Download Print this page

Screen Technics ELECTRICINEMA A Instructions

Connect ip projection screen
Hide thumbs Also See for ELECTRICINEMA A:

Advertisement

Quick Links

screen
NEMAPRO Hanging Type Projection Screen
INSTRUCTIONS - ELECTRICINEMA TYPE A, B & C
you for purchasing a Screen Technics Projection Screen, please ensure that you read the following
tions fully before attempting to install this product.
NEMAPRO Hanging Type Projection Screen
Thank you for purchasing a Screen Technics Projection Screen, please
ensure that you read the following instructions fully before attempting to
you for purchasing a Screen Technics Projection Screen, please ensure that you read the following
install this product.
tions fully before attempting to install this product.
l.
Measure the wall where the screen is to be installed and mark with a pencil the desired height to
top of screen case and also the centre of the screen.
WALL MOUNTING INSTRUCTIONS
l.
Measure the wall where the screen is to be installed and mark with a pencil the desired height to
STEP 1.
Measure the wall where the screen is to be installed and mark with a pencil the desired
top of screen case and also the centre of the screen.
height to top of screen case and also the centre of the screen.
2.
Measure the length of screen canister along the top surface and mark the centre of the canister
with a pencil, to assist in lining up the screen when mounting.
STEP 2.
Measure the length of screen canister along the top surface and mark the centre of the
2.
Measure the length of screen canister along the top surface and mark the centre of the canister
canister with a pencil, to assist in lining up the screen when mounting.
with a pencil, to assist in lining up the screen when mounting.
3.
Determine the best positions for the wall brackets, allowing that in Gyprock or in low strength walls
the brackets will be screwed into a timber stud. In more solid walls, such as masonry, position the
brackets approx 150mm in from the canister end. The brackets should be no more than 450mm in
..
,.
-
Connect IP Projection Screen
Wall Mounting Instructions
Wall Mounting Instructions
AUSTRALIA
22-24 Suttor Road, Moss Vale NSW 2577
+61 2 4869 2100
TECHnlCS
STEP 3.
Determine the best positions for the wall brackets, allowing that in Gyprock or in low
strength walls the brackets will be screwed into a timber stud. In more solid walls, such as
masonry, position the brackets approx 150mm in from the canister end. The brackets should
be no more than 450mm in from each end. You must use a minimum of 3 off wood screws per
bracket or 2 off Dyna-bolts, for masonry walls and you must be satisfied that the attachment is
strong enough for the a safe installation.
Brackets supplied as follows, all brackets must be used in installation:
Up to and including 100" = 2 brackets
Over 100" and up to 150" = 3 brackets
150" and up to 200" = 4 brackets
200" = 5 brackets
NB: Top of bracket equals top of screen canister.
STEP 4.
You may need to remove the bottom clip in order to screw brackets to wall, please
ensure to replace them afterwards.
NEW ZEALAND
44 Mahana Road, Te Rapa, Hamilton
info@screentechnics.com.au
0800 022 821
screentechnics.com.au
1
Continued Over.../
ESTABLISHED IN 1990

Advertisement

loading
Need help?

Need help?

Do you have a question about the ELECTRICINEMA A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Screen Technics ELECTRICINEMA A

  • Page 1 INSTRUCTIONS - ELECTRICINEMA TYPE A, B & C Connect IP Projection Screen you for purchasing a Screen Technics Projection Screen, please ensure that you read the following tions fully before attempting to install this product. NEMAPRO Hanging Type Projection Screen Thank you for purchasing a Screen Technics Projection Screen, please STEP 3.
  • Page 2: Ceiling Mount Instructions

    INSTRUCTIONS - ELECTRICINEMA TYPE A, B & C Connect IP Projection Screen CEILING MOUNT INSTRUCTIONS STEP 5. Using two people install the screen by placing the screen canister into the bottom of the bracket clips and pivoting back the canister to slot the top pins into the T channels running along the top of the canister (you may have to remove any tape that is in the way).
  • Page 3 Screen Technics Connect Control Module INSTRUCTIONS - ELECTRICINEMA TYPE A, B & C – Comes standard on all Electricinema Products Connect IP Projection Screen Screen Technics Connect Control Module – Comes standard on all Electricinema Products SCREEN TECHNICS CONNECT CONTROL MODULE •...
  • Page 4 mpleted, plug the screen into a standard power point and turn on. The RJ12 6 Core Straight Through Data cable can link up to 8 Connect controlled devices for multiple switching. mpleted, plug the screen into a standard power point and turn on. The mpleted, plug the screen into a standard power point and turn on.
  • Page 5 er for a beginners guide to basic control functions please download from www.screentechnics.com.au Connect or Mac Connect software and this will assist you in identifying the Connect Module and provide INSTRUCTIONS - ELECTRICINEMA TYPE A, B & C Connect IP Projection Screen ontrol, then guide you by web browser to communicate and program the individual Module.

This manual is also suitable for:

Electricinema bElectricinema c