Screen Technics MASTERFIT IP Instructions Manual

IP A, A+, B, B+, C, C+ Projection Screen
INSTRUCTIONS - MASTERFIT IP
urchasing a Screen Technics Projection Screen, please ensure that you read
structions fully before installing this product.
Thank you for purchasing a Screen Technics Projection Screen, please
roller for the MasterFit range of projection screens is housed in an insulated
ensure that you read the following instructions fully before installing this
aged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output
product.
plied with a 4 pin WAGO connector with a 4M long 4 core flex allowing
MasterFit IP A, A+, B, B+, C, C+ Projection Screen
bility.
GENERAL INSTRUCTIONS
Thank you for purchasing a Screen Technics Projection Screen, please ensure that you read
the following instructions fully before installing this product.
The motor controller for the MasterFit range of projection screens is housed in an insulated
The motor controller for the MasterFit range of projection screens is housed in an insulated
box and is packaged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output
box and is packaged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output
to motor is supplied with a 4 pin WAGO connector with a 4M long 4 core flex allowing
to motor is supplied with a 4 pin WAGO connector with a 4M long 4 core flex allowing placement flexibility.
placement flexibility.
Close Input
e, dry contact input
A. CONTACT CLOSE INPUT
momentary contact only
1.
Contact Close Input
• No voltage, dry contact input
closed and opened between Up & Common – screen moves to up limit
No voltage, dry contact input
• Requires momentary contact only
closed and opened between Down & Common – screen moves to bottom limit
Requires momentary contact only
• Contact is closed and opened between Up & Common – screen moves to up limit
mand is sent when both Up & Down contact closed together Contact is closed and opened between Up & Common – screen moves to up limit
• Contact is closed and opened between Down & Common – screen moves to bottom limit
Contact is closed and opened between Down & Common – screen moves to bottom limit
• Stop command is sent when both Up & Down contact closed together
Stop command is sent when both Up & Down contact closed together
d Receiver
B. INFRA-RED RECEIVER
with 300mm and 1.2 M lead from motor board to IR receiver 2.
Infra-Red Receiver
Packaged with 300mm and 2 M lead from motor board to IR receiver
with standard 2 channel IR transmitter Packaged with 300mm and 1.2 M lead from motor board to IR receiver
Packaged with standard 2 channel IR transmitter
Packaged with standard 2 channel IR transmitter
erates on group 1 & 2 on infra-red remote
Screen operates on group 1 & 2 on infra-red remote
Screen operates on group 1 & 2 on infra-red remote
D 1 on motor board will flash when IR commands are received
Green LED 1 on motor board will flash when IR commands are received
Green LED 1 on motor board will flash when IR commands are received
A, A+, B, B+, C, C+ Projection Screen
AUSTRALIA
22-24 Suttor Road, Moss Vale NSW 2577
+61 2 4869 2100
C. DC TRIGGER INPUT
• Down command is sent when a DC Voltage above 1.5 Volts @ 1mA minimum is applied to
trigger input
• Up command is sent when a DC Voltage below 1.5 Volts @ 1mA minimum is applied to the
trigger input
• Trigger input is polarity sensitive
• DC voltage must not exceed 15 Volts DC
D. IP INPUT
• DHCP (default setting) or Static IP addressable.
• Access for internal web browser.
• TCP/IP controllable.
INSTALLATION INSTRUCTIONS
STEP 1. Due to the length of the MasterFit boxes, the box will be subject to a slight twist from the
tubular motor, the longer the box the more pronounced it is.
STEP 2. Mounting straps with eyebolts or threaded rod attached at the extremities, should be no
further inboard than 300mm from the end of the box.
STEP 3. To overcome this twist, the ceiling and attachment points are used to stop the twist in
the case.
STEP 4. Due to poor structural integrity of grid type ceilings, you may need to adjust the length
of attachment method (threaded rod or chain with turnbuckles etc.) to minimise box twist.
STEP 5.
Set ceiling installations are generally acceptable, with sufficient structural integrity to
reduce box twist.
NEW ZEALAND
44 Mahana Road, Te Rapa, Hamilton info@screentechnics.com.au
0800 022 821 screentechnics.com.au
1
Continued Over.../
ESTABLISHED IN 1990