Viking E-10-IP Product Manual page 5

A. E-10-IP / E-10-IP-EWP / E-30-IP / E-30-IP-EWP
The E-10-IP and E-30-IP are designed to be flush mounted to the included 4" x 4" x 2" deep plastic rough in box or
surface mounted using an optional Viking model VE-5x5. Note: The E-10-IP and E-30-IP will NOT mount to a standard
double gang box. If your application requires a double gang box, see Model E-32-IP. The plastic rough in box (part #
259576) may be purchased separately. Go to www.vikingelectronics.com and click on "Spare Parts".
Dimensions: Overall: 5" x 5" x 2.25" (127mm x 127mm x 57mm), Plastic Rough-In Box: 4" x 4" x 2.12" (102mm x 102mm x 57mm)
E-10-IP Faceplate: 12 gauge aluminum with black textured powder paint
E-30-IP Faceplate: 14 gauge 316 stainless steel with #4 brushed finish
Shipping Weights: E-10-IP: 2 lbs (0.91 kg), E-30-IP: 2.12 lbs (1.0 kg)
Blue LED (E-30-IP/EWP Only): Call connected LED lights steady to help locate the button in low light, flashes during dialing, then
lights steady when answered.
Note: When European CE compliance is required, mount in optional VE-5X5 metal enclosure.
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply a bead of clear silicone caulking around
the top edge / sides of faceplate or VE-5x5.
* Front View of
Plastic Rough-In
Box (included)
** Wire
knock out
(2) Standard
|
flat head dry
wall (sheet
OR
rock) screws
|
(not included)
5.22"
5.14"
2.25"
Front View of Optional
VE-5x5 (not included)
Optional VE-5x5 Surface Mount Box with
black satin powder paint finish, not included
(DOD 424). Optional VE-LIGHT kit can be
used to illuminate the faceplate when used
with a VE-5x5 (DOD 428).
WARNING: Do NOT use a wet location box.
Installation and Specifications
4.0"
Earth Ground the
Green/Yellow
wire using the
provided wire nut
Earth
Ground
(4) T-10 Torx stainless steel,
flat head, security screws
and drive bit (included)
3.25"
(4) 0.38" diameter
(for gooseneck
pedestal mounting)
Condensation
Drain Hole
***(2) 0.74"
diameter
VE-5x5 (not included)
The optional VE-5x5 Surface Mount Box
(above) is designed to be surface mounted
to a single gang box, double gang box or
VE-GNP
right). For more information on the VE-5x5
and VE-GNP, see DOD 424.
2.1"
5.0"
Typical
Push to Call Button
Condensation Drain Hole
Laser Etched Graphics
(2) 0.2 x 0.43 slots for
single gang box
(4) 0.2 x 0.43 slots for
double gang box
3.0" 3.3"
3.0"
Rear View of
Gooseneck Pedestal
5
Peel paper liner and adhere gasket
to back of panel, centering over
mounting holes. Caution: For rough
surfaces (ie: brick, stucco, etc.)
additional caulking may be required.
Model E-30-IP shown
in an optional VE-5x5
Surface Mount Box
mounted to a
VE-GNP Gooseneck
Pedestal
Other pedestal
options available,
see DOD 424
(shown