768, and 1280X960.
• Manual : It sets up the aspect ratio of the user specified
area.
The supporting size ranges from XNO-6080R: 320X240 ~ 1280X1024 / XNO-8080R: 320x240 ~
1600x1200 and all supporting output resolutions are available except 1920X1080.
3. Drag the mouse on the screen to specify the Crop Encoding area at your discretion.
If you set output as <Manual>, you can specify a desired range. However, if output is only available at a supported resolution,
`
J
the image will be output at the resolution that is closest to the range that you specified.
The Crop Encoding area setup can change depending on the DIS setup. Reset the Crop Encoding area when the DIS setup is
`
changed.
user
1. From the Setup menu, select the <Basic (
2. Click <user>.
3. Provide the necessary user information.
• Administrator password change : Change the password
for the administrator.
For the security purposes, you are recommended to use a
`
J
combination of numbers, alphabets uppercase and lowercase
and special characters for your password.
It is recommended to change your password once every three
`
months.
The password length and limits are shown as follows.
`
-
A combination of at least three types of upper case, lower case, numeric, and special characters: 8 to 9 characters.
-
A combination of at least two types of upper case, lower case, numeric, and special characters: 10 to 15 characters.
-
Should be different from the ID.
-
Cannot repeat the same letter, number of special characters more than 4 times.
-
Don't use 4 or more characters consecutive together. (examples : 1234, abcd)
-
Don't use 4 or more characters repeated. (examples : !!!!, 1111, aaaa)
-
Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
-
After the factory setting, the admin and user passwords are initialized. You need to reset the password.
-
When you access the camera web page for the first time or access it after the initialization, you will be moved to the
admin password setting menu.
-
In this menu, you need to login again with the new password before using the camera web page menus.
-
If the existing password is not matched, when you change the admin password, you cannot change the password.
-
After changing your password, if there is a camera connected to a CMS or NVR client, then you need to re-register it
with the newly changed password. If the camera is still connected with the same password, then the account may be
locked because a client uses the previous password.
If you try to login with the registered account, 5 or more consecutive password authentication has failed, and then the
`
account may be locked for thirty seconds.
When the password is changed while multiple connections are active from a PC, the browser may malfunction. In that
`
case, reconnect to the server.
• Guest setup : If you select <enable guest access>, the guest account can access the Web viewer
screen but can only view the live Viewer screen.
The ID/password for the guest account is <guest/guest>, which cannot be changed.
`
• Authentication setup : If you select <enable rtSp connection without authentication>, you can
access RTSP without logging in and view the video.
)> tab.
English _29
Advertisement
Table of Contents
