Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron MMK-4L
Summary of Contents for Crestron MMK-4L
- Page 1 Crestron MMK-4L & WMKM-4L Mud Mount Kits Installation Guide...
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc.
-
Page 3: Supplied Hardware
The MMK-4L consists of three parts. These parts produce an assembly that attaches to the PMK-4L or BB-4L. The WMKM-4L consists of five parts–three of which make up the MMK-4L–as well as one mounting plate and one cutout template. The mounting plate provides the necessary support for post-construction applications. - Page 4 Supplied Hardware of the MMK-4L and WMKM-4L Dimensional Drawings 5.55 in (14.10 cm) 5.09 in (12.93 cm) 2 • Mud Mount Kits: MMK-4L & WMKM-4L Crestron MMK-4L & WMKM-4L DESCRIPTION Metal Plate, Mounting (WMKM-4L only) Metal Plate, Mud Ring Metal Plate, Adjustment...
-
Page 5: Installation
The procedure in this section provides the necessary steps for the assembly of the MMK-4L to either the PMK-4L or BB-4L. It is assumed that the PMK-4L or BB-4L has been secured to the stud according to the procedures in their latest Installation Installation Guide –... - Page 6 CAUTION: Allow an air gap of at least 12 inches in the wall cavity above and below the touchpanel for heat dissipation. NOTE: The illustrations in this procedure show the installation of the MMK-4L with the PMK-4L. Even though the illustrations only show the PMK-4L, they are identical for the BB-4L as well.
- Page 7 THAN ½ INCH. MUD RING PLATE (2013240) 5. When the mud ring plate is in position, bend the top two flanges of the plate upward and the bottom two flanges downward. • If mounting into the PMK-4L, bend the flanges approximately 90 degrees.
- Page 8 NOTE: Make the cutout as level as possible. The mounting plate allows for only minor leveling adjustments. 6 • Mud Mount Kits: MMK-4L & WMKM-4L Crestron MMK-4L & WMKM-4L 1. Insert the two pins on one adjustment plate into the top two outer holes on the mounting plate, as shown in the following illustration.
- Page 9 The screws pass through the clearance holes in the plate and are secured in the extruded holes of the adjustment plates. 11. Verify that the plate is level before tightening. Mud Mount Kits: MMK-4L & WMKM-4L • 7 Mud Mount Kits...
-
Page 10: Further Inquiries
For assistance in your local time zone, refer to the Crestron website (www.crestron.com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. -
Page 11: Return And Warranty Policies
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. - Page 12 Crestron Electronics, Inc. Installation Guide – DOC. 6389 15 Volvo Drive Rockleigh, NJ 07647 (2013261) Tel: 888.CRESTRON 12.05 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.