36
REMPLACEMENT COURROIE
DE COMMANDE BALAI
LATERAL DROIT
Pour remplacer cette courroie, procéder
comme suit:
•
Démonter le panneau latéral droit 1.
•
Desserrer le tendeur 2 de la courroie de
renvoi 3.
•
Retirer la courroie de renvoi 3 de la
poulie 4.
•
Desserrer le tendeur 5 de la courroie de
commande du balai central.
•
Retirer la courroie 6 de la poulie 4.
•
Remplacer la courroie 7 du balai latéral.
•
Remonter la courroie 6 sur la poulie 4.
•
Tendre la courroie 6 à l'aide du tendeur
5.
•
Remonter la courroie 3 sur la poulie 4.
•
Tendre la courroie 3 à l'aide du tendeur
2.
•
Remonter le panneau latéral 1.
Lors du remplacement de la courroie, il est
conseillé de vérifier également les courroies de
commande balais 3 et 6 (fig. 11).
En cas d'usure des courroies, les remplacer
immédiatement pour éviter toute perte de
temps due au démontage de pièces.
Atom H
FITTING THE RH SIDE BRUSH
SECONDARY DRIVE BELT
Proceed as follows to fit a new RH side brush
secondary drive belt:
•
Remove the right-hand side cover 1.
•
Back off the belt stretcher 2 of the
transmission belt 3.
•
Remove the transmission belt 3 from the
pulley 4.
•
Back off the belt stretcher 5 of the main
brush drive belt.
•
Remove the belt 6 from the pulley 4.
•
Replace the belt 7 of the side brush.
•
Replace the belt 6 on the pulley 4.
•
Tension the belt 6 using the belt stretcher
5.
•
Replace the belt 3 on the pulley 4.
•
Tension the belt 3 using the belt stretcher
2.
•
Replace the side cover 1.
Take the opportunity to check the condition of
the primary drive belts 3 and 6, fig. 11 and
replace if worn.
If belts show signs of wear, replace them to
avoid further down-times for more dismantling
of parts.
SUSTITUCIÓN DE LA CORREA
DE ACCIONAMIENTO DEL
CEPILLO LATERAL DER.
Para
sustituir
esta
correa
siguientes operaciones:
•
Desmontar el cárter lateral derecho 1.
•
Aflojar el tensor 2 de la correa de
transmisión 3.
•
Quitar la correa de transmisión 3 de la
polia 4.
•
Aflojar el tensor 5 de la correa de
accionamiento del cepillo central.
•
Quitar la correa 6 de la polea 4.
•
Quitar la correa 7 del cepillo lateral.
•
Volver a montar la correa 6 en la polea 4.
•
Tensar la correa 6 con el tensor 5.
•
Volver a montar la correa 3 en la polea 4.
•
Tensar la correa 3 con el tensor 2.
•
Volver a montar el cárter lateral 1.
Se recomienda que al sustituir la correa
también se comprueben las correas de
accionamiento de los cepillos 3 y 6 (Fig. 11).
Si se observa que las correas están en mal
estado, cambiarlas para evitar pérdidas de
tiempo con otros desmontajes de piezas.
efectuar
las