Viking E-30-PT Product Manual

Viking E-30-PT Product Manual

Speaker phone with push to talk button

Advertisement

Quick Links

Designed, Manufactured and Supported in the USA
VIKING
S E C U R I T Y & C O M M U N I C A T I O N
Provide Reliable and Intelligent
Communication In Noisier Locations
The E-30-PT is designed to provide quick and reliable
communication in noisier areas. The mic sensitivity is set
to a low level until the TALK button is pressed then it is
raised to a normal level. In this way, the E-30-PT assures
that the called party's voice will be broadcast over the
speaker. In applications where the background noise
can be louder than the person calling, a handset type
phone is recommended.
The E-30-PT features non-volatile memory, a built in
dialer, and intelligent call progress detection for automatic
hang-up when the call is completed. The E-30-PT can be
programmed to dial up to 5 different numbers on ring no
answer or busy and can be configured to dial these
numbers until answered.
The E-30-PT-EWP shares all of the features of the
E-30-PT in addition to Enhanced Weather Protection
(EWP) for outdoor installations where the unit is exposed
to precipitation or condensation. EWP products feature
foam rubber gaskets and boots, silicon sealed
Features
• Vandal Resistant Features: 14 gauge louvered 316
stainless steel faceplate with permanent laser etched
graphics, speaker/mic screen, heavy duty metal "Call"
button and T-10 Torx security mounting screws
• Weather Resistant Features: Marine grade 316
stainless steel faceplate, T-screws and push button
switch. Switch internally sealed per IP67. Mylar
speaker. Self-draining mic mount. Faceplate, mic and
speaker gaskets. Weather resistant powder paint on
optional VE-5x5 (DOD 424).
• E-30-PT-EWP is designed to meet IP66 Ingress
Protection Rating (see DOD 859 for more information)
• Push to talk button
• Telephone line powered
2
• Non-volatile E
memory (no batteries required)
• Programmable to dial up to 5 numbers on busy or ring
no answer
• Blue off-hook LED indicator
• Volume adjustments for microphone and speaker
• Advanced call progress detection: disconnects on
busy signal, return to dial tone, CPC, reorder tone,
maximum call time out and programmable silence
time out
• Selectable auto-answer feature for monitoring
• Selectable push button disconnect
• Extended temperature range (-30°F to 150°F)
• Flush mountable using included plastic rough-in box
• Optional VE-5x5 surface mount back box (DOD 424)
PRODUCT MANUAL
S O L U T I O N S
E-30-PT/E-30-PT-EWP
Brushed 316 Stainless steel
shown with optional VE-5x5
connections, gel-filled butt connectors, as well as
urethane or thermal plastic potted circuit boards with
internally sealed, field-adjustable trim pots and DIP
switches for easy on-site programming.
Applications
Non-ADA Hot-Line Phones for:
• Terminals
• Stadiums
• ATM machines
Gate and Door Entry Phones for:
• Business lobbies
• Vehicular and Pedestrian gates
CAUTION - When installing on an analog extension of a phone
system: Some phone systems do not conform to analog telecom
standards and might not be compatible with the E-30-PT speaker
phones. For a detailed description of the telephone line
specifications required for any of the E-30-PT phones, see DOD#
869.
Specifications
Power: Telephone line powered. Minimum 24V DC talk
battery voltage, with a minimum loop current of 20mA
loop. Loop current may be boosted on low current lines
with a Viking Model TBB-1B talk battery booster (see
DOD 632).
Minimum Ring Voltage: 90VAC RMS
Dimensions: Overall-5" x 5" x 2.25" (127mm x 127mm x
57mm), Plastic Electrical Box-4" x 4" x 2.12" (102mm x
102mm x 54mm )
Shipping Weight: 2.2 lbs (1 Kg)
Operating Temperature: -30°F to 150°F (-34°C to 65° C)
Humidity - E-30-PT: 5% to 95% non-condensing
Humidity - E-30-PT-EWP: Up to 100% condensing
Connections - E-30-PT: RJ11 jack
Connections - E-30-PT-EWP: Gel-filled butt connectors
E-30-PT/EWP
Speaker Phone with
Push to Talk Button
February 5, 2018
• Parking lots/ramps
• Convention centers
• Residences

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E-30-PT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Viking E-30-PT

  • Page 1 The mic sensitivity is set to a low level until the TALK button is pressed then it is raised to a normal level. In this way, the E-30-PT assures that the called party’s voice will be broadcast over the speaker.
  • Page 2: Features Overview

    Caution: When warm air comes in contact with cold surfaces, such as outside walls, it causes condensation. To help prevent condensation from accumulating inside the E-30-PT, bring conduit into the bottom of the unit. If this is not possible, drill a 1/4” diameter hole in the bottom of the plastic rough-in box.
  • Page 3 (included) from the mounting screw to Earth Ground (grounding rod, water pipe, etc.) Programming The E-30-PT phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a DLE-200B Line Simulator. For more information on the DLE-200B, see DOD 605.
  • Page 4 C. Security Code (memory location #19) The security code allows the user/installer to program the E-30-PT phone while DIP switch 3 is in the ON (normal) position. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code be changed.
  • Page 5: Touch Tone

    Tones 1 - 9). Program 0 in this location to disable the call length time out. With 1 min the call length disabled, the E-30-PT phone must rely on CPC, busy, silence or 2 min return dialtone to hang-up. Use chart at the right. *Note: The factory default is 3 minutes.
  • Page 6 CO line, or behind a "dial 9" PBX. The E-30-PT phone will first dial 9, and then listen for second dial tone; if detected it will continue to dial Viking’s assisted programming phone number. If a second dial tone is not detected, it then knows is not behind a PBX, so it will momentarily hang up and then directly dial Viking’s assisted programming phone number.
  • Page 7 Learn mode - Any incoming calls are automatically entered into the programming mode (no security code required). Use this option if you have forgotten your security code. Any outbound call will dial Viking Technical Support (see section I). Warning: When finished programming, set this switch back to the ON position, otherwise the 1600A Series phone will only call Viking Technical Support instead of your pro- grammed emergency number.
  • Page 8: Operation

    TWO YEAR LIMITED WARRANTY Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of two years from the date of purchase from any authorized Viking distributor. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016.

This manual is also suitable for:

E-30-pt-ewp

Table of Contents