Table of Contents
Advertisement
B
Y
EFORE
OU
What is included
ART-150W – Spectrum™ 150W or
ART-252W – Spectrum™ 252W & foot brackets
Power cord attached with bare ends
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all
parts are present, and have been received in good condition. Notify the shipper immediately and retain
packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs
of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to
the factory, it is important that the fixture be returned in the original factory box and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of the
fixture or refer to the fixture's specifications chart. A fixture's listed current rating is its average current draw
under normal conditions. All fixtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%
to 100% switch. Before applying power to a fixture, check that the source voltage matches the fixture's
requirement. Check the fixture or device carefully to make sure that if a voltage selection switch exists that
it is set to the correct line voltage you will use.
Warning!
Verify that the power select switch on your unit matches the line voltage applied. All
fixtures must be connected to circuits with a suitable Earth Ground.
Safety Instructions
•
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
•
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
•
To prevent risk of fire or shock make sure there are no
flammable materials close to the unit while operating.
•
The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
•
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
•
Maximum ambient temperature is Ta: 50°. Do not operate
fixture at temperatures higher than this.
•
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
Caution!
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
CHAUVET.
ART-150W & ART-252W User Manual
B
EGIN
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?
MSD-250 or
CDM-150 Discharge lamp
Warranty Card & Manual
authorized technical assistance center. Always use the
same type spare parts.
•
Don't connect the device to a dimmer pack.
•
Make sure power cord is never crimped or damaged.
•
Never disconnect power cord by pulling or tugging on the
cord.
•
Avoid direct eye exposure to lamp while it is on.
•
Check your power cables carefully to ensure that
there are no cuts or breach of integrity of the outer
shell at any point. Moisture could be drawn up inside
the cable due to a vacuum generated by heat inside
the fixture.
•
Protect connectors for both power and data lines in a
weatherproof housing or a weatherproof junction
box.
•
If you don't hard wire the fixture to a weatherproof
junction box, make sure to use an IP55 or better rated
connector for both plugs and connectors.
•
Do not connect to a dimmer system.
•
For your protection, the fixture must be grounded and
the AC mains supply must be outfitted with a circuit
breaker and ground-fault protection.
3
2005-01-31/12:52
Advertisement
Table of Contents
