VAT 264 Series Installation, Operating, & Maintenance Instructions
Hv-angle valve, hv-inline valve, dn 10 - 16 (i.d. 3/8-5/8")
Hide thumbs
Also See for 264 Series:
Table of Contents
Advertisement
HV-Angle Valve
HV-Inline Valve
with electromagnetic actuator
single acting with closing spring (NC)
This manual is valid for the valve ordering number(s):
26...
26
4
24
-K 61
A
A ..
K ..
20.. DN 10
4 ..
The fabrication number is indicated on each product as per the label
below (or similar):
ma de in S wit zerlan d
Fab rica tion No .:
pa te nte d
2 6 . . . – . . . . – . . . . / . . . .
A – . . . . . .
Explanation of symbols:
Read declaration carefully before you start any other
action!
Attention!
Product is in conformity with EC guidelines,
if applicable!
Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!
Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com
Installation, Operating & Maintenance Instructions
Series 264, DN 10 - 16 (I.D. 3/8 - 5/8")
(Series 264)
(Series 265)
Aluminum
E .. Stainless Steel
ISO-KF
G .. CF-R
24 .. DN 16
Angle Valve
5 .. Inline Valve
. .
Fabrication number
Keep body parts and objects away from the valve
opening!
Hot surfaces; do not touch!
Loaded springs and/or air cushions are potential
hazards!
Wear gloves!
279114EC
2010-10-06
1/10
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VAT 264 Series
Summary of Contents for VAT 264 Series
- Page 1 Do not touch parts under voltage! Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General Safety Instructions» carefully before you start any other action! VAT Vakuumventile AG, CH-9469 Haag, Switzerland 279114EC 1/10 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
- Page 2 VAT products. The VAT firmware contains a limited, time unlimited user license. The VAT firmware may not be used for purposes other than those intended nor is it permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to other people.
-
Page 3: Table Of Contents
5.1 Replacement of Seals ............................8 6 Drawing..................................9 7 Spare parts ................................9 8 Warranty ................................. 10 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 279114EC 3/10 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 4: Use Of Product
Series 264, DN 10 - 16 (I.D. 3/8 - 5/8") Use of product Use product for clean and dry indoor vacuum applications under the conditions indicated in chapter «Technical data» only! Other applications are only allowed with the written permission of VAT. Technical data Leak rate <... -
Page 5: Installation
«F » lbf . ft inch A combination of both forces «F » and «M» is prohibited. Please contact VAT. Connections Do not touch parts under voltage! Connect electrical power only when - valve is installed into the system - moving parts cannot be touched... -
Page 6: Safety Low Voltage Control (20
The green LED will indicate the open valve position. After switching off the power, the orange LED might indicate the closed valve position, but the light will fade out shortly afterwards. Note: This connection diagram can be used to replace valves in case no L’ signal is available. VAT Vakuumventile AG, CH-9469 Haag, Switzerland 279114EC 6/10 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 7: Line Voltage Control (100
If you need any further information, please contact one of our service centers. You can find the addresses on our website: http://www.vat.ch VAT Vakuumventile AG, CH-9469 Haag, Switzerland 279114EC 7/10 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 8: Maintenance & Repairs
Contamination from the process may influence the function and requires more frequent maintenance. Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the valve made in Switzerland Fabrication No.:... -
Page 9: Drawing
Extras Item Description 61, 62, 63 Seal Kit Coil with Electronics VAT Vakuumventile AG, CH-9469 Haag, Switzerland 279114EC 9/10 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2010-10-06... -
Page 10: Warranty
(including any delay in or failure to deliver), packaging, storage or use of any product sold or delivered by VAT shall fail to conform to the...
Need help?
Do you have a question about the 264 Series and is the answer not in the manual?
Questions and answers