Chauvet LED Techno Strobe User Manual
3-channel dmx-512 led white strobe light
Hide thumbs
Also See for LED Techno Strobe:
- Pocket manual (2 pages) ,
- User manual (2 pages) ,
- Brochure & specs (24 pages)
Related Manuals for Chauvet LED Techno Strobe
Summary of Contents for Chauvet LED Techno Strobe
-
Page 1: User Manual
LED Techno Strobe™ ST-3000LED USER MANUAL CHAUVET, 5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A (800) 762-1084 – (954) 577-4455 FAX (954) 929-5560 www.chauvetlighting.com... -
Page 2: Table Of Contents
©CHAUVET, 2013, All Rights Reserved Information and specifications in this User Manual are subject to change without notice. CHAUVET assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. LED Techno Strobe™ User Manual... -
Page 3: Before You Begin
Before You Begin 1. Before You Begin What is Included · · 1 x LED Techno Strobe™ ST-3000LED Warranty Card · · 1 x Power cable User Manual · 2 x Flush Mount Brackets with screws Unpacking Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. -
Page 4: Introduction
· Adjustable flash rate, dimmer and static via stand-alone · Automatic built-in programs with sound activation · Linkable with LED Techno Strobe™ & LED Shadow™ in stand-alone · Low power consumption · Additional power output for daisy chaining units together... -
Page 5: Product Overview
Rotary knob DIP-switches DMX Input Power Link Out DMX Addressing DMX Output Red LED: Power Indicator Blue LED: Signal Indicator IEC Plug for AC Input & Fuse Compartment Flush Mounting Bracket LED Front Panel LED Techno Strobe™ User Manual Rev. 5... -
Page 6: Setup
You must supply your own clamp and make sure the clamp is capable of supporting the weight of this fixture. You can order C-clamps from any CHAUVET dealer or distributor. Block access below the work area and use suitable and stable platform when installing or servicing fixture. -
Page 7: Fixture Linking
(male) 3-pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. LED Techno Strobe™ User Manual Rev. 5... -
Page 8: Operating Instructions
3000LED fixtures in what is called a “Master/Slave” configuration. Single-Fixture Mode The ST-3000 LED Techno Strobe can be set to operate independently of other fixtures or a DMX controller in either a sound-active or automatic mode. A serial data-link is not necessary for this mode of operation and it is recommended that no connection to other fixtures be made at all. -
Page 9: Appendix
Products returned without an RMA # will be refused. Call CHAUVET and request an RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. -
Page 10: Binary Addressing Quick Reference Chart
Appendix Binary Addressing Quick Reference Chart DMX & Binary Address Quick Reference Chart DIP-switch Position DMX DIP-SWITCH SET #9 0=OFF 1=ON X=OFF or ON DIP-switch Position DMX Address LED Techno Strobe™ User Manual Rev. 5... -
Page 11: Dmx Channel Values
120 ó 149 Program 4 150 ó 179 Program 5 180 ó 209 Program 6 210 ó 255 Sound No Function Photometric 20° Beam Angle Foot Candles 1800 Distance (feet) 0.304 0.914 1.828 Distance (meters) LED Techno Strobe™ User Manual Rev. 5... -
Page 12: Technical Specifications
Data output ........................locking 3-pin XLR female socket Data pin configuration ....................... pin 1 shield, pin 2 (-), pin 3 (+) Protocols ..............................DMX-512 USITT DMX Channels.................................. 3 ORDERING INFORMATION LED Techno Strobe™ ........................... ST-3000LED Contact Us Wor l d Wi de General Information CHAUVET® Lighting...