Filtered boiling, chilled and chilled sparkling drinking water with unfiltered mixed hot and cold water for residential kitchens celsius residential series (29 pages)
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Refrigerant The Zip HydroChill Command Centre contains R134a refrigerant under pressure. Maintenance of the refrigeration unit must be carried out by an accredited service provider or qualified refrigeration technician.
The HydroChill must be sanitised during the commission process, please contact the Zip Water team on 0345 6 005 005 to book your commissioning service. For water taste and quality reasons any non-use of more than 48 hours, Zip recommend a system flush be performed.
Vent kit,4 parts Installation instructions T25 torx double ended key Door buffer self adhesive Branch stem tee 3 x 1/4” Accessories To order spare parts and accessories Call Zip on 0345 6 005 005. Accessories Item Part No. Description Optional HE45004 Water block (water shut down system) Pressure reducing valve (3.5 bar)
See Technical specification, page 4 for dimensions. • For Zip HydroChill HC45 models, 1 x 220-240V AC 13A socket will be required. • The Command Centre must be installed in accordance with IEE regulations, See Technical specification, page 4 for power ratings.
Section 1 Water block (optional) Description • The Water Block is designed to be installed upstream of any Zip product and associated pipe- work to minimise the potential for water leakage in the event of a system malfunction. • The Water Block is ideal for limiting potential leakage and resulting water damage from water heaters, water chillers etc.
Page 8
The reset device (see Fig.2) may be fitted to avoid disconnection. This allows the Water Block to be reset by operating the lever in the direction shown in Fig.2. • In the event of persistent tripping contact Zip for advice on 0345 6 005 005. 1.3 Maintenance •...
Installation - Section 2 Ventilation 2.1 Generic requirements Important Read this section in conjunction with section 4 Command Centre installation, page 13. When installing air flow vents, the following tools will be required • Jigsaw and drill or equivalent equipment. •...
Page 10
Installation - Section 2 Ventilation 2.2 Ventilation for all models • The clearance envelope dimensions stated in the specification sheets and installation instructions must be observed. • Adequate ventilation must be provided to ensure that the cupboard space temperature does not exceed 35 2.3 Preferred ventilation arrangements for commercial models •...
Page 11
Installation - Section 2 Ventilation 2.4 Alternative arrangement (Vent tray) In situations where cupboard width is 1000mm or greater, without central pillar and where vent grilles cannot be fitted in the kick board (e.g. hospitals) use a Vent tray kit (SP93541). A vent grille, supplied should be used as an inlet vent and fitted to the cabinet side (adjacent to the Command Centre air inlet) as shown below.
Installation - Section 3 Tap installation 3.1 Configure the twin lever tap 3.3 Configure the heavy duty tap Twin lever Heavy duty Upper rubber washer Worktop Worktop Washer Lower rubber washer Lower rubber washer Red, white and blue pipes Red, white and blue pipes 3.2 Cut the hole &...
Installation - Section 4 Command Centre installation 4.1 Generic Command Centre installation instructions Read these instructions before commencing Command Centre installation, they apply to all installation arrangements. • Install the mains water braided hoses to the Command Centre before locating in place. •...
Installation - Section 5 Command Centre installation, Chilled only installation 5.1 HydroChill chilled only model HC45T128 Heavy duty 5.2 Manifold connections CHILLED MAINS WATER IN Connect to Connect to Mains (Cat 1) Cold water White 1/4” pipe from tap supply Connect to 1/4”...
Installation - Section 6 Command Centre installation, Chilled ambient installation 6.1 HydroChill chilled ambient model HC45T1228 Twin lever Connect to 6.2 Manifold connections White 1/4” pipe from tap CHILLED MAINS WATER IN Connect to Mains (Cat 1) Cold water Connect to supply Blue 1/4”...
If your HydroChill is left idle before use for water taste and quality reasons any non-use of more than 48 hours, Zip recommend a system flush be performed. On first use after a period of non-use, run the chilled / ambient water functions for 60 seconds to flush the filter and system.
Not changing the filters when required may cause the water to become biologically unsafe. Pull Use only a Zip filter to match the one used in your system product (see Spare parts page 5). The filter cartridge can be obtained through plumbing suppliers or direct from Zip. The installation Rotate date should be written on the filter cartridge.
• The Zip filter should be replaced at least every 12 months, at the rated capacity or sooner if you notice a persistent reduction in water flow from the tap or an unpleasant taste or odour in the water. As stated on the filter cartridge.
Service Work Ad hoc repairs by Zip or its approved service providers are covered under Warranty for 30 days in relation to the original fault only. If you are a HydroCare Service Plan subscriber please refer to the HydroCare terms and conditions for information on applicable warranties and warranty periods for HydroCare services.