Screen Technics ELECTRICINEMA 235 Replacement Instructions

ElectriCinema 235 – Screen surface replacement Instructions
is full up and fully down. This will be needed when resetting the limits later on.
unpacking instruction before starting on the replacement of the screen surface or attempting SCREEN SURFACE REPLACEMENT INSTRUCTIONS - ELECTRICINEMA 235
Please read the unpacking instruction before starting on the replacement of the screen surface or attempting
placement screen from the transport box. Failure to read the unpacking instructions may result
Step 3 – Remove the door stop bracket on the right hand side only using a 4mm Allen key
to remove the replacement screen from the transport box. Failure to read the unpacking instructions may result
e replacement screen surface.
Please read the unpacking instruction before starting on the replacement
in damage to the replacement screen surface.
of the screen surface or attempting to remove the replacement screen
from the transport box. Failure to read the unpacking instructions may
ect the power to the unit.
Step 1 – Disconnect the power to the unit.
result in damage to the replacement screen surface.
oth the doors on ElectriCinema 235, please make a note of the screen surface position when it
Step 2 – Open both the doors on ElectriCinema 235, please make a note of the screen surface position when it
STEP 1. Disconnect the power to the unit.
down. This will be needed when resetting the limits later on.
is full up and fully down. This will be needed when resetting the limits later on.
STEP 2. Open both the doors on ElectriCinema 235, please make a note of the screen surface
the door stop bracket on the right hand side only using a 4mm Allen key
position when it is full up and fully down. This will be needed when resetting the limits later on.
Step 3 – Remove the door stop bracket on the right hand side only using a 4mm Allen key
STEP 3. Remove the door stop bracket on the right hand side only using a 4mm Allen key
Step 4 – Remove rubber block on the right hand side only using a 4mm Allen key
STEP 4. Remove rubber block on the right hand side only
using a 4mm Allen key
e rubber block on the right hand side only using a 4mm Allen key
Step 4 – Remove rubber block on the right hand side only using a 4mm Allen key
Step 5 – Slide out screen surface roller, leaving motor on the left hand side in the place.
Step 5 – Slide out screen surface roller, leaving motor on the left hand side in the place.
Step 6 – Slide the replacement screen surface and tube over the motor, making sure that the tape on the
Step 6 – Slide the replacement screen surface and tube over the motor, making sure that the tape on the
motor drive lines up with the key way in the screen surface tube. (Shown in pictures below)
motor drive lines up with the key way in the screen surface tube. (Shown in pictures below)
Step 6 – Slide the replacement screen surface and tube over the motor, making sure that the tape on the
motor drive lines up with the key way in the screen surface tube. (Shown in pictures below)
Step 6 – Slide the replacement screen surface and tube over the motor, making sure that the tape on the
motor drive lines up with the key way in the screen surface tube. (Shown in pictures below)
AUSTRALIA
22-24 Suttor Road, Moss Vale NSW 2577
+61 2 4869 2100
Step 6 – Slide the replacement screen surface and tube over the motor, makin
STEP 5. Slide out screen surface roller, leaving motor on the left hand side in the place.
motor drive lines up with the key way in the screen surface tube. (Shown in pi
STEP 6. Slide the replacement screen surface and tube over the motor, making sure that the
tape on the motor drive lines up with the key way in the screen surface tube. (Shown in pictures
below)
Step 6 – Slide the replacement screen surface and tube over the motor, makin
motor drive lines up with the key way in the screen surface tube. (Shown in pi
Step 7 – Make sure that the screen surface tube is flush with the flange on t
picture below)
STEP 7. Make sure that the screen surface tube is flush
with the flange on the motor side (as shown in the
picture right)
STEP 8. Replace rubber block using a 4mm Allen Key
STEP 9. Replace door stop using a 4mm Allen Key
Step 8 – Replace rubber block using a 4mm Allen Key
Step 9 – Replace door stop using a 4mm Allen Key
NEW ZEALAND
Step 10 – Once all the bolts have been tightened, reconnect the power to th
44 Mahana Road, Te Rapa, Hamilton info@screentechnics.com.au
controller only.
0800 022 821 screentechnics.com.au
If it is not possible to only connect the one motor controller you will need to b
only operate the screen using the first channel of buttons on the remote con
1
Continued Over.../
ESTABLISHED IN 1990