Page 2
15. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your Paramount dealer or Paramount Fitness Corp. at (800)721-2121 or www.paramountfitness.com. Refer to Maintenance Schedule label on machine for when to schedule maintenance.
MAINTENANCE 1. Frames: Wipe all machines down with a damp cloth and dry completely each day. This includes painted, chrome parts and upholstered pads. 2. Painted/chrome parts: Use Simple Green or similar cleaner for light dirt and grime. Use TurtleWax® Polishing Compound or a good car polish to remove heavier dirt and grease as well as for polishing.
Page 7
HARDWARE BOX FL-33: 3/8-16 x 1 1/2 HHCS 3/8-16 x 1 BHCS 3/8 Split Washer 3/8 Black Washer 3/8 Metal Baser 3/8-16 Locknut 3/8 Black Washer 3/8 Metal Base 3/8-16 x 3 HHCS Plastic Cover for 3/8 3/8-16 x 2 3/4 HHCS...
Page 8
04-1836 04-1837 04-1838 G (2) 04-1839 H (2) F (2) NOTE: WHEN INSTALLING HARDWARE, TIGHTEN BY HAND ONLY UNTIL ALL COMPONENTS ARE ASSEMBLED. BOLT HEADS SHOULD FACE TO OUTSIDE OF MACHINE WHERE POSSIBLE. BE SURE ALL HARDWARE IS TIGHT BEFORE USING MACHINE.
Page 9
F (2) 04-1840 G (2) 02-1928 (2) 13-0211 06-0025 (6) R (5) To Weight Stack Diagram A Diagram A V (4) 06-0430 (2) 03-0681 (2) 05-0492 MAKE SURE NUT IS TIGHT! 04-1843...
Page 10
04-1841 04-1842 06-0431 Diagram B Note: Adjust thumb screw to level the machine and remove rocking. C 451 C 955A (2) C 754B (2) C 766A C 955 Diagram B V (4) 06-0025 05-0492 04-1844 13-0207 06-0430 (2) 03-0681 (2) Diagram C MAX! 1 3/8”...
06-0561 (2) 10-0302 (2) PAD SEAM 06-0546 (2) LOCATION 07-0247 C 766A (2) C 955 (2) C 754B (2) C 955A (if needed) T (2) WEIGHT STACK INSTALLATION Review the equipment order to determine the weight stack configuration. The P/N: B1602 boxes are marked with the quantity and Comprised of weight of the plates.
Page 12
NOTE: TIGHTEN HARDWARE BY HAND ONLY AT THIS POINT. 13-0211 10-0273+ 10-0274 11-0090 NOTE: PARAMOUNT SELECTOR PIN 11-0090 IS THE ONLY PIN THAT SHOULD BE USED WITH THIS MACHINE. UNDER NO CIRCUM- STANCES SHOULD THE CAP PLATE OR WEIGHT STACK BE PINNED IN AN ELEVATED POSITION.
Page 13
B (2) 06-0545 05-0601 (2) 3” (7.6cm) 10-0273+ 10-0274 NOTE: MOVE CAP PLATE 10-0273+10-0274 UP TO PULLEY HOUSING TO SET THE CORRECT GUIDE ROD AND BRACKET SPACING. NOW COM- PLETELY TIGHTEN HARDWARE. CAP PLATE SHOULD MOVE SMOOTHLY ALONG GUIDE RODS. IF NOT, LOOSEN HARDWARE AND RESET SPACING. MAKE SURE MAX! LOCKING NUT...
Page 14
ITNESS WEIGHT STACK LABELS The FL-33 Hardware Box is packed with a weight stack number label set. Follow the instruc- tions printed on the label. Below is a list of weight stacks and the corresponding label set part numbers: Wt. Stack...
WARNING LABELS The following warning labels are affixed to the FL-33. Be certain that you and the facility staff are aware of the meaning and importance of each label. If the labels become damaged, replacements can be ordered free of charge from Paramount.
Paramount. This limited warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. Contact Paramount Fitness Corp., 6450 E. Bandini Blvd., Los Angeles, California 90040-3185, for a list of authorized dealers or before returning any defective equipment.