Page 2
AFETY 1. Review and understand all of the warning labels affixed to the machines and the facility safety sign. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from Paramount free of charge. 2.
Page 3
MAINTENANCE 1. Frames: Wipe all machines down with a damp cloth and dry completely each day. This includes painted, chrome parts and upholstered pads. 2. Painted/chrome parts: Use Simple Green or similar cleaner for light dirt and grime. Use TurtleWax® Polishing Compound or a good car polish to remove heavier dirt and grease as well as for polishing.
Page 6
HARDWARE BAG 1801-3: B 460 B 900 (3) 8001593 (4) 8001594 (4) B 898 B1295 (2) HARDWARE BAG 1801-2: B4003 (2) B1136 B 931 (2) B 921 (4) B 447 B1036 1801597 B 582 (2) B1182 B 682 (5) B1150 (2) MINIMUM FLOOR AREA REQUIRED: MACHINE WEIGHT (NOT INCLUDING WEIGHT OF USER):...
Page 7
HARDWARE BAG 1801-1: 3/8-16 x 3/4 BHCS 3/8 Lock Washer 3/8-16 x 1 BHCS 3/8-16 x 1 BHCS 3/8 Washer 3/8 Black Washer 3/8-16 Split Lockwasher 3/8-16 Locknut 3/8 Black Washer (2) 3/8 Metal Base Plastic Cover for 3/8 3/8-16 x 2 3/4 HHCS Plastic Cover for 3/8 3/8-16 X 3 3/4 HHCS 3/8-16 x 4 HHCS...
Page 8
TOP VIEW NOTE ORIENTATION OF PULLEY HOUSING NOTE: STABILIZER FOOT MUST BE ATTACHED TO THE MACHINE! 1801510X 8093040 1801535 1801540X D (2) NOTE: WHEN INSTALLING HARDWARE, TIGHTEN BY HAND ONLY UNTIL ALL COMPONENTS ARE ASSEM- BLED. BOLT HEADS SHOULD FACE TO OUTSIDE OF MACHINE WHERE POSSIBLE.
Page 9
1896015X C 955, C 754B, C 678, 1801520 C 766A, C 955A E (2) B4003 C 754B, C749, C678 1896085 D 869 1801505X 1801530x C [4] 1896015x Bushing Side! 1801525x 1801610 D593 D836 1-2 As Needed B1150 [2] D591 IF NEEDED IMPORTANT !!! BACK VIEW Follow the above layout when assembling...
Page 10
Diagram A 1801570X G (2) 1801580X B1295 (2) C 417 1/4-20 x 2 1/2 C 752 (2) C 740 Diagram A C 955 C 474 C 956 C 755 (2) C 766 1801550X D1017...
Page 11
8001594 8001510X 1801595 C 955 C 766A M (2) C 955A C 754B 1801598 N (2) 1801560X B4003 1801555X M (2) 8001594 (2) 1801590 C 955 (2) 8001125X (2) C 766A (2) C 955A (2) C 754B (2) (If Needed) 8001593 (2) WEIGHT STACK INSTALLATION Review the equipment order to determine...
Page 12
FRONT VIEW NOTE: TIGHTEN HARDWARE BY B (2) HAND ONLY AT THIS POINT. B 447 9000801X 9099780X NOTE: COUNTER C 461 WEIGHTING OF ARM C 955 (2) ASSY. REQUIRED. C 955A (2) C 754B C 766A WEIGHT PLATES C 757 (2) B 582 (2) NOTE: MOVE CAP PLATE 9099780X UP TO PUL- LEY HOUSING TO SET THE CORRECT GUIDE ROD...
Page 13
B 898 1801600 B 900 (3) R (3) 1801600 C 685A C 731 C 753 Note: Make sure cable connector moves freely. 1801599 (2) C 754B (2) C 911 (2) MAX! MAKE SURE LOCKING NUT 1801600 IS SECURE! 1 3/8” (35mm) B 460 NOTE: PARAMOUNT SELECTOR PIN B 460 IS THE ONLY PIN THAT SHOULD BE USED WITH...
Page 14
ELECT ITNESS WEIGHT STACK LABELS EIGHT TACK ABEL NSTALLATION Hardware Bag 1801-3 is packed with a weight stack number label set. Follow the instruc- tions printed on the label. Below is a list of weight stacks and the corresponding label set part numbers: Wt.
WARNING LABELS The following warning labels are affixed to the SF-1800. Be certain that you and the facility staff are aware of the meaning and importance of each label. If the labels become damaged, replacements can be ordered free of charge from Paramount.