Advertisement
Quick Links
Operation Manual
2 in 1 Brush Cutter
61495, 61496
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61495
Summary of Contents for WilTec 61495
- Page 1 Operation Manual 2 in 1 Brush Cutter 61495, 61496 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Never remodel your brush cutter. We shall not warrant the machine, if you use a re - modelled brush cutter or you do not observe the proper usage described in the manual. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 3 http://www.WilTec.de...
- Page 4 10 Throttle lever Air cleaner 11 Throttle cable Stand 12 Outer pipe Engine switch button 13 Safety guard Housing 14 Gear case Hanger 15 Blade Handle © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 4 http://www.WilTec.de http://www.aoyue.eu 02 2021-2 http://www.teichtip.de...
- Page 5 • whenever any questions arise. Never allow children or anyone unable to fully understand the directions • given in this manual to use this brush cutter. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 5 http://www.WilTec.de http://www.aoyue.eu 02 2021-2...
- Page 6 After refuelling, screw the fuel cap back tightly onto the fuel tank and then carry the product to • a spot 3 m or more away from where it was refuelled before turning on the engine. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 6 http://www.WilTec.de...
- Page 7 3. When using your brush cutter never take your eyes off, if you need to place the throttle into the idling position. 4. When using your brush cutter do not let the unit get close to your feet nor raise the unit above your waist. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 When replacing blade or any other parts or when replacing the oil or any lubricants always be • sure to use only products which have been certified by for use with the brush cutter. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 8 http://www.WilTec.de...
- Page 9 And set the cable in the lever as shown in the picture. b) Wrap the band so as the throttle wire is fixed with the handle. № Name № Name Hole Throttle wire © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 9 http://www.WilTec.de http://www.aoyue.eu 02 2021-2 http://www.teichtip.de...
- Page 10 L-shaped bar and tighten it manually. d) Keep bolts and washers to install the blade carefully. № Name № Name Gear case Nylon cutter Bolt Nylon cord © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 10 http://www.WilTec.de http://www.aoyue.eu 02 2021-2 http://www.teichtip.de...
- Page 11 Mix a regular grade gasoline (leaded or unleaded) and a quality- proven motor oil for air-cooled 2 cycle engines. RECOMMENDED MIXING RATIO GASOLINE:OIL = 25:1 © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 11 http://www.WilTec.de http://www.aoyue.eu 02 2021-2 http://www.teichtip.de...
- Page 12 When restarting immediately after stopping the engine move the throttle lever to the idling position. № Name № Name Idling Full throttle Starting ( – open) © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 12 http://www.WilTec.de http://www.aoyue.eu 02 2021-2 http://www.teichtip.de...
- Page 13 In order to prevent stack during operation turn up the ex- tra part of the band from the buckle. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 13 http://www.WilTec.de...
- Page 14 If you try to cut grass by swinging the brush cutter in the reverse way (from left to right) scraps • fly in the direction away from the body, so you can avoid getting your clothes dirty. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 14 http://www.WilTec.de...
- Page 15 Take the filter out of the fuelling port using a small wire hook. Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it. Clean the components with gasoline. A clogged fuel fitter may cause poor acceleration of the engine. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 15 http://www.WilTec.de...
- Page 16 A wrong adjustment may cause damage to your unit. If the engine does not run well after adjusting the carburettor, please contact the shop where you purchased the product. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 16 http://www.WilTec.de...
- Page 17 Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions manual require the written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 61495, 61496 Page 17 http://www.WilTec.de...